Home › Brake › BRAKE (REAR) › REAR BRAKE (for 2-Pot Caliper) › from 2020.09
RM36W0E _54 Brake _089429 BRAKE (REAR) _0448438 REAR BRAKE(for 2-Pot Caliper) A

BRAKE (REAR)  REAR BRAKE(for 2-Pot Caliper)  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:
·
C444645N01
2.24,0.344 2.385,0.51 0.146,0.167 10 true A 2.479,1.542 2.625,1.708 0.146,0.167 10 true B

To avoid degrading the precision of the assembly, do not loosen or remove the 2 bolts shown in the illustration.

·

If the bolts have been loosened or removed, use the following procedure to reassemble the parts.

(a)

Temporarily install the rear disc brake cylinder assembly with the 2 bolts.

(b)

Start the engine.

(c)

Depress the brake pedal to continuously apply hydraulic pressure.

(d)

Temporarily tighten bolt A to 30 N*m (306 kgf*cm, 22 ft.*lbf).

(e)

Temporarily tighten bolt B to 30 N*m (306 kgf*cm, 22 ft.*lbf).

(f)

Fully tighten bolt A to 70 N*m (714 kgf*cm, 52 ft.*lbf).

(g)

Fully tighten bolt B to 70 N*m (714 kgf*cm, 52 ft.*lbf).

(h)

Release the brake pedal to release the hydraulic pressure.

(i)

Check that the 2 bolts are tightened to 70 N*m (714 kgf*cm, 52 ft.*lbf).




HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.REMOVE REAR WHEEL

Hide 2.DRAIN BRAKE FLUID

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.


Hide 47843 3.REMOVE REAR DISC BRAKE PIN HOLD CLIP

Hide 47748E 4.REMOVE REAR DISC BRAKE ANTI-RATTLE PIN

Hide 47848 5.REMOVE REAR DISC BRAKE ANTI-RATTLE SPRING

Hide 04466 6.REMOVE REAR DISC BRAKE PAD

Hide 04946 7.REMOVE REAR DISC BRAKE ANTI SQUEAL SHIM KIT

Hide 47319F 8.DISCONNECT REAR LH FLEXIBLE HOSE

a.
C447967

Remove the union bolt and gasket, and disconnect the rear flexible hose from the rear disc brake cylinder assembly.


Hide 47850 9.REMOVE REAR DISC BRAKE CYLINDER ASSEMBLY

a.
C447968

Remove the 2 bolts and rear disc brake cylinder assembly from the rear axle carrier sub-assembly.


Hide 42491 10.REMOVE PARKING BRAKE SHOE ADJUSTING HOLE PLUG

a.
C447969

Remove the parking brake shoe adjusting hole plug from the rear disc.


Hide 42432 11.REMOVE REAR DISC

a.
C447970C01
1.896,1.135 2.833,1.479 2.833,1.479 1.844,1.021 true 2.865,1.406 3.177,1.604 0.313,0.198 10 false *a
*a Matchmark


Put matchmarks on the rear disc and the rear axle hub and bearing assembly.

HINT:

Not required when replacing the rear disc.



b.
C447971C01
0,0 0,0 false
V113147

Contract


Release the parking brake and remove the rear disc from the rear disc and the rear axle hub and bearing assembly.

HINT:

If the rear disc cannot be removed easily, use a screwdriver to turn the shoe adjuster as shown in the illustration in order to contract the parking brake shoes.