CHECK POWER DISTRIBUTION BOX ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
| *1 | Power Distribution Box Assembly | *2 | Main Body ECU (Multiplex Network Body ECU) |
Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.
Reconnect the power distribution box assembly connector.
Measure the voltage and resistance according to the value(s) in the table below.
Measure the values on the wire harness side with the connectors connected.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| MB-13 (GND1) - Body ground | Ground | Always | Below 1 Ω |
| MB-14 (GND2) - Body ground | Ground | Always | Below 1 Ω |
| MB-26 (BECU) - Body ground | Auxiliary battery power supply | Ignition switch off | 11 to 14 V |
| MB-27 (IGR) - Body ground | IG power supply | Ignition switch ON | 11 to 14 V |
Install the main body ECU (multiplex network body ECU) to the power distribution box assembly.
Measure the voltage and check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| 4E-5 (FRCY) - Body ground | Front door courtesy light switch (for RH) input | Front door RH open | Below 1 V |
| Front door RH closed | 11 to 14 V | ||
| 4E-3 (FLCY) - Body ground | Front door courtesy light switch (for LH) input | Front door LH open | Below 1 V |
| Front door LH closed | 11 to 14 V | ||
| 4E-1 (RCTY) - Body ground*1 | Rear door courtesy light switch (for RH) input | Rear door RH open | Below 1 V |
| Rear door RH closed | Pulse generation | ||
| 4E-26 (LCTY) - Body ground*1 | Rear door courtesy light switch (for LH) input | Rear door LH open | Below 1 V |
| Rear door LH closed | Pulse generation | ||
| 4E-2 (BCTY) - Body ground | Back door courtesy light switch input | Back door closed | Below 1 V |
| Back door open | 11 to 14 V | ||
| H4-3 (LSFR) - Body ground | Front door RH unlock detection switch input | Front door RH unlocked | Below 1 V |
| Front door RH locked | Pulse generation | ||
| H4-9 (LSFL) - Body ground | Front door LH unlock detection switch input | Front door LH unlocked | Below 1 V |
| Front door LH locked | Pulse generation | ||
| H5-23 (LSWR) - Body ground*1 | Rear door RH unlock detection switch input | Rear door RH unlocked | Below 1 V |
| Rear door RH locked | Pulse generation | ||
| H4-10 (LSWL) - Body ground*1 | Rear door LH unlock detection switch input | Rear door LH unlocked | Below 1 V |
| Rear door LH locked | Pulse generation | ||
| H4-28 (L2) - Body ground | Driver door key-linked lock input | Driver door key cylinder turned to lock | Below 1 V |
| H4-28 (L2) - Body ground | Driver door key-linked lock input | Driver door key cylinder not turned | Pulse generation |
| H4-4 (UL3) - Body ground | Driver door key-linked unlock input | Driver door key cylinder turned to unlock | Below 1 V |
| H4-4 (UL3) - Body ground | Driver door key-linked unlock input | Driver door key cylinder not turned | Pulse generation |
| H4-27 (HCTY) - Body ground | Engine hood courtesy switch input signal | Back door closed (OFF) → open (ON) | 10 kΩ or higher → Below 1 Ω |
| H4-16 (KSW) - Body ground*2 | Unlock warning switch input | Key not in key cylinder (OFF) → Key in key cylinder (ON) | 10 kΩ or higher → Below 1 Ω |
| H4-7 (IND) - Body ground*2 | Security indicator illumination | Security indicator light illuminated (Theft deterrent system in alarm sounding state) | Pulse generation → Below 2 V |
| 4D-4 (SH) - Body ground*3 | Security horn drive | Security horn sounding (Theft deterrent system is in alarm sounding state) | Pulse generation (Below 1 V ←→ 11 to 14 V) |
| 4B-43 (HORN) - Body ground | Vehicle horn drive | Vehicle horns sounding (Theft deterrent system is in alarm sounding state) | Pulse generation (Below 1 V ←→ 11 to 14 V) |
| 4D-11 (HORN) - Body ground | |||
| H5-8 (GPBS) - Body ground*4 | Glass breakage sensor signal | Glass breakage sensor normal | Below 2 V |
| Glass breakage sensor malfunctioning | 4.5 to 14 V | ||
| H5-16 (SSCL) - Body ground*4 | Theft warning siren assembly drive | Theft warning siren assembly sounding (Theft deterrent system is in alarm sounding state) | Pulse generation (Below 1 V ←→ 11 to 14 V) |
| H5-20 (SSW1) - Body ground*4 | Intrusion sensor cancel switch signal | Intrusion sensor cancel switch on | Below 1 V |
| Intrusion sensor cancel switch off | Pulse generation | ||
| H5-11 (LIN4) - Body ground*4 | LIN communication line | LIN communication line | Pulse generation |
*1: for 5 Door
*2: w/o Entry and Start System
*3: w/ Security Horn Assembly
*4: w/ Intrusion Sensor