Home › Engine / Hybrid System › CRUISE CONTROL › FRONT CAMERA › from 2020.09
RM36W0E _51 Engine / Hybrid System _088664 CRUISE CONTROL _0422124 FRONT CAMERA A

CRUISE CONTROL  FRONT CAMERA  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are replaced during forward recognition camera removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*When only removing and installing the forward recognition camera, it is not necessary to perform forward recognition camera optical axis learning.

Forward recognition camera Adjust forward recognition camera
·

Dynamic Radar Cruise Control System

·

Front Camera System

·

Lane Tracing Assist System

·

Road Sign Assist System

·

Pre-collision System

·

Auto High Beam System


One Time Recognition:
(Click here)
or
Sequential Recognition:
(Click here)
or
Driving Adjustment:
(Click here)
ECU security key Vehicle control history (RoB) are stored (Click here)

NOTICE:
·

When replacing the forward recognition camera, replace it with a new one.

·

Do not touch the camera lens or the front windshield glass in front of the camera.

·

If the forward recognition camera has been struck or dropped, replace it with a new one.

·

When replacing the windshield glass of a vehicle equipped with a forward recognition camera, make sure to use a Lexus genuine part. If a non-Lexus genuine part is used, the forward recognition camera may not be able to be installed due to a missing bracket. Also, the dynamic radar cruise control system, front camera system, lane tracing assist system, road sign assist system, pre-collision system or auto high beam system may not operate properly due to a difference in the transmissivity or black ceramic border.



PROCEDURE

Hide 86466E 1.REMOVE NO. 2 FORWARD RECOGNITION COVER

a.

for 5 Door:

i.
A464274C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Pull the No. 2 forward recognition cover in the direction indicated by the arrow (1) shown in the illustration to disengage the claws.

NOTICE:

If these claws are disengaged separately, they may break. Insert a molding remover between them and pull it down to disengage the claws simultaneously.



ii.

Pull the No. 2 forward recognition cover in the direction indicated by the arrow (2) shown in the illustration to disengage the guides and remove the No. 2 forward recognition cover.



b.

for 3 Door:

i.
B590343C01
0,0 0,0 false
V100135

Slide


Slide the No. 2 forward recognition cover to disengage the claws.

NOTICE:

While holding the No. 1 forward recognition cover, disengage the claws.



ii.
B590344C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Pull the No. 2 forward recognition cover in the direction indicated by the arrow (1) shown in the illustration.


iii.

Pull the No. 2 forward recognition cover in the direction indicated by the arrow (2) shown in the illustration to disengage the guides and remove the No. 2 forward recognition cover.



Hide 86466D 2.REMOVE NO. 1 FORWARD RECOGNITION COVER

a.

for 5 Door:

i.
A464275C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the clips and guides to remove the No. 1 forward recognition cover as shown in the illustration.

NOTICE:

To avoid damaging the guides, always slide the No. 1 forward recognition cover parallel to the windshield glass.




b.

for 3 Door:

i.
B590345C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Pull the No. 1 forward recognition cover in the direction indicated by the arrow (1) shown in the illustration to disengage the clips and guides.

NOTICE:

To avoid damaging the No. 1 forward recognition cover, disengage the clips and guides without hitting the inner rear view mirror.



ii.

Remove the No. 1 forward recognition cover in the direction indicated by the arrow (2) shown in the illustration.



Hide 86464A 3.REMOVE FORWARD RECOGNITION LATCH

a.
A464276C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Disengage the claws and guides to remove the forward recognition latch as shown in the illustration.


Hide 8646C 4.REMOVE FORWARD RECOGNITION CAMERA

NOTICE:

If the forward recognition camera has been struck or dropped, replace it with a new one.


a.
A464277C01
0,0 0,0 false
V113147

Remove in this Direction


Disconnect the connector.

NOTICE:

Do not pull the harness forcibly when disconnecting the connector.



b.

Disengage the guides and remove the forward recognition camera as shown in the illustration.

NOTICE:
·

Do not touch the camera lens.

·

If the forward recognition camera bracket is deformed or damaged, replace it together with the windshield glass.