Home › Vehicle Exterior › WINDOW / GLASS › BACK DOOR GLASS (for 3 Door) › from 2020.09
RM36W0E _59 Vehicle Exterior _088018 WINDOW / GLASS _0447340 BACK DOOR GLASS(for 3 Door) A

WINDOW / GLASS  BACK DOOR GLASS(for 3 Door)  INSTALLATION  


PROCEDURE

Hide 68131 1.CLEAN BACK DOOR GLASS

a.

When reusing the back door glass:

i.
B106929

Using a scraper, remove any remaining adhesive residue from the back window glass.

NOTICE:

Be careful not to damage the back door glass.




b.

Clean the outer circumference of the back door glass with a non-residue solvent.

NOTICE:
·

Do not touch the back window glass surface after cleaning it.

·

Even if using a new back door glass, clean it with a non-residue solvent.




Hide 62785F 2.INSTALL BACK DOOR GLASS SPACER

a.

Using a brush or sponge, coat the installation area of the 2 back door glass spacers with glass primer.

NOTICE:
·

Do not apply too much glass primer.

·

Allow the glass primer to dry for 3 minutes or more.

·

Throw away any leftover glass primer.



HINT:

If an area other than specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.



b.

Install 2 new back door glass spacers to the back door glass as shown in the illustration.

B590325C01
1.115,1.219 1.26,0.969 1.26,0.969 1.135,0.656 true 0.875,1.219 0.656,0.875 0.656,0.875 0.885,0.646 true 6.469,1.229 6.667,0.917 6.667,0.917 6.469,0.656 true 6.219,1.219 6.083,0.938 6.083,0.938 6.219,0.656 true 1.802,0.177 2.115,0.375 0.313,0.198 10 false *a 1.292,0.885 1.51,1.063 0.219,0.177 10 true *b 0.458,0.781 0.635,0.958 0.177,0.177 10 true *b 6.688,0.833 6.875,1.021 0.188,0.188 10 true *b 5.875,0.854 6.063,1.042 0.188,0.188 10 true *b
*a Back Side of Back Door Glass *b Ag Print Mark



Hide 64828B 3.INSTALL BACK WINDOW GLASS CLIP LH

a.

Using a brush or sponge, coat the installation area of the back window glass clip LH with glass primer.

NOTICE:
·

Do not apply too much glass primer.

·

Allow the glass primer to dry for 3 minutes or more.

·

Throw away any leftover glass primer.



HINT:

If an area other than specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.



b.

Install a new back window glass clip LH to the back door glass as shown in the illustration.

B590326C01
5.302,1.083 5.063,0.99 5.063,0.99 5.271,0.708 true 5.667,1.083 5.927,0.969 5.927,0.969 5.656,0.719 true 4.844,0.906 5.063,1.104 0.219,0.198 10 true *b 5.938,0.875 6.188,1.052 0.25,0.177 10 true *b 0.448,0.26 0.76,0.458 0.313,0.198 10 false *a
*a Back Side of Back Door Glass *b Ag Print Mark



Hide 64827B 4.INSTALL BACK WINDOW GLASS CLIP RH

HINT:

Use the same procedure as for the LH side.


Hide 75574C 5.INSTALL NO. 1 BACK WINDOW OUTSIDE MOULDING LH

a.

Using a brush or sponge, coat the installation area of the No. 1 back window outside moulding LH with glass primer.

NOTICE:
·

Do not apply too much glass primer.

·

Allow the glass primer to dry for 3 minutes or more.

·

Throw away any leftover glass primer.



HINT:

If an area other than specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.



b.

Install a new back window outside moulding LH to the back door glass as shown in the illustration.

B590327C01
5.646,0.781 5.771,0.469 true 6.021,2.479 5.729,2.333 true 0.365,0.698 0.677,0.854 0.313,0.156 10 false *a 6.063,2.406 6.375,2.563 0.313,0.156 10 false *b 5.729,0.281 6.042,0.438 0.313,0.156 10 false *b 6.24,0.448 6.552,0.604 0.313,0.156 10 false a 6.302,0.708 6.615,0.865 0.313,0.156 10 false b 6.125,1.75 6.438,1.906 0.313,0.156 10 false c 6.292,1.969 6.604,2.125 0.313,0.156 10 false c
*a Back Side of Back Door Glass *b Ag Print Mark


Standard Dimension:
Area Dimension
a 0 to 1.0 mm (0 to 0.0394 in.)
b 0 to 2.0 mm (0 to 0.0787 in.)
c 0 to 3.0 mm (0 to 0.118 in.)



Hide 75573G 6.INSTALL NO. 1 BACK WINDOW OUTSIDE MOULDING RH

HINT:

Use the same procedure as for the LH side.


Hide 64813B 7.INSTALL BACK WINDOW GLASS ADHESIVE DAM

a.

Using a brush or sponge, coat the installation area of the back window glass adhesive dam with glass primer.

NOTICE:
·

Do not apply too much glass primer.

·

Allow the glass primer to dry for 3 minutes or more.

·

Throw away any leftover glass primer.



HINT:

If an area other than specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.



b.

Install a new back window glass adhesive dam to the back door glass as shown in the illustration.

B590328C01
0.698,1.26 0.865,1.156 true 6.26,1.146 6.448,1.25 true 2.135,1.094 2.448,1.25 0.313,0.156 10 false *a 0.49,1.208 0.677,1.354 0.188,0.146 10 true *b 6.49,1.198 6.677,1.344 0.188,0.146 10 true *b
*a Back Side of Back Door Glass *b Ag Print Mark



Hide 64813B 8.INSTALL NO. 2 BACK WINDOW GLASS ADHESIVE DAM

a.

Using a brush or sponge, coat the installation area of the No. 2 back window glass adhesive dam with glass primer.

NOTICE:
·

Do not apply too much glass primer.

·

Allow the glass primer to dry for 3 minutes or more.

·

Throw away any leftover glass primer.



HINT:

If an area other than specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.



b.

Install a new No. 2 back window glass adhesive dam to the back door glass as shown in the illustration.

B590329C01
1.156,2.115 1.344,2.188 true 5.813,2.177 6.01,2.063 true 1.427,0.073 1.74,0.229 0.313,0.156 10 false *a 0.927,2.01 1.125,2.167 0.198,0.156 10 true *b 6.042,1.948 6.24,2.104 0.198,0.156 10 true *b
*a Back Side of Back Door Glass *b Ag Print Mark



Hide 68131 9.INSTALL BACK DOOR GLASS

a.

Clean and shape the contact surface of the vehicle body.

i.
B590330C01
0,0 0,0 false
V100155

Adhesive


Using a knife, cut away excess adhesive on the contact surface of the vehicle body as shown in the illustration.

NOTICE:

Leave as much adhesive on the vehicle body as possible.




b.

Back door glass preliminary installation procedures:

i.

Install the suction cups to the back door glass.


ii.

Temporarily place the back door glass onto the vehicle body and set it so that the gap between the body and upper portion and sides of the back door glass is even.



c.

Position the back door glass.

i.

Using suction cups, place the back door glass in the correct position.


ii.

Check that the whole contact surface of the back door glass rim is perfectly even.


iii.
B590317C01
1.469,0.719 1.448,1.156 1.448,1.156 1.646,1.021 true 1.323,1.167 1.552,1.354 0.229,0.188 10 true *a
*a Matchmark
V100155

Protective Tape


Align the matchmarks on the back door glass and back door panel.

NOTICE:

Check that the back window glass clip LH and back window glass clip RH are engaged to the back door panel correctly.



iv.

Remove the back door glass.



d.

Using a brush, coat the installation surfaces on the back door panel with body primer.

NOTICE:
·

Do not coat the adhesive with body primer.

·

Do not apply too much body primer.

·

Allow the body primer to dry for 3 minutes or more.

·

Throw away any leftover body primer.



HINT:

If an area other than specified is coated by accident, wipe off the body primer with a clean piece of cloth before it dries.



e.

Using a brush or sponge, coat the adhesive application area with glass primer.

B590331C01
5.719,1.917 5.927,1.875 false 4.958,0.802 5.156,0.865 false 4.792,0.729 5.104,0.885 0.313,0.156 10 false *1 5.99,1.792 6.302,1.948 0.313,0.156 10 false *2 0.125,1.031 0.438,1.188 0.313,0.156 10 false *a 1.792,2.052 1.948,2.208 0.156,0.156 10 true B 1.823,1.052 1.938,1.219 0.115,0.167 10 false A 1.823,1.438 1.958,1.594 0.135,0.156 10 true A 1.813,2.406 1.969,2.563 0.156,0.156 10 false B 0.438,1.021 0.594,1.177 0.156,0.156 10 false C 0.74,1.094 0.906,1.271 0.167,0.177 10 true C 4.656,0.302 4.969,0.458 0.313,0.156 10 false A-A 4.385,1.406 4.698,1.563 0.313,0.156 10 false B-B 3.969,2.198 4.281,2.354 0.313,0.156 10 false C-C 4.823,2.292 4.979,2.458 0.156,0.167 10 false c 5.302,1.406 5.458,1.563 0.156,0.156 10 false b 5.458,0.385 5.615,0.542 0.156,0.156 10 false a 5.896,3.292 6.052,3.458 0.156,0.167 10 false d
*1 Back Window Glass Adhesive Dam *2 No. 2 Back Window Glass Adhesive Dam
*a Back Side of Back Door Glass - -
V100155

Glass Primer - -


Standard Dimension:
Area Dimension
a 11 mm (0.433 in.) or more
b 11 mm (0.433 in.) or more
c 22.5 mm (0.886 in.) or more
d 48.1 mm (1.894 in.)


NOTICE:
·

Do not apply too much glass primer.

·

Allow the glass primer to dry for 3 minutes or more.

·

Throw away any leftover glass primer.



HINT:

If an area other than specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.



f.

Apply adhesive to the back door glass.

Adhesive:

Toyota Genuine Windshield Glass Adhesive (High modulus type) or equivalent


i.
B214800C28
1.198,0.438 1.385,0.5 false 0.5,0.625 0.656,0.823 0.156,0.198 10 false a 1.344,1.365 1.5,1.563 0.156,0.198 10 false a 1.115,0.885 1.271,1.083 0.156,0.198 10 false b 0.76,1 0.917,1.198 0.156,0.198 10 false b 1.406,0.438 1.646,0.615 0.24,0.177 10 false *a
*a Nozzle
V100155

Adhesive


Cut off the tip of the cartridge nozzle as shown in the illustration.

Standard Dimension:
Area Dimension
a 12 to 15 mm (0.472 to 0.591 in.)
b 8.0 to 11 mm (0.315 to 0.433 in.)




g.

Load the sealer gun with the cartridge.


h.

Apply adhesive to the back door glass as shown in the illustration.

B590332C01
5.156,0.885 5.073,0.708 false 5.708,1.938 5.917,1.792 false 4.906,0.594 5.219,0.75 0.313,0.156 10 false *1 5.958,1.667 6.271,1.823 0.313,0.156 10 false *2 0.219,0.76 0.531,0.917 0.313,0.156 10 false *a 1.813,1.125 1.969,1.281 0.156,0.156 10 false A 1.802,1.458 1.917,1.625 0.115,0.167 10 true A 1.813,2.458 1.99,2.698 0.177,0.24 10 false B 1.792,2.073 1.948,2.229 0.156,0.156 10 true B 0.771,1.146 0.906,1.313 0.135,0.167 10 true C 0.417,1.042 0.573,1.198 0.156,0.156 10 false C 4.521,0.156 4.844,0.323 0.323,0.167 10 false A-A 4.49,1.313 4.813,1.479 0.323,0.167 10 false B-B 4.156,2.448 4.479,2.615 0.323,0.167 10 false C-C 5.167,0.292 5.323,0.448 0.156,0.156 10 false a 5.75,1.271 5.906,1.427 0.156,0.156 10 false b 5.802,3.344 5.958,3.5 0.156,0.156 10 false c
*1 Back Window Glass Adhesive Dam *2 No. 2 Back Window Glass Adhesive Dam
*a Back Side of Back Door Glass - -
V100155

Adhesive - -


Standard Dimension:
Area Dimension
a 19.6 mm (0.772 in.)
b 29.1 mm (1.15 in.)
c 55.1 mm (2.17 in.)



i.

Install the back door glass.

i.
B590317C01
1.469,0.719 1.448,1.156 1.448,1.156 1.646,1.021 true 1.323,1.167 1.552,1.354 0.229,0.188 10 true *a
*a Matchmark


Using suction cups, position the back door glass so that the matchmarks are aligned, and press it in gently along the rim.

NOTICE:
·

Check that the back window glass clip LH and back window glass clip RH are engaged to the back door panel correctly.

·

Check the clearance between the back door panel and back door glass.




ii.

Lightly press the outer surface of the back door glass to ensure a close fit and engage the back window glass clip LH and back window glass clip RH.

HINT:

Press the glass with force of 98 N (10 kgf, 22.0 lbf) or more.




j.

Using a scraper, remove any excess or protruding adhesive.


k.

Hold the back door glass using protective tape until the applied adhesive becomes hard.

HINT:

Follow the instructions supplied by the adhesive manufacturer or in the corresponding instruction manual for the minimum amount of time necessary to wait before driving the vehicle.



l.

Connect each connector and engage each clamp.


Hide 11.INSTALL BACK DOOR OUTSIDE GARNISH SUB-ASSEMBLY

Hide 12.INSPECT FOR LEAK

a.

After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.


b.

If water leaks into the cabin, allow the water to dry and add adhesive.


c.

Remove the protective tape.