1.REMOVE BACK DOOR OUTSIDE GARNISH SUB-ASSEMBLY
85110R
2.REMOVE REAR WIPER MOTOR ASSEMBLY
81570
3.REMOVE CENTER STOP LIGHT SET
4.REMOVE REAR SPOILER ASSEMBLY (w/ Rear Spoiler)
68131
5.REMOVE BACK DOOR GLASS
Disconnect each connector and disengage each clamp.
|
Protective Tape |
Apply protective tape to the area around the installation position of the back door glass on the back door panel to prevent it from being scratched.
| *a | Matchmark |
Place matchmarks on the back door glass and back door panel at the locations indicated in the illustration.
Matchmarks are not necessary if the back door glass is not going to be reused.
| *a | Piano Wire |
Pass a piano wire between the back door panel and back door glass from the interior.
Tie both wire ends to wooden blocks or similar objects that can serve as handles.
Cut the adhesive by pulling the piano wire around the back door glass.
When separating the back door glass, take care not to damage the paint or interior and exterior ornaments.
When cutting the adhesive, take care not to damage the connectors on the back door glass.
Do not pull the piano wire in a vertical direction, but pull it in a horizontal direction.
Using suction cups, disengage the No. 1 back window glass spacer and No. 2 back window glass spacer to remove the back door glass.
To prevent the back door glass from falling when performing this operation, be sure to hold the back door glass using suction cups.
Be careful not to drop the back door glass.
Leave as much adhesive on the back door panel as possible when removing the back door glass.
64813B
6.REMOVE BACK WINDOW GLASS ADHESIVE DAM
When reusing the back door glass:
| *a | Back Side of Back Door Glass |
Using a scraper, remove the back window glass adhesive dam.
Be careful not to damage the back door glass.
Be sure to replace the back window glass adhesive dam with a new one.
64813B
7.REMOVE NO. 2 BACK WINDOW GLASS ADHESIVE DAM
When reusing the back door glass:
| *a | Back Side of Back Door Glass |
Using a scraper, remove the No. 2 back window glass adhesive dam.
Be careful not to damage the back door glass.
Be sure to replace the No. 2 back window glass adhesive dam with a new one.
75574C
8.REMOVE NO. 1 BACK WINDOW OUTSIDE MOULDING LH
When reusing the back door glass:
| *a | Back Side of Back Door Glass |
Using a scraper, remove the No. 1 back window outside moulding LH.
Be careful not to damage the back door glass.
Be sure to replace the No. 1 back window outside moulding LH with a new one.
75573G
9.REMOVE NO. 1 BACK WINDOW OUTSIDE MOULDING RH
Use the same procedure as for the LH side.
64828B
10.REMOVE BACK WINDOW GLASS CLIP LH
When reusing the back door glass:
| *a | Back Side of Back Door Glass |
|
Adhesive Tape |
Apply adhesive tape to the glass at the edges of the back window glass clip LH as shown in the illustration to mark the installation position of the back window glass clip LH.
Because the adhesive tape will be used to position the back window glass clip LH during installation, do not remove the adhesive tape.
Using a scraper, remove the back window glass clip LH.
Be careful not to damage the back door glass.
Be sure to replace the back window glass clip LH with a new one.
64827B
11.REMOVE BACK WINDOW GLASS CLIP RH
Use the same procedure as for the LH side.
62785F
12.REMOVE BACK DOOR GLASS SPACER
When reusing the back door glass:
| *a | Back Side of Back Door Glass |
Using a scraper, remove the 2 back door glass spacers.
Be careful not to damage the back door glass.
Be sure to replace the back door glass spacer with a new one.