When installing the name plates, heat the vehicle body, back door outside garnish and name plates using a heat light.
| Item | Temperature |
|---|---|
| Vehicle Body | 40 to 60°C (104 to 140°F) |
·
Back Door Outside Garnish ·
Name Plates |
20 to 30°C (68 to 86°F) |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts, touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the vehicle body, back door outside garnish or name plates excessively.
75361A
1.INSTALL NO. 1 FRONT FENDER NAME PLATE
Clean the vehicle body surface.
Using a heat light, heat the vehicle body surface.
Remove any remaining double-sided tape from the vehicle body.
Wipe off any tape adhesive residue with cleaner.
Using a heat light, heat the vehicle body and a new No. 1 front fender name plate.
Remove the release paper from the No. 1 front fender name plate.
After removing the release paper, keep the exposed adhesive free from foreign matter.
for LH Side:
Install the No. 1 front fender name plate as shown in the illustration.
| *a | Reference Values | *b | End of R |
| Area | Measurement | Area | Measurement |
|---|---|---|---|
| A | 239.9 mm (9.44 in.) | B | 201.2 mm (7.92 in.) |
| C | 49.4 mm (1.94 in.) | D | 102.5 mm (4.04 in.) |
for RH Side:
Install the No. 1 front fender name plate as shown in the illustration.
| *a | Reference Values | *b | End of R |
| Area | Measurement | Area | Measurement |
|---|---|---|---|
| A | 232.4 mm (9.15 in.) | B | 211.3 mm (8.32 in.) |
| C | 105.4 mm (4.15 in.) | D | 49 mm (1.93 in.) |
75441E
2.INSTALL NO. 1 BACK DOOR NAME PLATE
Clean the back door outside garnish surface.
Using a heat light, heat the back door outside garnish surface.
Remove any remaining double-sided tape from the back door outside garnish.
Wipe off any tape adhesive residue with cleaner.
Using a heat light, heat the back door outside garnish and a new No. 1 back door name plate.
Remove the release paper from the No. 1 back door name plate.
After removing the release paper, keep the exposed adhesive free from foreign matter.
| *a | location pin |
Engage the location pins and install the No. 1 back door name plate as shown in the illustration.
75442A
3.INSTALL NO. 2 BACK DOOR NAME PLATE
Clean the back door outside garnish surface.
Using a heat light, heat the back door outside garnish surface.
Remove any remaining double-sided tape from the back door outside garnish.
Wipe off any tape adhesive residue with cleaner.
Using a heat light, heat the vehicle body and a new No. 2 back door name plate.
Remove the release paper from the No. 2 back door name plate.
After removing the release paper, keep the exposed adhesive free from foreign matter.
| *a | location pin |
Engage the location pins and install the No. 2 back door name plate as shown in the illustration.
75444A
4.INSTALL NO. 4 BACK DOOR NAME PLATE
Clean the vehicle body surface.
Using a heat light, heat the vehicle body surface.
Remove any remaining double-sided tape from the vehicle body.
Wipe off any tape adhesive residue with cleaner.
Using a heat light, heat the vehicle body and a new No. 4 back door name plate.
Remove the release paper from the No. 4 back door name plate.
After removing the release paper, keep the exposed adhesive free from foreign matter.
Install the No. 4 back door name plate as shown in the illustration.
| *a | Reference Values | *b | End of R |
| Area | Measurement | Area | Measurement |
|---|---|---|---|
| A | 97 mm (3.82 in.) | B | 225.6 mm (8.88 in.) |
| C | 89 mm (3.50 in.) | D | 110 mm (4.33 in.) |
75741E
5.INSTALL SYMBOL EMBLEM
Clean the back door outside garnish surface.
Using a heat light, heat the back door outside garnish surface.
Remove any remaining double-sided tape from the back door outside garnish.
Wipe off any tape adhesive residue with cleaner.
Using a heat light, heat the vehicle body and a new symbol emblem.
Remove the release paper from the symbol emblem.
After removing the release paper, keep the exposed adhesive free from foreign matter.
| *a | location pin |
Engage the location pins and install the symbol emblem as shown in the illustration.