Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW REGULATOR MOTOR (for 3 Door Front Side) › from 2020.09
RM36W0E _59 Vehicle Exterior _088018 WINDOW / GLASS _0447336 POWER WINDOW REGULATOR MOTOR(for 3 Door Front Side) G

WINDOW / GLASS  POWER WINDOW REGULATOR MOTOR(for 3 Door Front Side)  INSPECTION  


CAUTION / NOTICE / HINT

NOTICE:
·

Do not apply positive (+) auxiliary battery voltage to any terminals, except terminal K7-2 (B) or L7-2 (B), to avoid damaging the pulse sensor inside the motor.

·

Perform initialization of the power window system after removing, inspecting or replacing the power window regulator motor assembly.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION



PROCEDURE

Hide 85710E 1.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

a.

Connect a positive (+) auxiliary battery lead to connector terminal K7-2 (B).

B586050C01
4.583,0.646 4.938,0.833 0.354,0.188 2.563,1.833 3.229,1.833 true 4.188,1.333 4.604,1.333 true 4.927,1.333 5.344,1.333 true 4.969,1.646 5.24,1.927 true 4.177,1.917 4.563,1.646 true 3.823,0.552 4.073,0.729 0.25,0.177 10 false *a 3.26,1.75 3.573,1.906 0.313,0.156 10 false *b 4.083,1.271 4.24,1.469 0.156,0.198 10 false B 5.385,1.26 5.802,1.51 0.417,0.25 10 false GND 5.271,1.917 5.771,2.167 0.5,0.25 10 false DOWN 4.042,1.927 4.375,2.177 0.333,0.25 10 false UP 4.667,0.677 4.917,0.854 0.25,0.177 10 false K7
*a Component without harness connected
(Power Window Regulator Motor Assembly RH)
*b Motor Gear
V100135

Clockwise
V100136

Counterclockwise


NOTICE:

Do not connect a positive (+) auxiliary battery lead to any terminals other than terminal K7-2 (B) to avoid damaging the pulse sensor inside the motor.



b.

Connect a negative (-) auxiliary battery lead to connector terminals K7-1 (GND) and K7-7 (DOWN) or K7-10 (UP).


c.

Check that the motor gear rotates smoothly as follows:

OK:
Measurement Condition Specified Condition
1.

Connect the positive (+) auxiliary battery lead to terminal K7-2 (B), connect a negative (-) auxiliary battery lead to terminal K7-1 (GND), and keep them connected for 3 seconds or more.

2.

With terminals K7-2 (B) and K7-1 (GND) connected, connect a negative (-) auxiliary battery lead to terminal K7-10 (UP).


Motor gear rotates clockwise
1.

Connect a positive (+) auxiliary battery lead to terminal K7-2 (B), connect a negative (-) auxiliary battery lead to terminal K7-1 (GND), and keep them connected for 3 seconds or more.

2.

With terminals K7-2 (B) and K7-1 (GND) connected, connect a negative (-) auxiliary battery lead to terminal K7-7 (DOWN).


Motor gear rotates counterclockwise


If the result is not as specified, replace the power window regulator motor assembly RH.



Hide 85720D 2.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

a.

Connect a positive (+) auxiliary battery lead to connector terminal L7-2 (B).

B586051C01
2.281,0.667 2.625,0.854 0.344,0.188 3.979,1.823 4.646,1.823 true 2.583,1.333 3,1.333 true 1.854,1.333 2.271,1.333 true 2.635,1.646 2.896,2.01 true 1.917,2.01 2.24,1.646 true 1.49,0.521 1.802,0.677 0.313,0.156 10 false *a 3.802,1.75 4.115,1.906 0.313,0.156 10 false *b 3.052,1.26 3.51,1.458 0.458,0.198 10 false GND 1.729,1.26 2.188,1.458 0.458,0.198 10 false B 2.917,2.021 3.375,2.219 0.458,0.198 10 false DOWN 1.75,2.021 2.208,2.219 0.458,0.198 10 false UP 2.365,0.688 2.823,0.885 0.458,0.198 10 false L7
*a Component without harness connected
(Power Window Regulator Motor Assembly LH)
*b Motor Gear
V100135

Counterclockwise
V100136

Clockwise


NOTICE:

Do not connect a positive (+) auxiliary battery lead to any terminals other than terminal L7-2 (B) to avoid damaging the pulse sensor inside the motor.



b.

Connect a negative (-) auxiliary battery lead to connector terminals L7-1 (GND) and L7-7 (DOWN) or L7-10 (UP).


c.

Check that the motor gear rotates smoothly as follows:

OK:
Measurement Condition Specified Condition
1.

Connect a positive (+) auxiliary battery lead to terminal L7-2 (B), connect a negative (-) auxiliary battery lead to terminal L7-1 (GND), and keep them connected for 3 seconds or more.

2.

With terminals L7-2 (B) and L7-1 (GND) connected, connect a negative (-) auxiliary battery lead to terminal L7-10 (UP).


Motor gear rotates counterclockwise
1.

Connect a positive (+) auxiliary battery lead to terminal L7-2 (B), connect a negative (-) auxiliary battery lead to terminal L7-1 (GND), and keep them connected for 3 seconds or more.

2.

With terminals L7-2 (B) and L7-1 (GND) connected, connect a negative (-) auxiliary battery lead to terminal L7-7 (DOWN).


Motor gear rotates clockwise


If the result is not as specified, replace the power window regulator motor assembly LH.