Home › Vehicle Exterior › MIRROR (EXT) › OUTER REAR VIEW MIRROR (for TMC Made 5 Door) › from 2020.09
RM36W0E _59 Vehicle Exterior _088061 MIRROR (EXT) _0447367 OUTER REAR VIEW MIRROR(for TMC Made 5 Door) A

MIRROR (EXT)  OUTER REAR VIEW MIRROR(for TMC Made 5 Door)  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 87966 1.INSTALL OUTER MIRROR RETRACTOR

a.
B576115

Install a new wire harness to a new outer mirror retractor.


b.

Connect the connector.


c.

Install the outer mirror retractor with the 3 screws.


d.

Connect the connector.


e.
B576112

Engage the guide to install the power unit assembly.


f.

Install the 3 screws.


g.

Install the base with the 3 new screws.

NOTICE:
·

Check that the wire harness is not caught.

·

Do not damage the screw coating.

·

Securely tighten the screws so that they will not come loose.




h.
B567820

Engage the guides to install a new gasket.

NOTICE:

Do not make gaps between the base and gasket.



i.

w/o mirror heater:

i.
B576116

Connect each connector to a new adapter.


ii.

Rotate the adapter A and twist the longer wire harness as shown in the illustration.



j.

w/ mirror heater:

i.

Pull the retainer and release the lock of connector housing.

B576117C01
1.198,1.208 1.427,1.531 false 2.833,1.365 2.656,1.052 false 2.677,0.781 2.906,0.438 false 5.833,1.406 6.094,1.042 false 1.458,1.469 1.771,1.667 0.313,0.198 10 false *1 5.677,1.365 5.99,1.563 0.313,0.198 10 false *1 2.875,0.292 3.188,0.49 0.313,0.198 10 false *2 2.823,1.385 3.135,1.583 0.313,0.198 10 false *2 0.198,0.24 0.51,0.438 0.313,0.198 10 false *a 5.375,0.135 5.688,0.333 0.313,0.198 10 false *b 3.469,0.052 3.781,0.25 0.313,0.198 10 false *c
*1 Retainer *2 Terminal
*a Unlock Position *b Lock Position
*c Rear view of connector - -



ii.

While referring to the chart below, insert the terminals of the wire harness into the back of a new connector housing until they lock.

Wire Harness Color
1 2 3 4 5 6 7 8
White - Pink - - - Gray Gray - Red
9 10 11 12 13 14 15 16
Red Black Orange - - - Blue Yellow

NOTICE:
·

When inserting the terminals of the wire harness, compare the new connector with the connector that was cut off during removal and make sure that the arrangement of the wire colors of the terminals is the same as before.

·

If the insertion position of the terminals is mistaken, the vehicle side control system may be damaged.

·

Check that the terminals are securely locked and cannot be removed.




iii.

Push the retainer and lock the connector.



k.
B567828C01
2.333,2.677 2.271,2.875 true 2.417,2.396 2.552,2.604 false 1.906,2.542 2,2.427 false 2.24,2.302 2.438,2.469 0.198,0.167 10 false *1 2.104,2.844 2.302,3.01 0.198,0.167 10 false *b 1.74,2.5 1.927,2.656 0.188,0.156 10 false *2 2.979,1.51 3.156,1.688 0.177,0.177 10 true *a
*1 Wire Harness
*2 Gasket
*a over 40 mm (1.575 in.)
*b Paint Mark


Install the vinyl tape as shown in the illustration.


l.
B576118N01
0.74,3.885 0.896,4.083 0.156,0.198 10 false A 1.594,4.052 1.75,4.25 0.156,0.198 10 false B

While referring to the chart below, install 2 new clips.

Reference Measurement
Area Measurement
A 67 to 77 mm (2.638 to 3.031 in.)
B 215 to 235 mm (8.465 to 9.252 in.)


Hide 87948 2.INSTALL OUTER MIRROR HOLE COVER

a.
B576128

Engage the claws to install a new outer mirror hole cover.


Hide 4.INSTALL OUTER MIRROR LOWER COVER

a.
B576110

Engage the claws to install the outer mirror lower cover.


b.

Install the screw.