Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM › from 2020.09
RM36W0E _58 Vehicle Interior _087476 THEFT DETERRENT / KEYLESS ENTRY _0434686 THEFT DETERRENT SYSTEM D

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  SYSTEM DESCRIPTION  


OUTLINE OF THEFT DETERRENT SYSTEM


·

The theft deterrent system can be set by locking the doors using any of the following operations:

-

Entry lock operation*1

-

Wireless lock operation

*1: w/ Entry and Start System



·

In the armed state, the alarm function will be activated if one of the following conditions is met:

-

Any of the doors are unlocked.

-

Any of the doors or the engine hood is opened.

-

The intrusion sensor (theft warning ultrasonic sensor) detects movement inside the cabin.*1

-

The glass breakage sensor detects that glass is broken.*1

*1: w/ Intrusion Sensor



·

In the alarm sounding state, the system blinks the turn signal lights. At the same time, the system sounds the vehicle horns and security horn assembly*1 or theft warning siren assembly*2 to deter break-in and theft as well as to warn people around the vehicle.

*1: w/o Intrusion Sensor

*2: w/ Intrusion Sensor


·

The theft deterrent system can be canceled by unlocking the doors using the following operation:

-

Entry unlock operation*1

-

Wireless unlock operation

-

Key linked lock operation

*1: w/ Entry and Start System



·

The theft deterrent system has an active arming mode. There are 4 states in this mode: a disarmed state, an arming preparation state, an armed state and an alarm sounding state.


a.

Disarmed state:

·

The alarm function is not operating.

·

The theft deterrent system is not operating.



b.

Arming preparation state:

·

The time until the system goes into the armed state.

·

The theft deterrent system is not operating.



c.

Armed state:

·

The theft deterrent system is operating.



d.

Alarm sounding state:

·

The alarm function is operating.


Alarm time:

Approximately 27.5 seconds


Alarm Methods
Alarm Method Turn Signal Lights Blinking
Vehicle Horns Sounding
(approximately 0.4-second cycles)
Security Horn Assembly*1 Sounding
(approximately 0.4-second cycles)
Theft Warning Siren Assembly*2 Sounding

*1: w/o Intrusion Sensor

*2: w/ Intrusion Sensor




FUNCTION OF MAIN COMPONENTS


Component Function
Security indicator light Informs driver of theft deterrent system status.
·

Security horn assembly*1

·

Theft warning siren assembly*2


Sounds when attempted break-in or theft is detected.
Turn signal lights Blink when attempted break-in or theft is detected.
Vehicle horns Sound when attempted break-in or theft is detected.
·

Front door courtesy light switch assembly LH/RH

·

Rear door courtesy light switch assembly LH/RH*1


Detects door status (open or closed).
Door unlock detection switch Detects door status (locked or unlocked).
Hood lock assembly (engine hood courtesy switch) Detects engine hood status (open or closed).
Back door lock assembly (back door courtesy light switch) Detects back door status (open or closed).
Intrusion sensor cancel switch*2 Sends a signal to the main body ECU (multiplex network body ECU) to cancel the intrusion sensor (theft warning ultrasonic sensor).
Certification ECU (smart key ECU assembly)*3
·

Receives wireless door lock/unlock signal.

·

Receives entry door lock/unlock signal.


Main body ECU (multiplex network body ECU)*4 Receives wireless door lock/unlock signal.
Intrusion sensor (theft warning ultrasonic sensor)*2 Sends a signal to the main body ECU (multiplex network body ECU) to sound the alarm when detecting an intrusion.
Glass breakage sensor*2 Sounds alarm when the quarter window assembly LH/RH or back door glass is broken, or when there is short in the wire harness.

*1: for 5 Door

*2: w/ Intrusion Sensor

*3: w/ Entry and Start System

*4: w/o Entry and Start System



ACTIVE ARMING MODE (w/o Wireless Door Lock Buzzer Answer-back Function)


a.

Active arming mode:

This system operates as described in the diagram below when one of the items for each condition is met.

HINT:

The term "all doors" used in this section refers to the driver door, front passenger door, rear door LH*, rear door RH* and back door.

*: for 5 Door




E446734E01
3.021,0.656 4.156,0.833 1.135,0.177 10 false Disarmed State 0.542,1.969 1.146,2.896 0.604,0.927 10 false All doors and the engine hood is closed. 3.865,1.958 4.885,2.313 1.021,0.354 10 false The engine hood is opened. 1.438,1.146 2.208,1.344 0.771,0.198 10 false [1] 2.135,2.26 2.906,2.458 0.771,0.198 10 false [3] 1.448,3.198 2.219,3.396 0.771,0.198 10 false [5] 4.01,2.438 4.781,2.635 0.771,0.198 10 false [6] 2.99,3.042 3.76,3.24 0.771,0.198 10 false [4] 5.583,1.135 6.354,1.333 0.771,0.198 10 false [2] 4.844,2.25 5.615,2.448 0.771,0.198 10 false [3] 6.26,6.302 7.031,6.5 0.771,0.198 10 false [12] 5.563,5.26 6.333,5.458 0.771,0.198 10 false [10] 4.781,6.385 5.552,6.583 0.771,0.198 10 false [11] 4.417,5.26 5.188,5.458 0.771,0.198 10 false [7] 3.938,4.5 4.708,4.698 0.771,0.198 10 false [12] 2.167,6.375 2.938,6.573 0.771,0.198 10 false [9] 1.438,5.26 2.208,5.458 0.771,0.198 10 false [8] 0.875,4.813 1.646,5.01 0.771,0.198 10 false [7] 4.281,2.708 6.292,2.896 2.01,0.188 10 false Arming Preparation State (2) 1.49,4.771 2.542,5 1.052,0.229 10 false Armed State (1) 2.99,6.823 4.479,7.115 1.49,0.292 10 false Alarm Sounding State 5.552,3.188 6.323,3.385 0.771,0.198 10 false [5] 0.854,6.854 1.625,7.052 0.771,0.198 10 false [7] 6.229,4.177 7,4.375 0.771,0.198 10 false [12] 6.229,2.115 7,2.313 0.771,0.198 10 false [12] 1.146,2.698 3.156,2.885 2.01,0.188 10 false Arming Preparation State (1) 4.656,4.76 5.708,4.99 1.052,0.229 10 false Armed State (2)

w/ Entry and Start System
Condition Item
Condition [1] In disarmed state, when the ignition switch is off, the system state is switched if the following condition is met:
·

With all doors and the engine hood closed, all doors are locked by wireless operation or entry operation.


Condition [2] In disarmed state, when the ignition switch is off, the system state is switched if the following condition is met:
·

With all doors and the engine hood opened, all doors are locked by wireless operation or entry operation.


Condition [3] One of the following conditions is met:
·

All doors are unlocked by wireless operation, entry operation or key linked lock operation.

·

Any door is unlocked.

·

Any door is opened.

·

The power switch is pushed. (for HV Model)

·

The engine switch is pushed. (for Gasoline Model)

·

The ignition switch is turned to ACC or ON.

·

The auxiliary battery is reconnected.


Condition [4]
·

The engine hood is opened.


Condition [5]
·

Allow approximately 30 seconds to elapse.


Condition [6]
·

The engine hood is closed.


Condition [7] One of the following conditions is met:
·

for Gasoline Model:

The ignition switch is turned to ON and the engine is running at 550 rpm for 2 seconds or more.

·

for HV Model:

The ignition switch is turned to ON (READY).

·

All doors are unlocked by wireless operation, entry operation or key linked lock operation.


Condition [8] One of the following conditions is met:
·

The engine hood is opened when the engine hood is closed.

·

The intrusion sensor (theft warning ultrasonic sensor) detects movement within the vehicle.*1

·

The glass breakage sensor detects that glass is broken.*1

·

Any door is opened when all doors are closed.

·

Any door is unlocked when all doors are locked not by wireless operation or entry operation.

·

When 5 seconds or more have elapsed after the power switch is pressed, the ignition switch is turned from off to ON without pressing the power switch. (for HV Model)

·

When 5 seconds or more have elapsed after the engine switch is pressed, the ignition switch is turned from off to ON without pressing the engine switch. (for Gasoline Model)

·

The auxiliary battery is reconnected when the engine hood is open, any door is open or any door is unlocked.

·

The ignition switch is ON.

·

After warning, engine hood remains open.

·

After warning, any door remains open.

·

After warning, ignition switch ON (IG).


NOTICE:

Ultrasonic waves are used to detect intrusion. Ultrasonic waves do not penetrate steel or glass. When any of the door windows is left open, ultrasonic waves may escape. This may result in the detection of people in the surroundings, leaves or insects entering the vehicle, strong wind or other ultrasonic wave sources in the environment when the vehicle is parked with the door windows open. When parking the vehicle with the door windows open for ventilation, turn off the intrusion sensor (theft warning ultrasonic sensor) using the intrusion sensor cancel switch.*1


Condition [9] If both of the following conditions are met, the alarm stops and the system returns to Armed State (1).
·

After warning time of 27.5 seconds + warning waiting time of 5 seconds elapses.

·

The engine hood was opened prior to the alarm condition.


Condition [10] One of the following conditions is met:
·

The engine hood is opened when the engine hood is closed.*2

·

The intrusion sensor (theft warning ultrasonic sensor) detects movement within the vehicle.*1

·

The glass breakage sensor detects that glass is broken.*1

·

Any door is opened when all doors are closed.

·

Any door is unlocked when all doors are locked not by wireless operation or entry operation.

·

When 5 seconds or more have elapsed after the power switch is pressed, the ignition switch is turned from off to ON without pressing the power switch. (for HV Model)

·

When 5 seconds or more have elapsed after the engine switch is pressed, the ignition switch is turned from off to ON without pressing the engine switch. (for Gasoline Model)

·

The auxiliary battery is reconnected when the engine hood is open, any door is open or any door is unlocked.*2

·

The ignition switch is ON.

·

After warning, engine hood remains open.

·

After warning, any door remains open.

·

After warning, ignition switch ON (IG).


NOTICE:

Ultrasonic waves are used to detect intrusion. Ultrasonic waves do not penetrate steel or glass. When any of the door windows is left open, ultrasonic waves may escape. This may result in the detection of people in the surroundings, leaves or insects entering the vehicle, strong wind or other ultrasonic wave sources in the environment when the vehicle is parked with the door windows open. When parking the vehicle with the door windows open for ventilation, turn off the intrusion sensor (theft warning ultrasonic sensor) using the intrusion sensor cancel switch.*1


Condition [11] If both of the following conditions are met, the alarm stops and the system returns to Armed State (2).
·

After warning time of 27.5 seconds + warning waiting time of 5 seconds elapses.

·

The engine hood was closed before the alarm condition.


Condition [12]
·

The engine hood is closed when the engine hood is opened.



*1: w/ Intrusion Sensor


HINT:

*2: If close before auto alarm set or close during auto alarm set.


w/o Entry and Start System
Condition Item
Condition [1] In disarmed state 1, when the ignition switch is off, the system state is switched if the following condition is met when the key is not in the key cylinder:
·

With all doors and the engine hood closed, all doors are locked by wireless operation.


Condition [2] In disarmed state 1, when the ignition switch is off, the system state is switched if the following condition is met when the key is not in the key cylinder:
·

With all doors and the engine hood opened, all doors are locked by wireless operation.


Condition [3] One of the following conditions is met:
·

All doors are unlocked by wireless operation or key linked lock operation.

·

Any door is unlocked.

·

Any door is opened.

·

The ignition switch is turned to ACC or ON.

·

The auxiliary battery is reconnected.

·

The key is in the ignition key cylinder.


Condition [4]
·

The engine hood is opened.


Condition [5]
·

Allow approximately 30 seconds to elapse.


Condition [6]
·

The engine hood is closed.


Condition [7] One of the following conditions is met:
·

for Gasoline Model:

The ignition switch is turned to ON and the engine is running at 550 rpm for 2 seconds or more.

·

for HV Model:

The ignition switch is turned to ON (READY).

·

All doors are unlocked by wireless operation or key linked lock operation.


Condition [8] One of the following conditions is met:
·

The engine hood is opened when the engine hood is closed.

·

Any door is opened when all doors are closed.

·

Any door is unlocked when all doors are locked not by wireless operation.

·

The auxiliary battery is reconnected when the engine hood is open, any door is open or any door is unlocked.

·

The ignition switch is turned to ON when the key is not in the key cylinder.

·

After warning, engine hood remains open.

·

After warning, any door remains open.

·

After warning, ignition switch ON (IG).


Condition [9] If both of the following conditions are met, the alarm stops and the system returns to Armed State (1).
·

After warning time of 27.5 seconds + warning waiting time of 5 seconds elapses.

·

The engine hood was opened prior to the alarm condition.


Condition [10] One of the following conditions is met:
·

The engine hood is opened when the engine hood is closed.

·

Any door is opened when all doors are closed.

·

Any door is unlocked when all doors are locked not by wireless operation.

·

The auxiliary battery is reconnected when the engine hood is open, any door is open or any door is unlocked.

·

The ignition switch is ON.

·

After warning, engine hood remains open.

·

After warning, any door remains open.

·

After warning, ignition switch ON (IG).


Condition [11] If both of the following conditions are met, the alarm stops and the system returns to Armed State (2).
·

After warning time of 27.5 seconds + warning waiting time of 5 seconds elapses.

·

The engine hood was closed before the alarm condition.


Condition [12]
·

The engine hood is closed when the engine hood is opened.



HINT:

*1: If close before auto alarm set or close during auto alarm set.




ACTIVE ARMING MODE (w/ Wireless Door Lock Buzzer Answer-back Function)


a.

Active arming mode:

This system operates as described in the diagram below when one of the items for each condition is met.

HINT:
·

The term "all doors" used in this section refers to the driver door, front passenger door, and back door.



E452936E01
3.146,0.635 5.292,0.833 2.146,0.198 10 false Disarmed State 1.229,2.76 2.448,3.198 1.219,0.438 10 false Arming Preparation State (1) 4.365,2.76 5.667,3.177 1.302,0.417 10 false Arming Preparation State (2) 1.594,4.74 2.896,5.156 1.302,0.417 10 false Armed State (1) 4.667,4.74 5.969,5.156 1.302,0.417 10 false Armed State (2) 1.708,5.625 3.177,6.167 1.469,0.542 10 false Pre Alarm Sounding State (1) 4.833,6.302 6.302,6.844 1.469,0.542 10 false Pre Alarm Sounding State (2) 2.844,8.146 5.198,8.438 2.354,0.292 10 false Alarm Sounding State 0.458,1.927 1.74,2.417 1.281,0.49 10 false All doors and engine hood is closed. 3.885,1.917 4.927,2.333 1.042,0.417 10 false The engine hood is opened. 1.542,1.094 1.958,1.323 0.417,0.229 10 false [1] 2.083,2.479 2.5,2.708 0.417,0.229 10 false [3] 4.781,1.104 5.198,1.333 0.417,0.229 10 false [2] 5.302,2.49 5.719,2.719 0.417,0.229 10 false [3] 4.052,2.74 4.469,2.969 0.417,0.229 10 false [6] 3,3.052 3.417,3.281 0.417,0.229 10 false [4] 1.833,3.417 2.25,3.646 0.417,0.229 10 false [5] 2.313,5.177 2.729,5.406 0.417,0.229 10 false [8] 0.938,4.604 1.354,4.833 0.417,0.229 10 false [7] 0.958,5.188 1.375,5.417 0.417,0.229 10 false [9] 0.729,5.719 1.146,5.948 0.417,0.229 10 false [7] 3.01,5.396 3.427,5.625 0.417,0.229 10 false [10] 2.25,6.292 2.667,6.521 0.417,0.229 10 false [11] 1.5,7.677 1.917,7.906 0.417,0.229 10 false [12] 0.854,8.031 1.271,8.26 0.417,0.229 10 false [7] 5.01,3.406 5.427,3.635 0.417,0.229 10 false [5] 5.448,5.198 5.865,5.427 0.417,0.229 10 false [8] 4.021,4.604 4.438,4.833 0.417,0.229 10 false [15] 3.979,5.031 4.396,5.26 0.417,0.229 10 false [7] 4.104,5.302 4.521,5.531 0.417,0.229 10 false [13] 4.01,6.365 4.427,6.594 0.417,0.229 10 false [15] 4.927,6.948 5.344,7.177 0.417,0.229 10 false [7] 5.719,6.958 6.135,7.188 0.417,0.229 10 false [11] 4.667,7.677 5.083,7.906 0.417,0.229 10 false [14] 6.375,7.802 6.792,8.031 0.417,0.229 10 false [15] 6.083,6.021 6.406,6.292 0.323,0.271 10 false [10] 5.896,4.073 6.313,4.302 0.417,0.229 10 false [15] 6.375,2.625 6.792,2.854 0.417,0.229 10 false [15] 0.479,0.188 2.625,0.385 2.146,0.198 10 false Disarmed State

w/ Entry and Start System
Condition Item
Condition [1] In disarmed state, when the ignition switch is off, the system state is switched if the following condition is met:
·

With all doors, the engine hood and back door closed, all doors are locked by wireless operation, entry operation or key linked power door lock operation.

·

With all doors, the engine hood and back door closed, the state changes from any of the doors being opened to all doors being closed.


Condition [2] In disarmed state, when the ignition switch is off, the system state is switched if the following condition is met:
·

With all doors and engine hood closed open, all doors are locked by wireless operation, entry operation, or key linked power door lock operation.

·

With engine hood closed the state changes from any of the doors being opened to all doors being closed.


Condition [3] One of the following conditions is met:
·

All doors and the engine hood are unlocked by wireless operation, entry operation or key linked power door lock operation.

·

Any door is unlocked.

·

Any door is opened.

·

The engine switch is pushed.

·

The ignition switch is turned ACC or ON (IG).

·

The auxiliary battery is reconnected.


Condition [4] One of the following conditions is met:
·

The engine hood open.


Condition [5]
·

Allow approximately 30 seconds to elapse.


Condition [6] Both of the following conditions are met:
·

The engine hood close.


Condition [7] One of the following conditions is met:
·

The ignition switch is turned to ON and the engine is running at 550 rpm for 2 seconds or more.

·

All doors are unlocked by wireless operation, entry operation or keylinked power door lock operation.

·

The ignition switch is turned ACC or ON (IG) within 5 seconds after the engine switch is pushed.


Condition [8]
·

The door is unlocked by operating the mechanical keys.


Condition [9] One of the following conditions is met:
·

The engine hood is opened when the engine hood is closed.

·

Any door is opened when all doors are closed.

·

Any door is unlocked when all doors are locked not by wireless operation, entry operation or key linked power door lock operation.

·

When 5 seconds or more have elapsed after the ignition switch is pressed, the ignition switch is turned from off to ON (IG) without pressing the ignition switch.

·

The auxiliary battery is reconnected when the engine hood is open, any door is open or any door is unlocked.


Condition [10] The ignition switch is ON (IG), ACC and one of the following conditions is met:
·

With all doors, the engine hood and back door closed, all doors are locked by wireless operation, entry operation or key linked power door lock operation.

·

With all doors and the engine hood closed the state changes from any of the doors being opened to all doors being closed.


Condition [11]
·

Allow approximately 10 seconds to elapse.


Condition [12] If both of the following conditions are met, the alarm stops and the system returns to Armed State (1).
·

Allow approximately 27.5 seconds to elapse.

·

The engine hood was closed prior to the alarm condition.


Condition [13] One of the following conditions is met:
·

The engine hood is opened when the engine hood is closed.*1

·

Any door is opened when all doors are closed.

·

Any door is unlocked when all doors are locked not by wireless operation, entry operation or key linked power door lock operation.

·

When 5 seconds or more have elapsed after the ignition switch is pressed, the ignition switch is turned from off to ON (IG) without pressing the ignition switch.

·

The auxiliary battery is reconnected when the engine hood is open*1, any door is open or any door is unlocked.


Condition [14] If both of the following conditions are met, the alarm stops and the system returns to Armed State (2).
·

Allow approximately 27.5 seconds to elapse.

·

The engine hood was opened before the alarm condition.


Condition [15] Close engine hood.

HINT:

*1: If close before auto alarm set or close during auto alarm set.


w/o Entry and Start System
Condition Item
Condition [1] In disarmed state, when the ignition switch is off, the system state is switched if the following condition is met when the key is not in the key cylinder:
·

With all doors, the engine hood and back door closed, all doors are locked by wireless operation or key linked power door lock operation.

·

With all doors, the engine hood and back door closed, the state changes from any of the doors being opened to all doors being closed.


Condition [2] In disarmed state, when the ignition switch is off, the system state is switched if the following condition is met when the key is not in the key cylinder:
·

With all doors and engine hood closed open, all doors are locked by wireless operation or key linked power door lock operation.

·

With engine hood closed the state changes from any of the doors being opened to all doors being closed.


Condition [3] One of the following conditions is met:
·

All doors and the engine hood are unlocked by wireless operation or key linked power door lock operation.

·

Any door is unlocked.

·

Any door is opened.

·

The ignition switch is turned ACC or ON (IG).

·

The auxiliary battery is reconnected.

·

The key is in the ignition key cylinder.


Condition [4] One of the following conditions is met:
·

The engine hood open.


Condition [5]
·

Allow approximately 30 seconds to elapse.


Condition [6] Both of the following conditions are met:
·

The engine hood close.


Condition [7] One of the following conditions is met:
·

The ignition switch is turned to ON and the engine is running at 550 rpm for 2 seconds or more.

·

All doors are unlocked by wireless operation, entry operation or keylinked power door lock operation.

·

The key is in the ignition key cylinder.

·

The ignition switch is turned ACC or ON (IG).


Condition [8]
·

The door is unlocked by operating the mechanical keys.


Condition [9] One of the following conditions is met:
·

The engine hood is opened when the engine hood is closed.

·

Any door is opened when all doors are closed.

·

Any door is unlocked when all doors are locked not by wireless operation or key linked power door lock operation.

·

The auxiliary battery is reconnected when the engine hood is open, any door is open or any door is unlocked.

·

The ignition switch is turned to ON when the key is not in the key cylinder.


Condition [10] The ignition switch is ON (IG), ACC and one of the following conditions is met when the key is not in the key cylinder:
·

With all doors, the engine hood and back door closed, all doors are locked by wireless operation or key linked power door lock operation.

·

With all doors and the engine hood closed the state changes from any of the doors being opened to all doors being closed.


Condition [11]
·

Allow approximately 10 seconds to elapse.


Condition [12] If both of the following conditions are met, the alarm stops and the system returns to Armed State (1).
·

Allow approximately 27.5 seconds to elapse.

·

The engine hood was closed prior to the alarm condition.


Condition [13] One of the following conditions is met:
·

The engine hood is opened when the engine hood is closed.*1

·

Any door is opened when all doors are closed.

·

Any door is unlocked when all doors are locked not by wireless operation, entry operation or key linked power door lock operation.

·

The auxiliary battery is reconnected when the engine hood is open*1, any door is open or any door is unlocked.

·

The ignition switch is turned to ON when the key is not in the key cylinder.


Condition [14] If both of the following conditions are met, the alarm stops and the system returns to Armed State (2).
·

Allow approximately 27.5 seconds to elapse.

·

The engine hood was opened before the alarm condition.


Condition [15] Close engine hood.

HINT:

*1: If close before auto alarm set or close during auto alarm set.




FORCED DOOR LOCK CONTROL


a.

The forced door lock control prevents the vehicle from being tampered with. Immediately after a door is unlocked (armed state), all doors are forced to lock by a forced door lock signal.

i.

If the following conditions are met, the forced door lock control is operated.

·

The key is not in the key cylinder.

·

The theft deterrent system is in the armed state.

·

Any door is unlocked.





INTRUSION SENSOR (THEFT WARNING ULTRASONIC SENSOR) (w/ Intrusion Sensor)


NOTICE:

Ultrasonic waves are used to detect intrusion. Ultrasonic waves do not penetrate steel or glass. When any of the door windows is left open, ultrasonic waves may escape. This may result in the detection of people in the surroundings, leaves or insects entering the vehicle, strong wind or other ultrasonic wave sources in the environment when the vehicle is parked with the door windows open. When parking the vehicle with the door windows open for ventilation, turn off the intrusion sensor (theft warning ultrasonic sensor) using the intrusion sensor cancel switch.


a.

The main body ECU (multiplex network body ECU) activates the intrusion sensor (theft warning ultrasonic sensor) when the system changes from the disarmed state to the armed preparation state. If an intrusion detection signal is input from the intrusion sensor (theft warning ultrasonic sensor) during the armed state, the main body ECU (multiplex network body ECU) changes to the alarm sounding state in order to output an alarm.


b.

When the system is in the disarmed state, the function of the intrusion Sensor (theft warning ultrasonic sensor) can be disabled by pressing the intrusion sensor cancel switch.


c.

The intrusion sensor (theft warning ultrasonic sensor) may erroneously detect intrusion in the following states:

·

Persons or pets are in the vehicle.

·

The vehicle is parked in a place where extreme vibrations or noises occur, such as in a parking garage.

·

Ice or snow is removed from the vehicle, causing the vehicle to receive repeated impacts or vibrations.

·

The wind or something similar causes an externally mounted reflectively coated windshield cover to move.

·

The intrusion sensor (theft warning ultrasonic sensor) may react to a hanger or other objects hanging in the cabin when they drop or swing.

·

The system changes to the armed state even when any of the windows is open. The intrusion Sensor (theft warning ultrasonic sensor) may react to objects moving outside the vehicle when any of the windows is open.

·

The vehicle is inside an automatic or high-pressure car wash.

·

The vehicle experiences impacts, such as hail, lightning strikes and other kinds of repeated impacts or vibrations.




CHECK INTRUSION SENSOR (THEFT WARNING ULTRASONIC SENSOR) (w/ Intrusion Sensor)


a.

Turn the ignition switch off.


b.

Make sure all of the windows, doors and the engine hood are closed.


c.

Lock all of the doors through wireless operation or the entry lock function and check that the security indicator light illuminates (system changes to the arming preparation state).


d.

Approximately 30 seconds after locking all of the doors through wireless operation or the entry lock function, check that the security indicator light is blinking (system is in the armed state). Then, check that the alarm function operates (system changes to the alarm sounding state) due to movement inside the vehicle.

HINT:

If the electrical key transmitter sub-assembly is within an exterior detection area, the intrusion sensor (theft warning ultrasonic sensor) will not operate.



e.

Perform an unlock operation using the wireless or entry operation to stop the alarm.



CHECK INTRUSION SENSOR CANCEL SWITCH (THEFT WARNING ULTRASONIC SENSOR) (w/ Intrusion Sensor)


a.

Turn the ignition switch off.


b.

Make sure all of the windows, doors and the engine hood closed.


c.

Press the intrusion sensor cancel switch (theft warning ultrasonic sensor) and check that the message is displayed on the multi-information display.


d.

Lock all of the doors through wireless operation, the entry lock function or key linked power door lock operation and check that the security indicator light illuminates (system changes to the arming preparation state).


e.

Approximately 30 seconds after locking all of the doors through wireless operation, the entry lock function or key linked power door lock operation, check that the security indicator light is blinking (system is in the armed state). Then, check that the alarm function does not operate (system does not change to alarm sounding state) due to movement inside the vehicle.

HINT:
·

Even if the intrusion sensor (theft warning ultrasonic sensor) is off, the theft deterrent system will be in the armed state. Therefore, if any of the doors is manually unlocked, the alarm will operate.

·

If the electrical key transmitter sub-assembly is within an exterior detection area, the intrusion sensor (theft warning ultrasonic sensor) will not operate.





THEFT WARNING SIREN ASSEMBLY (w/ Intrusion Sensor)


a.

The theft warning siren assembly has an internal battery. If power to the theft warning siren assembly is interrupted or the communication line is open, the theft warning siren assembly detects it and sounds the alarm using the internal battery.


b.

The theft warning siren assembly has the following alarm controls: normal alarm control and open circuit alarm control. Under normal alarm control, the alarm sounds based on instructions from the main body ECU (multiplex network body ECU) whereas under open circuit alarm control, the theft warning siren assembly judges current security conditions and sounds the alarm by itself.

i.

Normal alarm control

The theft warning siren assembly sounds when the theft deterrent system is in the alarm sounding state and does not sound when the system is not in the alarm sounding state.

HINT:

If communication interruption between the theft warning siren assembly and main body ECU (multiplex network body ECU) continues for 70 seconds or more while the theft deterrent system is in the alarm sounding state, the theft warning siren assembly stops sounding.



ii.
B315877E02
0.083,0.083 2.979,0.458 2.896,0.375 10 false Conditions of theft warning siren assembly 1.292,0.875 2.26,1.125 0.969,0.25 10 false Disarmed State 1.385,2.219 2.323,2.469 0.938,0.25 10 false Armed State 0.958,1.667 1.104,1.813 0.146,0.146 10 false *1 2.448,1.677 2.729,1.854 0.281,0.177 10 false *2 0.458,3.177 2.99,3.531 2.531,0.354 10 false *1: Theft deterrent system changes to the armed state. 0.479,3.938 3.031,4.323 2.552,0.385 10 false *2: Theft deterrent system changes to the disarmed state.

Open circuit alarm control

The theft warning siren assembly changes between the disarmed state and armed state in accordance with the theft deterrent system changes between the disarmed state and armed state. If the power source, ground or communication line is open while the theft warning siren assembly is in the armed state, the theft warning siren assembly sounds.

During the open circuit alarm sounding state, the theft warning siren assembly sounds intermittently for 28 seconds and then stops for 5 seconds. This pattern repeats a maximum of 9 times.

The intermittent sound will stop when either condition is met:
1.

The theft warning siren changes to the disarmed state.

2.

The open circuit is returned to normal.


B267215E15
0.063,0.083 3.781,0.302 3.719,0.219 10 false (a) Intermittent sound pattern repeats a maximum of 9 times 0.229,0.427 2.74,0.635 2.51,0.208 10 false Theft warning siren is in the armed state 1.854,1.25 2.76,1.49 0.906,0.24 10 false Circuit is open 1.729,1.76 2.75,2 1.021,0.24 10 false Circuit is normal 1.031,2.063 3.469,2.302 2.438,0.24 10 false Theft warning siren sounds 0.729,2.573 2.802,2.823 2.073,0.25 10 false Theft warning siren sounds stop 1.854,8.031 2.76,8.271 0.906,0.24 10 false Circuit is open 1.729,8.552 2.75,8.781 1.021,0.229 10 false Circuit is normal 1.031,8.854 3.281,9.083 2.25,0.229 10 false Theft warning siren sounds 0.729,9.365 2.76,9.615 2.031,0.25 10 false Theft warning siren sounds stop 0.063,0.917 2.729,1.146 2.667,0.229 10 false Theft warning siren is in the disarmed state 0.26,7.219 2.75,7.438 2.49,0.219 10 false Theft warning siren is in the armed state 0.063,7.708 2.729,7.938 2.667,0.229 10 false Theft warning siren is in the disarmed state 1.854,4.719 2.76,4.927 0.906,0.208 10 false Circuit is open 1.729,5.229 2.75,5.469 1.021,0.24 10 false Circuit is normal 1.031,5.531 3.375,5.75 2.344,0.219 10 false Theft warning siren sounds 0.729,6.052 2.75,6.302 2.021,0.25 10 false Theft warning siren sounds stop 0.26,3.896 2.76,4.146 2.5,0.25 10 false Theft warning siren is in the armed state 0.063,4.396 2.74,4.604 2.677,0.208 10 false Theft warning siren is in the disarmed state 4.74,0.083 5.833,0.281 1.094,0.198 10 false T1: 28 seconds 3.344,2.417 3.531,2.563 0.188,0.146 10 false T1 3.531,2.885 3.719,3.031 0.188,0.146 10 false T2 3.333,5.885 3.521,6.031 0.188,0.146 10 false T1 3.333,9.188 3.521,9.333 0.188,0.146 10 false T1 3.531,9.656 3.719,9.802 0.188,0.146 10 false T2 6.052,0.083 6.948,0.344 0.896,0.26 10 false T2: 5 seconds 0.063,3.229 2.604,3.458 2.542,0.229 10 false (b) The open circuit is returned to normal 0.219,3.5 4.073,3.729 3.854,0.229 10 false (1) The open circuit is returned to normal within 28 seconds 0.219,6.792 4.948,7.021 4.729,0.229 10 false (2) The open circuit is returned to normal after 28 seconds or more elapsed




SECURITY INDICATOR LIGHT OUTPUT


a.

According to the state of the theft deterrent system, the main body ECU (multiplex network body ECU) outputs a signal to turn the security indicator light on. However, some of the actual lighting conditions of the security indicator light are different from the output signals of the main body ECU (multiplex network body ECU).

Output
State of Theft Deterrent System Security Indicator Light
Output Signal from Main Body ECU (Multiplex Network Body ECU) Actual Lighting Condition
Disarmed state Off
·

Off (Immobiliser function unset)

·

Blinking (Immobiliser function set)


Arming preparation state (1), (2) On On
Armed state (1), (2) Off Blinking (Immobiliser function set)
Alarm sounding state On On

Blinking Cycle
Time Security Indicator Light
0.125 seconds On
1.875 seconds Off

HINT:

When the immobiliser function is set, the security indicator light blinks during both the disarmed state and the armed state due to output signals from the immobiliser function.