Home › General › MAINTENANCE › REAR DISC BRAKE PAD (for 2-Pot Caliper) › from 2020.09
RM36W0E _V1 General _088300 MAINTENANCE _0448437 REAR DISC BRAKE PAD(for 2-Pot Caliper) A

MAINTENANCE  REAR DISC BRAKE PAD(for 2-Pot Caliper)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 04946 1.INSTALL REAR DISC BRAKE ANTI SQUEAL SHIM KIT

a.
C447966C01
0.573,1.063 0.573,0.792 false 1.313,1.344 1.313,1.073 false 2.104,1.604 2.104,1.333 false 2.792,1.854 2.792,1.583 false 0.479,1.063 0.792,1.219 0.313,0.156 10 false *1 1.24,1.365 1.552,1.521 0.313,0.156 10 false *2 2.031,1.615 2.344,1.771 0.313,0.156 10 false *3 2.729,1.875 3.042,2.031 0.313,0.156 10 false *1
*1 Rear Disc Brake Anti-squeal Shim
*2 Rear Disc Brake Pad (Inner)
*3 Rear Disc Brake Pad (Outer)


Install the 2 rear disc brake anti-squeal shims to each rear disc brake pad.

NOTICE:

When replacing the rear disc brake pads with new ones, make sure to replace the rear disc brake anti-squeal shim kit at the same time.



Hide 04466 2.INSTALL REAR DISC BRAKE PAD

a.
C447964N01
1.99,1.063 2.375,1.906 true 2.281,1.927 2.625,2.094 0.344,0.167 10 false SST

Using SST, push in the rear disc brake piston.

SST
09719-77010  

NOTICE:
·

Make sure the brake fluid does not overflow from the reservoir.

·

Do not forcibly push in the rear disc brake piston.




b.
C447965

Install the 2 rear disc brake pads to the rear disc brake cylinder assembly.

NOTICE:

The rear disc brake pad with the pad wear indicator plate must be installed to the inner lower side position.



Hide 47848 3.TEMPORARILY INSTALL REAR DISC BRAKE ANTI-RATTLE SPRING

a.
C447962C01
0.375,1.542 0.375,1.167 true 0.323,1.573 0.635,1.729 0.313,0.156 10 false *a
*a Arrow Mark


Temporarily install the rear disc brake anti-rattle spring to the rear disc brake pads.

NOTICE:
·

Install the rear disc brake anti-rattle spring so that its arrow mark is pointing upward.

·

The arrow mark of the rear disc brake anti-rattle spring is stamped on the outer side of the vehicle for the LH side, and the inner side of the vehicle for the RH side.




Hide 47748E 4.INSTALL REAR DISC BRAKE ANTI-RATTLE PIN

a.
C447959

Install the rear disc brake anti-rattle pin (upper side) and set the rear disc brake anti-rattle spring to the rear disc brake pads.

NOTICE:

Set the rear disc brake anti-rattle spring so that it does not overlap and ride up onto the rear disc brake cylinder assembly.



b.
C447960

While pressing the rear disc brake anti-rattle spring, install the rear disc brake anti-rattle pin (lower side).


Hide 47843 5.INSTALL REAR DISC BRAKE PIN HOLD CLIP

a.

Install the rear disc brake pin hold clip to the 2 rear disc brake anti-rattle pins and engage the hook to the rear disc brake cylinder assembly.


Hide 6.INSPECT BRAKE FLUID LEVEL IN RESERVOIR

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID (for Gasoline Model)>ON-VEHICLE INSPECTION

NOTICE:

After replacing the rear disc brake pads, the clearance between the rear disc brake pads and the rear disc will be large, so depress the brake pedal several times to adjust the clearance before inspecting the brake fluid level.


Hide 7.INSTALL REAR WHEEL