87940
1.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH (w/o Mirror Herter)
Check the operation of the retractable mirror.
Disconnect and reconnect the auxiliary battery between each mirror position check.
The mirror position cannot be changed manually when the auxiliary battery is connected. To change the mirror position manually, the auxiliary battery must be disconnected first.
If the motor is kept energized, even after each mirror position check, it may lead to a motor malfunction. Make sure to disconnect the auxiliary battery immediately after performing each mirror position check.
Disconnect the outer rear view mirror assembly LH connector.
| *a | Component without harness connected
(Outer Rear View Mirror Assembly LH) |
For each position: Disconnect the auxiliary battery, set the mirror position by hand, connect the auxiliary battery, and check the retractable mirror movement.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L10-7 (MR) - Auxiliary battery positive (+)
L10-6 (MF) - Auxiliary battery negative (-) |
Forward position (A) | Moves from (A) to (E) |
| L10-6 (MF) - Auxiliary battery positive (+)
L10-7 (MR) - Auxiliary battery negative (-) |
Forward position (A) | Does not move |
| L10-7 (MR) - Auxiliary battery positive (+)
L10-6 (MF) - Auxiliary battery negative (-) |
Position between forward position (A) and driving position (C) | Moves from (B) to (E) |
| L10-6 (MF) - Auxiliary battery positive (+)
L10-7 (MR) - Auxiliary battery negative (-) |
Position between forward position (A) and driving position (C) | Moves from (B) to (A) |
| L10-7 (MR) - Auxiliary battery positive (+)
L10-6 (MF) - Auxiliary battery negative (-) |
Driving position (C) | Moves from (C) to (E) |
| L10-6 (MF) - Auxiliary battery positive (+)
L10-7 (MR) - Auxiliary battery negative (-) |
Driving position (C) | Does not move |
| L10-7 (MR) - Auxiliary battery positive (+)
L10-6 (MF) - Auxiliary battery negative (-) |
Position between driving position (C) and retracted position (E) | Moves from (D) to (E) |
| L10-6 (MF) - Auxiliary battery positive (+)
L10-7 (MR) - Auxiliary battery negative (-) |
Position between driving position (C) and retracted position (E) | Moves from (D) to (C) |
| L10-7 (MR) - Auxiliary battery positive (+)
L10-6 (MF) - Auxiliary battery negative (-) |
Retracted position (E) | Does not move |
| L10-6 (MF) - Auxiliary battery positive (+)
L10-7 (MR) - Auxiliary battery negative (-) |
Retracted position (E) | Moves from (E) to (C) |
If the result is not as specified, replace the outer mirror retractor assembly LH.
Check the operation of the mirror surface.
| *a | Component without harness connected
(Outer Rear View Mirror Assembly LH) |
Apply voltage and check the operation of the outer rear view mirror assembly LH.
| Tester Connection | Specified Condition |
|---|---|
| L10-1 (MV) - Auxiliary battery positive (+)
L10-2 (M+) - Auxiliary battery negative (-) |
Turns upward |
| L10-2 (M+) - Auxiliary battery positive (+)
L10-1 (MV) - Auxiliary battery negative (-) |
Turns downward |
| L10-3 (MH) - Auxiliary battery positive (+)
L10-2 (M+) - Auxiliary battery negative (-) |
Turns right |
| L10-2 (M+) - Auxiliary battery positive (+)
L10-3 (MH) - Auxiliary battery negative (-) |
Turns left |
If the result is not as specified, replace the outer rear view mirror assembly LH.
Check the side turn signal light assembly LH.
| *a | Component without harness connected
(Outer Rear View Mirror Assembly LH) |
Apply auxiliary battery voltage to the terminals of the connector, and check the illumination condition.
| Tester Connection | Specified Condition |
|---|---|
| L10-4 (B) - Auxiliary battery positive (+)
L10-5 (-) - Auxiliary battery negative (-) |
Side turn light illuminates |
If the result is not as specified, inspect the side turn signal light assembly LH or replace the outer rear view mirror assembly LH.
87910
2.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH (w/o Mirror Herter)
Check the operation of the retractable mirror.
Disconnect and reconnect the auxiliary battery between each mirror position check.
The mirror position cannot be changed manually when the auxiliary battery is connected. To change the mirror position manually, the auxiliary battery must be disconnected first.
If the motor is kept energized, even after each mirror position check, it may lead to a motor malfunction. Make sure to disconnect the auxiliary battery immediately after performing each mirror position check.
Disconnect the outer rear view mirror assembly RH connector.
| *a | Component without harness connected
(Outer Rear View Mirror Assembly RH) |
For each position: Disconnect the auxiliary battery, set the mirror position by hand, connect the auxiliary battery, and check the retractable mirror movement.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K10-7 (MR) - Auxiliary battery positive (+)
K10-6 (MF) - Auxiliary battery negative (-) |
Forward position (A) | Moves from (A) to (E) |
| K10-6 (MF) - Auxiliary battery positive (+)
K10-7 (MR) - Auxiliary battery negative (-) |
Forward position (A) | Does not move |
| K10-7 (MR) - Auxiliary battery positive (+)
K10-6 (MF) - Auxiliary battery negative (-) |
Position between forward position (A) and driving position (C) | Moves from (B) to (E) |
| K10-6 (MF) - Auxiliary battery positive (+)
K10-7 (MR) - Auxiliary battery negative (-) |
Position between forward position (A) and driving position (C) | Moves from (B) to (A) |
| K10-7 (MR) - Auxiliary battery positive (+)
K10-6 (MF) - Auxiliary battery negative (-) |
Driving position (C) | Moves from (C) to (E) |
| K10-6 (MF) - Auxiliary battery positive (+)
K10-7 (MR) - Auxiliary battery negative (-) |
Driving position (C) | Does not move |
| K10-7 (MR) - Auxiliary battery positive (+)
K10-6 (MF) - Auxiliary battery negative (-) |
Position between driving position (C) and retracted position (E) | Moves from (D) to (E) |
| K10-6 (MF) - Auxiliary battery positive (+)
K10-7 (MR) - Auxiliary battery negative (-) |
Position between driving position (C) and retracted position (E) | Moves from (D) to (C) |
| K10-7 (MR) - Auxiliary battery positive (+)
K10-6 (MF) - Auxiliary battery negative (-) |
Retracted position (E) | Does not move |
| K10-6 (MF) - Auxiliary battery positive (+)
K10-7 (MR) - Auxiliary battery negative (-) |
Retracted position (E) | Moves from (E) to (C) |
If the result is not as specified, replace the outer mirror retractor assembly RH.
Check the operation of the mirror surface.
| *a | Component without harness connected
(Outer Rear View Mirror Assembly RH) |
Apply voltage and check the operation of the outer rear view mirror assembly RH.
| Tester Connection | Specified Condition |
|---|---|
| K10-1 (MV) - Auxiliary battery positive (+)
K10-2 (M+) - Auxiliary battery negative (-) |
Turns upward |
| K10-2 (M+) - Auxiliary battery positive (+)
K10-1 (MV) - Auxiliary battery negative (-) |
Turns downward |
| K10-3 (MH) - Auxiliary battery positive (+)
K10-2 (M+) - Auxiliary battery negative (-) |
Turns left |
| K10-2 (M+) - Auxiliary battery positive (+)
K10-3 (MH) - Auxiliary battery negative (-) |
Turns right |
If the result is not as specified, replace the outer rear view mirror assembly RH.
Check the side turn signal light assembly RH.
| *a | Component without harness connected
(Outer Rear View Mirror Assembly RH) |
Apply auxiliary battery voltage to the terminals of the connector, and check the illumination condition.
| Tester Connection | Specified Condition |
|---|---|
| K10-4 (B) - Auxiliary battery positive (+)
K10-5 (-) - Auxiliary battery negative (-) |
Side turn light illuminates |
If the result is not as specified, inspect the side turn signal light assembly RH or replace the outer rear view mirror assembly RH.
87940
3.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH (w/ Mirror Herter)
Check the operation of the retractable mirror.
Disconnect and reconnect the auxiliary battery between each mirror position check.
The mirror position cannot be changed manually when the auxiliary battery is connected. To change the mirror position manually, the auxiliary battery must be disconnected first.
If the motor is kept energized, even after each mirror position check, it may lead to a motor malfunction. Make sure to disconnect the auxiliary battery immediately after performing each mirror position check.
| *a | Component without harness connected
(Outer Rear View Mirror Assembly LH) |
Disconnect the outer rear view mirror assembly LH connector.
For each position: Disconnect the auxiliary battery, set the mirror position by hand, connect the auxiliary battery, and check the retractable mirror movement.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L8-3 (MR) - Auxiliary battery positive (+)
L8-11 (MF) - Auxiliary battery negative (-) |
Forward position (A) | Moves from (A) to (E) |
| L8-11 (MF) - Auxiliary battery positive (+)
L8-3 (MR) - Auxiliary battery negative (-) |
Forward position (A) | Does not move |
| L8-3 (MR) - Auxiliary battery positive (+)
L8-11 (MF) - Auxiliary battery negative (-) |
Position between forward position (A) and driving position (C) | Moves from (B) to (E) |
| L8-11 (MF) - Auxiliary battery positive (+)
L8-3 (MR) - Auxiliary battery negative (-) |
Position between forward position (A) and driving position (C) | Moves from (B) to (A) |
| L8-3 (MR) - Auxiliary battery positive (+)
L8-11 (MF) - Auxiliary battery negative (-) |
Driving position (C) | Moves from (C) to (E) |
| L8-11 (MF) - Auxiliary battery positive (+)
L8-3 (MR) - Auxiliary battery negative (-) |
Driving position (C) | Does not move |
| L8-3 (MR) - Auxiliary battery positive (+)
L8-11 (MF) - Auxiliary battery negative (-) |
Position between driving position (C) and retracted position (E) | Moves from (D) to (E) |
| L8-11 (MF) - Auxiliary battery positive (+)
L8-3 (MR) - Auxiliary battery negative (-) |
Position between driving position (C) and retracted position (E) | Moves from (D) to (C) |
| L8-3 (MR) - Auxiliary battery positive (+)
L8-11 (MF) - Auxiliary battery negative (-) |
Retracted position (E) | Does not move |
| L8-11 (MF) - Auxiliary battery positive (+)
L8-3 (MR) - Auxiliary battery negative (-) |
Retracted position (E) | Moves from (E) to (C) |
If the result is not as specified, replace the outer mirror retractor assembly LH.
Check the operation of the mirror surface.
| *a | Component without harness connected
(Outer Rear View Mirror Assembly LH) |
Apply voltage and check the operation of the outer rear view mirror assembly LH.
| Tester Connection | Specified Condition |
|---|---|
| L8-1 (MV) - Auxiliary battery positive (+)
L8-10 (M+) - Auxiliary battery negative (-) |
Turns upward |
| L8-10 (M+) - Auxiliary battery positive (+)
L8-1 (MV) - Auxiliary battery negative (-) |
Turns downward |
| L8-9 (MH) - Auxiliary battery positive (+)
L8-10 (M+) - Auxiliary battery negative (-) |
Turns right |
| L8-10 (M+) - Auxiliary battery positive (+)
L8-9 (MH) - Auxiliary battery negative (-) |
Turns left |
If the result is not as specified, replace the outer rear view mirror assembly LH.
Check the operation of the mirror heater.
| *a | Component without harness connected
(Outer Rear View Mirror Assembly LH) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L8-7 (+) - L8-15 (-) | 25°C | 6.4 to 9.6 Ω |
If the result is not as specified, inspect the outer mirror LH or replace the outer rear view mirror assembly LH.
Connect a cable from the positive (+) auxiliary battery terminal to L8-7 (+) and the negative (-) auxiliary battery terminal to L8-15 (-), then check that the mirror becomes warm.
It takes a short time for the mirror to become warm.
Mirror becomes warm.
If the result is not as specified, inspect the outer mirror LH or replace the outer rear view mirror assembly LH.
Check the side turn signal light assembly LH.
| *a | Component without harness connected
(Outer Rear View Mirror Assembly LH) |
Apply auxiliary battery voltage to the terminals of the connector, and check the illumination condition.
| Tester Connection | Specified Condition |
|---|---|
| L8-16 (B) - Auxiliary battery positive (+)
L8-15 (-) - Auxiliary battery negative (-) |
Side turn light illuminates |
If the result is not as specified, inspect the side turn signal light assembly LH or replace the outer rear view mirror assembly LH.
Check the operation of the blind spot monitor indicator.
Connect 4 new 1.5 V dry-cell batteries in series.
| *a | Component without harness connected
(Outer Rear View Mirror Assembly LH) |
Apply 6 V dry-cell battery voltage to the terminals of the connector, and check the blind spot monitor indicator condition.
| Tester Connection | Specified Condition |
|---|---|
| L8-8 (BSL+) - Positive (+) end of the 6 V dry-cell battery
L8-15 (-) - Negative (-) end of the 6 V dry-cell battery |
Blind spot monitor indicator comes on |
Do not apply a voltage of 6 V or higher.
If the result is not as specified, inspect the outer mirror LH or replace the outer rear view mirror assembly LH.
87910
4.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH (w/ Mirror Herter)
Check the operation of the retractable mirror.
Disconnect and reconnect the auxiliary battery between each mirror position check.
The mirror position cannot be changed manually when the auxiliary battery is connected. To change the mirror position manually, the auxiliary battery must be disconnected first.
If the motor is kept energized, even after each mirror position check, it may lead to a motor malfunction. Make sure to disconnect the auxiliary battery immediately after performing each mirror position check.
| *a | Component without harness connected
(Outer Rear View Mirror Assembly RH) |
Disconnect the outer rear view mirror assembly RH connector.
For each position: Disconnect the auxiliary battery, set the mirror position by hand, connect the auxiliary battery, and check the retractable mirror movement.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K8-3 (MR) - Auxiliary battery positive (+)
K8-11 (MF) - Auxiliary battery negative (-) |
Forward position (A) | Moves from (A) to (E) |
| K8-11 (MF) - Auxiliary battery positive (+)
K8-3 (MR) - Auxiliary battery negative (-) |
Forward position (A) | Does not move |
| K8-3 (MR) - Auxiliary battery positive (+)
K8-11 (MF) - Auxiliary battery negative (-) |
Position between forward position (A) and driving position (C) | Moves from (B) to (E) |
| K8-11 (MF) - Auxiliary battery positive (+)
K8-3 (MR) - Auxiliary battery negative (-) |
Position between forward position (A) and driving position (C) | Moves from (B) to (A) |
| K8-3 (MR) - Auxiliary battery positive (+)
K8-11 (MF) - Auxiliary battery negative (-) |
Driving position (C) | Moves from (C) to (E) |
| K8-11 (MF) - Auxiliary battery positive (+)
K8-3 (MR) - Auxiliary battery negative (-) |
Driving position (C) | Does not move |
| K8-3 (MR) - Auxiliary battery positive (+)
K8-11 (MF) - Auxiliary battery negative (-) |
Position between driving position (C) and retracted position (E) | Moves from (D) to (E) |
| K8-11 (MF) - Auxiliary battery positive (+)
K8-3 (MR) - Auxiliary battery negative (-) |
Position between driving position (C) and retracted position (E) | Moves from (D) to (C) |
| K8-3 (MR) - Auxiliary battery positive (+)
K8-11 (MF) - Auxiliary battery negative (-) |
Retracted position (E) | Does not move |
| K8-11 (MF) - Auxiliary battery positive (+)
K8-3 (MR) - Auxiliary battery negative (-) |
Retracted position (E) | Moves from (E) to (C) |
If the result is not as specified, replace the outer mirror retractor assembly RH.
Check the operation of the mirror surface.
| *a | Component without harness connected
(Outer Rear View Mirror Assembly RH) |
Apply voltage and check the operation of the outer rear view mirror assembly RH.
| Tester Connection | Specified Condition |
|---|---|
| K8-1 (MV) - Auxiliary battery positive (+)
K8-10 (M+) - Auxiliary battery negative (-) |
Turns upward |
| K8-10 (M+) - Auxiliary battery positive (+)
K8-1 (MV) - Auxiliary battery negative (-) |
Turns downward |
| K8-9 (MH) - Auxiliary battery positive (+)
K8-10 (M+) - Auxiliary battery negative (-) |
Turns left |
| K8-10 (M+) - Auxiliary battery positive (+)
K8-9 (MH) - Auxiliary battery negative (-) |
Turns right |
If the result is not as specified, replace the outer rear view mirror assembly RH.
Check the operation of the mirror heater.
| *a | Component without harness connected
(Outer Rear View Mirror Assembly RH) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K8-7 (+) - K8-15 (-) | 25°C | 6.4 to 9.6 Ω |
If the result is not as specified, inspect the outer mirror RH or replace the outer rear view mirror assembly RH.
Connect a cable from the positive (+) auxiliary battery terminal to K8-7 (+) and negative (-) auxiliary battery terminal to K8-15 (-), then check that the mirror becomes warm.
It takes a short time for the mirror to become warm.
Mirror becomes warm.
If the result is not as specified, inspect the outer mirror RH or replace the outer rear view mirror assembly RH.
Check the side turn signal light assembly RH.
| *a | Component without harness connected
(Outer Rear View Mirror Assembly RH) |
Apply auxiliary battery voltage to the terminals of the connector, and check the illumination condition.
| Battery Connection | Specified Condition |
|---|---|
| K8-16 (B) - Auxiliary battery positive (+)
K8-15 (-) - Auxiliary battery negative (-) |
Side turn light illuminates |
If the result is not as specified, inspect the side turn signal light assembly RH or replace the outer rear view mirror assembly RH.
Check the operation of the blind spot monitor indicator.
Connect 4 new 1.5 V dry-cell batteries in series.
| *a | Component without harness connected
(Outer Rear View Mirror Assembly RH) |
Apply 6 V dry-cell battery voltage to the terminals of the connector, and check the blind spot monitor indicator condition.
| Battery Connection | Specified Condition |
|---|---|
| K8-8 (BSR+) - Positive (+) end of the 6 V dry-cell battery
K8-15 (-) - Negative (-) end of the 6 V dry-cell battery |
Blind spot monitor indicator comes on |
Do not apply a voltage of 6 V or higher.
If the result is not as specified, inspect the outer mirror RH or replace the outer rear view mirror assembly RH.