Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › ROOF DRIP SIDE FINISH MOULDING › from 2020.09
RM36W0E _59 Vehicle Exterior _088302 EXTERIOR PANELS / TRIM _0421046 ROOF DRIP SIDE FINISH MOULDING A

EXTERIOR PANELS / TRIM  ROOF DRIP SIDE FINISH MOULDING  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 75561 1.INSTALL NO. 1 ROOF DRIP SIDE FINISH MOULDING CLIP (for 5 Door)

NOTICE:

When installing new No. 1 roof drip side finish moulding clips, remove any adhesive remaining where the No. 1 roof drip side finish moulding clips will be installed on the vehicle body and clean the vehicle body with a non-residue solvent.


a.

w/o Glass Roof:

i.
B591413C01
2.167,0.396 2.479,0.396 false 0.75,0.583 1.594,1.021 true 1.969,0.313 2.281,0.469 0.313,0.156 10 false *a 0.563,0.469 0.875,0.625 0.313,0.156 10 false *b
*a Adhesive
*b 2 to 3 mm Bead of Adhesive


Apply a 2 to 3 mm (0.0787 to 0.118 in.) bead of adhesive (3M DP-105 or equivalent) to each new No. 1 roof drip side finish moulding clip.

HINT:

Adhesive strength (tensile strength): 13.7 MPa (140.0 kgf/cm2, 1987 psi) or more (when the temperature is 23°C (73°F).)



ii.

Install the No. 1 roof drip side finish moulding clips to the positions on the roof panel shown in the illustration. Determine the locations and firmly press and install the No. 1 roof drip side finish moulding clips.

B577643C01
0.281,0.156 0.594,0.354 0.313,0.198 10 false *a 1.125,0.229 1.438,0.427 0.313,0.198 10 false A 2.344,0.323 2.656,0.521 0.313,0.198 10 false B 1.927,0.167 2.24,0.365 0.313,0.198 10 false *b 1.229,2.167 1.427,2.406 0.198,0.24 10 true *a 1.958,2.281 2.156,2.49 0.198,0.208 10 true *b 4.146,1.646 4.458,1.844 0.313,0.198 10 false *a 5.094,1.708 5.406,1.906 0.313,0.198 10 false C 5.875,1.656 6.188,1.854 0.313,0.198 10 false *b 6.26,1.76 6.573,1.958 0.313,0.198 10 false D 5.844,0.729 6.042,0.969 0.198,0.24 10 true *a 5.396,1.281 5.594,1.49 0.198,0.208 10 true *b
*a View A *b View B


Standard Measurement:
Area Measurement Area Measurement
A 1.5 to 2.5 mm (0.0591 to 0.0984 in.) B 4.0 mm (0.157 in.)
C 1.9 to 2.9 mm (0.0748 to 0.114 in.) D 4.0 mm (0.157 in.)



iii.

Install the roof drip side finish moulding when 40 minutes or more have elapsed since the No. 1 roof drip side finish moulding clips were installed.

HINT:
·

Initial hardening time: 40 minutes

·

Complete hardening time: 24 hours





Hide 75561 2.INSTALL NO. 1 ROOF DRIP SIDE FINISH MOULDING CLIP (for 5 Door)

NOTICE:

When installing new No. 1 roof drip side finish moulding clips, remove any adhesive remaining where the No. 1 roof drip side finish moulding clips will be installed on the vehicle body and clean the vehicle body with a non-residue solvent.


a.

w/ Glass Roof:

i.
B591413C01
2.167,0.396 2.479,0.396 false 0.75,0.583 1.594,1.021 true 1.969,0.313 2.281,0.469 0.313,0.156 10 false *a 0.563,0.469 0.875,0.625 0.313,0.156 10 false *b
*a Adhesive
*b 2 to 3 mm Bead of Adhesive


Apply a 2 to 3 mm (0.0787 to 0.118 in.) bead of adhesive (3M DP-105 or equivalent) to each new No. 1 roof drip side finish moulding clip.

HINT:

Adhesive strength (tensile strength): 13.7 MPa (140.0 kgf/cm2, 1987 psi) or more (when the temperature is 23°C (73°F).)



ii.

Install the No. 1 roof drip side finish moulding clips to the positions on the roof panel shown in the illustration. Determine the locations and firmly press and install the No. 1 roof drip side finish moulding clips.

B567997C01
0.313,0.198 0.625,0.354 0.313,0.156 10 false *a 1.635,0.198 1.948,0.354 0.313,0.156 10 false *b 0.885,0.24 1.198,0.396 0.313,0.156 10 false A 2.375,0.458 2.688,0.615 0.313,0.156 10 false B 4.406,0.208 4.719,0.365 0.313,0.156 10 false *a 5.979,0.219 6.292,0.375 0.313,0.156 10 false *b 5.177,0.26 5.49,0.417 0.313,0.156 10 false C 6.333,0.271 6.646,0.427 0.313,0.156 10 false D 2.979,1.917 3.167,2.083 0.188,0.167 10 true *b 3.917,1.854 4.104,2.021 0.188,0.167 10 true *b 2.417,1.51 2.625,1.688 0.208,0.177 10 true *a 4.417,1.396 4.625,1.573 0.208,0.177 10 true *a
*a View A *b View B


Standard Measurement:
Area Measurement Area Measurement
A 1.9 to 2.9 mm (0.0748 to 0.114 in.) B 37.8 mm (1.488 in.)
C 1.9 to 2.9 mm (0.0748 to 0.114 in.) D 4.0 mm (0.157 in.)



iii.

Install the roof drip side finish moulding when 40 minutes or more have elapsed since the No. 1 roof drip side finish moulding clips were installed.

HINT:
·

Initial hardening time: 40 minutes

·

Complete hardening time: 24 hours





Hide 75561 3.INSTALL NO. 1 ROOF DRIP SIDE FINISH MOULDING CLIP (for 3 Door)

NOTICE:

When installing new No. 1 roof drip side finish moulding clips, remove any double-sided tape and adhesive remaining where the No. 1 roof drip side finish moulding clips will be installed on the vehicle body and clean the vehicle body with a non-residue solvent.


a.
B591413C01
2.167,0.396 2.479,0.396 false 0.75,0.583 1.594,1.021 true 1.969,0.313 2.281,0.469 0.313,0.156 10 false *a 0.563,0.469 0.875,0.625 0.313,0.156 10 false *b
*a Adhesive
*b 2 to 3 mm Bead of Adhesive


Apply a 2 to 3 mm (0.0787 to 0.118 in.) bead of adhesive (3M DP-105 or equivalent) to each new No. 1 roof drip side finish moulding clip.

HINT:

Adhesive strength (tensile strength): 13.7 MPa (140.0 kgf/cm2, 1987 psi) or more (when the temperature is 23°C (73°F).)



b.

Install the No. 1 roof drip side finish moulding clips to the positions on the roof panel shown in the illustration. Determine the locations and firmly press and install the No. 1 roof drip side finish moulding clips.

B612671C01
1.802,0.156 2.115,0.354 0.313,0.198 10 false *b 0.344,0.156 0.656,0.354 0.313,0.198 10 false *a 1.083,0.167 1.396,0.365 0.313,0.198 10 false A 1.781,0.521 2.094,0.719 0.313,0.198 10 false B 2.292,1.031 2.604,1.229 0.313,0.198 10 false C 4.115,1.635 4.427,1.833 0.313,0.198 10 false *c 5.333,1.646 5.646,1.844 0.313,0.198 10 false *b 4.896,1.719 5.208,1.917 0.313,0.198 10 false D 5.375,1.979 5.688,2.177 0.313,0.198 10 false E 6.729,1.958 7.042,2.156 0.313,0.198 10 false F 1.573,1.26 1.76,1.438 0.188,0.177 10 true *b 1.49,2.156 1.677,2.333 0.188,0.177 10 true *a 5.115,0.354 5.302,0.531 0.188,0.177 10 true *b 5.802,0.76 5.99,0.938 0.188,0.177 10 true *c 6.198,2.49 6.51,2.688 0.313,0.198 10 false G
*a View A *b View B
*c View C - -


Standard Measurement:
Area Measurement Area Measurement
A 1.6 to 2.6 mm (0.063 to 0.102 in.) B 1.0 mm (0.0394 in.)
C 5.1 mm (0.201 in.) D 2.9 mm (0.114 in.)
E 1.2 mm (0.0472 in.) F 4.6 mm (0.181 in.)
G 5.9 mm (0.232 in.) - -



c.

Install the roof drip side finish moulding when 40 minutes or more have elapsed since the No. 1 roof drip side finish moulding clips were installed.

HINT:
·

Initial hardening time: 40 minutes

·

Complete hardening time: 24 hours




Hide 75552 4.INSTALL ROOF DRIP SIDE FINISH MOULDING (for 5 Door)

a.

w/o Glass Roof:

i.
B567993

Engage the clips to install the roof drip side moulding.


ii.

Remove the protective tape.



Hide 75552 5.INSTALL ROOF DRIP SIDE FINISH MOULDING (for 5 Door)

a.

w/ Glass Roof:

i.
B567995

Engage the clips to install the roof drip side moulding.


ii.

Remove the protective tape.



Hide 75552H 6.INSTALL ROOF DRIP SIDE MOULDING (for 3 Door)

a.

Clean the vehicle body surface.

i.

Using a heat light, heat the vehicle body surface.

Heating Temperature:
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)
Roof Drip Side Moulding 20 to 30°C (68 to 86°F)


CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat vehicle body and roof drip side moulding or excessively.



ii.

Remove any remaining double-sided tape from the vehicle body.


iii.

Wipe off any tape adhesive residue with cleaner.

NOTICE:
·

Installing the roof drip side moulding with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.





b.

Using a heat light, heat the vehicle body and a new roof drip side moulding.

Heating Temperature:
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)
Roof Drip Side Moulding 20 to 30°C (68 to 86°F)


CAUTION:
·

Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat vehicle body and roof drip side moulding or excessively.



c.

Remove the release paper from the roof drip side moulding.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



d.

Engage the clips to install the roof drip side moulding.

B612710C01
3.427,0.646 3.021,0.406 true 2.802,0.292 3.021,0.5 0.219,0.208 10 true *a
*a Double-sided Tape - -


HINT:

Press the roof drip side moulding firmly to install it.



e.

Remove the protective tape.