Home › Engine / Hybrid System › G16E-GTS (ENGINE MECHANICAL) › CYLINDER HEAD › from 2020.09
RM36W0E _51 Engine / Hybrid System _095252 G16E-GTS ENGINE MECHANICAL _0447815 CYLINDER HEAD A

G16E-GTS ENGINE MECHANICAL  CYLINDER HEAD  DISASSEMBLY  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during cylinder head removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Cylinder head sub-assembly Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

PROCEDURE

Hide 13711 1.REMOVE INTAKE VALVE

a.
A479865N01
2.344,1.927 1.854,1.979 false 1.667,0.135 1.063,0.438 true 1.5,1.917 1.958,2.115 0.458,0.198 10 false SST 1.719,0.052 2.177,0.25 0.458,0.198 10 false SST

Using SST, compress each compression spring and remove the 6 valve spring retainer locks.

SST
09202-70020  (09202-01010, 09202-01020)
09202-00021  

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



b.

Remove the 6 valve spring retainers, 6 compression springs and 6 intake valves from the cylinder head sub-assembly.

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



Hide 13715 2.REMOVE EXHAUST VALVE

CAUTION:
·

The exhaust valve is filled with sodium. Sodium is a strong alkali which may produce a dangerous chemical reaction. Therefore, be very careful when handling and disposing of it.

·

Do not disassemble the exhaust valve for the following reasons: 1) If sodium enters your eyes, vision loss may occur. 2) If sodium contacts your skin, burns may occur. 3) If sodium is exposed to a flame and starts a fire due to the chemical reaction that takes place, burns may occur.

·

If the exhaust valve is damaged, remove the valve and perform the proper procedures to dispose of the sodium (disposal preparation and actual disposal).

·

When removing a damaged exhaust valve, always wear rubber gloves and safety glasses.

·

Do not cut the exhaust valve to take out the sodium.



HINT:
·

The sodium inside the exhaust valve is safe as long as the sodium is not exposed to air.

·

Exhaust valves filled with sodium can be identified by confirming the "NA" identification mark.



a.
A479843N01
1.427,1.781 1.615,1.99 false 1.885,0.156 2.323,0.24 true 1.677,1.969 2.135,2.167 0.458,0.198 10 false SST 1.573,0.073 2.031,0.271 0.458,0.198 10 false SST

Using SST, compress each compression spring and remove the 6 valve spring retainer locks.

SST
09202-70020  (09202-01010, 09202-01020)
09202-00021  

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



b.

Remove the 6 valve spring retainers, 6 compression springs and 6 exhaust valves from the cylinder head sub-assembly.

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



Hide 3.REMOVE VALVE STEM OIL SEAL

a.
A479844

Using needle-nose pliers, remove the 12 valve stem oil seals.


Hide 4.REMOVE VALVE SPRING SEAT

a.
A479845

Using compressed air and a Magnet Hand, remove the 12 valve spring seats from the cylinder head sub-assembly by blowing air onto them.


Hide 11117E 5.REMOVE NO. 1 STRAIGHT SCREW PLUG

NOTICE:

If coolant leaks from a No. 1 straight screw plug or a plug is corroded, replace it.


A479846

a.

Using a 6 mm straight hexagon wrench, remove the 2 No. 1 straight screw plugs from the cylinder head sub-assembly.


Hide 11117F 6.REMOVE NO. 2 STRAIGHT SCREW PLUG

NOTICE:

If coolant leaks from a No. 2 straight screw plug or a plug is corroded, replace it.


a.
A479847

Using a 10 mm straight hexagon wrench, remove the No. 2 straight screw plug from the cylinder head sub-assembly.


Hide 7.REMOVE STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.


a.
A481101

Using an E8 "TORX" socket wrench, remove the 9 stud bolts.


Hide 8.REMOVE STRAIGHT PIN

NOTICE:

If a straight pin is deformed or its threads are damaged, replace it.


a.
A481102

Remove the 2 straight pin.


Hide 13715 9.DISPOSE OF EXHAUST VALVE

CAUTION:
·

The exhaust valve is filled with sodium. Sodium is a strong alkali which may produce a dangerous chemical reaction. Therefore, be very careful when handling and disposing of it.

·

Do not disassemble the exhaust valve for the following reasons: 1) If sodium enters your eyes, vision loss may occur. 2) If sodium contacts your skin, burns may occur. 3) If sodium is exposed to a flame and starts a fire due to the chemical reaction that takes place, burns may occur.

·

If the exhaust valve is damaged, remove the valve and perform the proper procedures to dispose of the sodium (disposal preparation and actual disposal).

·

When removing a damaged exhaust valve, always wear rubber gloves and safety glasses.

·

Do not cut the exhaust valve to take out the sodium.



NOTICE:

If it is clearly stated that the industrial waste disposal method is dissolution, carry out the process below.


HINT:
·

The sodium inside the exhaust valve is safe as long as the sodium is not exposed to air.

·

Exhaust valves filled with sodium can be identified by confirming the "NA" identification mark.



a.

Waste disposal preparation

CAUTION:

Always carry out the following when performing the disposal procedure.


i.

Have a fire extinguisher close by.


ii.

Wear safety glasses.


iii.

Wear rubber gloves.



b.

Waste disposal

i.

Put on rubber gloves and remove the damaged exhaust valve from the cylinder head.


ii.

Add 10 L of water or more to a large receptacle (a bucket, oil can, etc.) in a well-ventilated area.


iii.

Hold the damaged exhaust valve upright with pliers or large pair of tweezers and submerge it into the water.

CAUTION:
·

Fully submerge the damaged exhaust valve in water.

·

Do not allow any sparks or other flames near the receptacle as hydrogen gas is generated by the chemical reaction.

·

Stay 2 or 3 m or more away from the receptacle as a strong chemical reaction occurs.