Home › Engine / Hybrid System › G16E-GTS (ENGINE MECHANICAL) › CYLINDER BLOCK › 2020.09–2021.11
RM36W0E _51 Engine / Hybrid System _095252 G16E-GTS ENGINE MECHANICAL _0447816 CYLINDER BLOCK A

G16E-GTS ENGINE MECHANICAL  CYLINDER BLOCK  DISASSEMBLY  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during cylinder block removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Piston or piston ring Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

PROCEDURE

Hide 12211 1.REMOVE NO. 1 VENTILATION CASE

CAUTION:

Do not diassembly except if the No. 1 ventilaion case to be damaged.


a.
A479868

Remove the 3 bolts, 2 nuts and No. 1 ventilation case from the cylinder block sub-assembly.


b.
A479869

Remove the 3 oil separator gaskets from the No. 1 ventilation case.


Hide 12581A 2.REMOVE NO. 1 CYLINDER BLOCK INSULATOR

a.
A479870

Remove the No. 1 cylinder block insulator from the cylinder block sub-aseembly.


Hide 3.INSPECT CONNECTING ROD THRUST CLEARANCE

a.
A478728

Using a dial indicator, measure the thrust clearance while moving the connecting rod sub-assembly back and forth.

Standard Thrust Clearance:

0.15 to 0.50 mm (0.00591 to 0.01969 in.)


Maximum Thrust Clearance:

0.50 mm (0.01969 in.)


HINT:

If the thrust clearance is more than the maximum, replace the connecting rod. If necessary, replace the crankshaft.



Hide 4.INSPECT CONNECTING ROD OIL CLEARANCE

a.
A479871C02
0.74,0.615 1.031,0.365 true 1.052,0.229 1.365,0.385 0.313,0.156 10 false *a
*a Alignment Mark


Note the alignment marks on the connecting rod and connecting rod cap so that they can be reinstalled to their original locations.


b.
A479872

Using an SST wrench, remove the 2 connecting rod bolts and connecting rod cap.

SST
09205-16011  

HINT:

Keep the connecting rod bearing and connecting rod cap together.



c.

Clean the crank pin and connecting rod bearing.


d.

Check the crank pin and connecting rod bearing for pitting and scratches.

HINT:

If the crank pin or connecting rod bearing is damaged, replace the connecting rod bearings. If necessary, replace the crankshaft.



e.
A478729C01
1.188,0.906 1.76,0.938 true 1,0.813 1.313,1.01 0.313,0.198 10 false *a
*a Plastigage


Lay a strip of Plastigage on the crank pin.


f.
A478730C01
1.021,0.698 1.667,0.792 true 0.74,0.604 0.969,0.781 0.229,0.177 10 true *a
*a Front Mark


Check that the front mark of the connecting rod cap is facing the correct direction, and install the connecting rod cap to the connecting rod.


g.
A478731

Apply a light coat of engine oil to the threads and under the heads of the 2 connecting rod bolts.


h.

Using an SST, install and alternately tighten the 2 connecting rod bolts in several steps.

SST
09205-16011  

Torque:
50 N*m (510 kgf*cm, 37 ft.*lbf)


i.
A478732C01
2.198,0.552 2.531,0.375 false 1.396,0.427 1.854,0.625 0.458,0.198 10 false *b 2.573,0.271 2.885,0.469 0.313,0.198 10 false *a
*a Paint Mark
*b 90°
V100135

Front of Engine


Mark the front of each connecting rod bolt with paint.


j.

Tighten the connecting rod bolts 90° as shown in the illustration.

NOTICE:

Do not turn the crankshaft during the measurement.



k.

Remove the 2 connecting rod bolts and connecting rod cap.

HINT:

Keep the connecting rod bearing and connecting rod cap together.



l.
A478733C01
1.135,0.677 1.729,0.979 true 1.271,4.146 0.615,3.406 0.615,3.406 1.344,3 true 0.635,3.406 1.396,3.333 true 0.917,0.531 1.115,0.729 0.198,0.198 10 true *a 0.427,3.333 0.74,3.531 0.313,0.198 10 false *b
*a Plastigage
*b 1, 2 or 3 Mark


Measure the Plastigage at its widest point.

Standard Oil Clearance:

0.032 to 0.065 mm (0.00126 to 0.00256 in.)


Maximum Oil Clearance:

0.065 mm (0.00256 in.)


HINT:
·

If the oil clearance is more than the maximum, replace the connecting rod bearings. If necessary, replace the crankshaft.

·

If replacing a connecting rod bearing, select a new one with the same number as marked on the connecting rod cap. There are 3 sizes of standard connecting rod bearings, marked "1", "2" or "3" accordingly.



Standard Connecting Rod Big End Inside Diameter:
Mark Specified Condition
1 51.000 to 51.008 mm (2.00787 to 2.00818 in.)
2 51.008 to 51.016 mm (2.00818 to 2.00850 in.)
3 51.016 to 51.024 mm (2.00850 to 2.00881 in.)


Standard Connecting Rod Bearing Center Wall Thickness:
Mark Specified Condition
1 1.487 to 1.491 mm (0.0585 to 0.0587 in.)
2 1.491 to 1.495 mm (0.0587 to 0.0589 in.)
3 1.495 to 1.499 mm (0.0589 to 0.0590 in.)


Standard Crank Pin Diameter:

47.992 to 48.000 mm (1.88945 to 1.88976 in.)


NOTICE:

Remove the Plastigage completely after the measurement.



m.

Perform the inspection above for each cylinder.


Hide 5.REMOVE PISTON WITH CONNECTING ROD

a.

Using a ridge reamer, remove all the carbon from the top of each cylinder.


b.

Remove the 6 connecting rod bolts, 3 connecting rod caps and 3 connecting rod bearings.


c.

Push the 4 pistons, 4 connecting rods and 4 connecting rod bearings out through the top of the cylinder block sub-assembly.

HINT:
·

Keep the connecting rod bearings, connecting rods and connecting rod caps together.

·

Arrange the removed parts in such a way that they can be reinstalled to their original locations.




Hide 6.REMOVE CONNECTING ROD BEARING

a.

Remove the 6 connecting rod bearings from the 3 connecting rods and 3 connecting rod caps.

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



Hide 7.INSPECT CRANKSHAFT THRUST CLEARANCE

a.
A478735

Using a dial indicator, measure the crankshaft thrust clearance while prying the crankshaft back and forth with a screwdriver.

Standard Thrust Clearance:

0.02 to 0.22 mm (0.000787 to 0.00866 in.)


Maximum Thrust Clearance:

0.22 mm (0.00866 in.)


HINT:

If the thrust clearance is more than the maximum, replace the crankshaft thrust washers as a set. If necessary, replace the crankshaft.


Standard Thrust Washer Thickness:

2.415 to 2.470 mm (0.0951 to 0.0972 in.)



Hide 13411 8.REMOVE CRANKSHAFT

a.
A479873

Uniformly loosen and remove the 8 crankshaft bearing cap set bolts and 10 bolts.


b.
A479874

Remove the crankshaft bearing cap assembly from the cylinder block sub-assembly with a screwdriver with its tip wrapped with protective tape..

HINT:
·

Keep the No. 2 crankshaft bearings and crankshaft bearing caps together.

·

Arrange the removed parts in such a way that they can be reinstalled to their original locations.




c.

Remove the crankshaft from the cylinder block sub-assembly.

HINT:

Keep the crankshaft bearings and crankshaft thrust washers together with the cylinder block sub-assembly.



d.

Check each crankshaft journal and crankshaft bearing for pitting and scratches.

If the journal or crankshaft bearing is damaged, replace the crankshaft bearings. If necessary, replace the crankshaft.


Hide 11791 9.REMOVE CRANKSHAFT THRUST WASHER

a.
A479875

Remove the 2 crankshaft thrust washers from the No. 3 journal position of the cylinder block sub-assembly.


Hide 11711 10.REMOVE CRANKSHAFT BEARING

a.

Remove the 4 No. 1 crankshaft bearings and 4 No. 2 crankshaft bearings from the cylinder block sub-assembly and crankshaft bearing cap assembly.

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



Hide 13011 11.REMOVE PISTON RING SET

a.
A400507C01
1.115,1.76 1.115,1.531 1.115,1.531 1.354,1.281 false 1.063,1.802 1.375,2 0.313,0.198 10 false *a
*a Piston Ring Expander


Using a piston ring expander, remove the No. 1 compression ring and No. 2 compression ring from the piston.


b.

Remove the oil ring expander, upper side rail and lower side rail from the piston by hand.

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



Hide 13101A 12.REMOVE PISTON PIN HOLE SNAP RING

a.
A426847C01
1.885,0.979 2.208,1.188 true 2.104,0.813 2.313,0.375 true 2.25,1.115 2.563,1.271 0.313,0.156 10 false *a 2.344,0.271 2.656,0.427 0.313,0.156 10 false *b
*a Front Mark Cutout Portion
*b Protective Tape


Using a screwdriver, pry out the 2 piston pin hole snap rings from the piston.

HINT:

Tape the screwdriver tip before use.



Hide 13.REMOVE PISTON

a.
A400509

Gradually heat each piston to between 80 and 90°C (176 to 194°F).

CAUTION:

Be sure to wear protective gloves.



b.
A400510

Using a brass bar and a hammer, lightly tap out the piston pin and remove the connecting rod.

HINT:
·

The piston and piston pin are a matched set.

·

Arrange the removed parts in such a way that they can be reinstalled to their original locations.




Hide 15708 14.REMOVE NO. 1 OIL NOZZLE SUB-ASSEMBLY

a.
A479876

Using a 5 mm hexagon wrench, remove the 3 bolts and 3 No. 1 oil nozzle sub-assemblies from the cylinder block sub-assembly.


Hide 15709 15.REMOVE NO. 2 OIL NOZZLE SUB-ASSEMBLY

a.
A479877

Using a 5 mm hexagon wrench, remove the 3 bolts and 3 No. 2 oil nozzle sub-assemblies from the cylinder block sub-assembly.


Hide 1570A 16.REMOVE NO. 3 OIL NOZZLE SUB-ASSEMBLY

a.
A479878

Using a 5 mm hexagon wrench, remove the 3 bolts and 3 No. 3 oil nozzle sub-assemblies from the cylinder block sub-assembly.