Home › General › SPECIFICATIONS › DRIVE SHAFT / PROPELLER SHAFT › 2020.09–2021.11
RM36W0E _V1 General _087262 SPECIFICATIONS _0424139 DRIVE SHAFT / PROPELLER SHAFT F

SPECIFICATIONS  DRIVE SHAFT / PROPELLER SHAFT  SERVICE DATA  


Front Drive Shaft Assembly (for 1KR-FE):
Standard drive shaft length for LH Side 642.7 mm (2.11 ft.)
for RH Side 817.7 mm (2.68 ft.)
Standard front drive shaft damper set dimension for RH Side 470.0 to 474.0 mm (1.54 to 1.55 ft.)
Standard grease capacity Outboard joint 91 to 99 g (3.21 to 3.49 oz)
Inboard joint 114 to 124 g (4.02 to 4.37 oz)


Front Drive Shaft Assembly (for M15A-FKS TMC Made):
Standard drive shaft length (for CVT) for LH Side 594.1 to 604.1 mm (1.95 to 1.98 ft.)
for RH Side 804.1 to 814.1 mm (2.64 to 2.67 ft.)
Standard drive shaft length (for Manual Transaxle) for LH Side 596.9 to 604.9 mm (1.96 to 1.98 ft.)
for RH Side 806.9 to 814.9 mm (2.65 to 2.67 ft.)
Standard front drive shaft damper set dimension (for CVT) for RH Side with Damper 464.0 to 468.0 mm (1.52 to 1.54 ft.)
Standard front drive shaft damper set dimension (for Manual Transaxle) for RH Side 446.5 to 450.5 mm (1.46 to 1.48 ft.)
Standard grease capacity (for CVT) Outboard joint 116 to 126 g (4.09 to 4.44 oz)
Inboard joint 127 to 137 g (4.48 to 4.83 oz)
Standard grease capacity (for Manual Transaxle) Outboard joint 135 to 145 g (4.76 to 5.11 oz)
Inboard joint 168 to 178 g (5.93 to 6.28 oz)


Front Drive Shaft Assembly (for M15A-FKS TMMF Made):
Standard drive shaft length (for CVT) for LH Side 624.1 mm (2.05 ft.)
for RH Side 839.1 mm (2.75 ft.)
Standard drive shaft length (for Manual Transaxle) for LH Side 624.1 mm (2.05 ft.)
for RH Side 837.1 mm (2.75 ft.)
Standard front drive shaft damper set dimension for RH Side 488.0 to 492.0 mm (1.60 to 1.61 ft.)
Standard grease capacity Outboard joint 76 to 86 g (2.68 to 3.03 oz)
Inboard joint 130 to 140 g (4.59 to 4.94 oz)


Front Drive Shaft Assembly (for M15A-FXE TMC Made):
Standard drive shaft length for LH Side 594.1 to 604.1 mm (1.95 to 1.98 ft.)
for RH Side 804.1 to 814.1 mm (2.64 to 2.67 ft.)
Standard front drive shaft damper set dimension for RH Side 464.0 to 468.0 mm (1.52 to 1.54 ft.)
Standard grease capacity Outboard joint 116 to 126 g (4.09 to 4.44 oz)
Inboard joint 127 to 137 g (4.48 to 4.83 oz)


Front Drive Shaft Assembly (for M15A-FXE TMMF Made):
Standard drive shaft length for LH Side 624.1 mm (2.05 ft.)
for RH Side 839.1 mm (2.75 ft.)
Standard front drive shaft damper set dimension for RH Side 481.0 to 485.0 mm (1.58 to 1.59 ft.)
Standard grease capacity Outboard joint 80 to 90 g (2.82 to 3.17 oz)
Inboard joint 130 to 140 g (4.59 to 4.94 oz)


Front Drive Shaft Assembly (for G16E-GTS):
Standard drive shaft length for LH Side 584.2 to 594.2 cm (1.92 to 1.95 ft.)
for RH Side 864.4 to 874.4 cm (2.84 to 2.87 ft.)
Standard front drive shaft dust cover RH set distance for RH Side 58.8 to 59.4 mm (2.31 to 2.34 in.)
Standard grease capacity Outboard joint 105 to 115 g (3.70 to 4.06 oz)
Inboard joint 168 to 178 g (5.93 to 6.28 oz)


Rear Drive Shaft Assembly:
Standard drive shaft length for LH Side 739.4 to 743.4 cm (2.43 to 2.44 ft.)
for RH Side 734.4 to 738.4 cm (2.41 to 2.42 ft.)
Standard grease capacity Inboard joint 134 to 144 g (4.73 to 5.08 oz)


Propeller Shaft Assembly:
Propeller shaft with center bearing assembly runout Front side Maximum runout: 0.4 mm (0.0157 in.)
Rear side Maximum runout: 0.4 mm (0.0157 in.)
Joint angle No. 1 Joint Angle -1°56' +/- 1°
No. 2 Joint Angle 1°00' +/- 1°
No. 3 Joint Angle 2°50' +/- 1°