Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for Gasoline Model) › 2020.09–2021.04
RM36W0E _57 Power Source / Network _088060 NETWORKING _0424331 CAN COMMUNICATION SYSTEM(for Gasoline Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for Gasoline Model)  Radio Receiver Assembly Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Radio Receiver Assembly Communication Stop Mode Communication stop for "Display and Navigation (AVN1)" is indicated on the "Communication Bus Check" screen of the GTS.
Click here(Click here)
·

Radio and display receiver assembly branch line or connector

·

Power source circuit of radio and display receiver assembly

·

Radio and display receiver assembly ground circuit

·

Radio and display receiver assembly



WIRING DIAGRAM

C366187E09
1.635,0.531 1.813,0.719 0.177,0.188 10 false 3 1.635,1.063 1.875,1.25 0.24,0.188 10 false 14 0.083,1.573 1.5,1.875 1.417,0.302 10 false H115*3, H146*4 0.073,1.74 2.917,1.938 2.844,0.198 10 false No. 4 Global CAN Junction Connector 2.156,2.208 3.792,2.49 1.635,0.281 10 false from IGR-NO. 2 Relay 2.396,2.74 3.885,3 1.49,0.26 10 false from ACC Relay*1 2.031,3.698 3.521,3.927 1.49,0.229 10 false from Auxiliary Battery*1 4.177,2.375 5.302,2.583 1.125,0.208 10 false ECU-IGR NO. 2 4.313,2.896 4.969,3.115 0.656,0.219 10 false ECU-ACC 4.438,3.865 5.073,4.073 0.635,0.208 10 false RADIO 5.469,0.427 5.708,0.615 0.24,0.188 10 false 13 5.406,0.625 5.844,0.802 0.438,0.177 10 false H80 5.458,0.969 5.698,1.156 0.24,0.188 10 false 14 5.479,2.031 5.719,2.219 0.24,0.188 10 false 19 5.479,2.563 5.719,2.75 0.24,0.188 10 false 15 5.521,3.531 5.76,3.719 0.24,0.188 10 false 4 5.5,4.323 5.74,4.51 0.24,0.188 10 false 1 5.781,0.604 6.292,0.823 0.51,0.219 10 false CANH 5.781,1.146 6.292,1.365 0.51,0.219 10 false CANL 5.792,2.208 6.302,2.427 0.51,0.219 10 false IG 5.792,2.76 6.302,2.979 0.51,0.219 10 false ACC1 5.792,3.708 6.302,3.927 0.51,0.219 10 false +B1 5.792,4.521 6.302,4.74 0.51,0.219 10 false GND1 5.385,4.958 7,5.188 1.615,0.229 10 false Radio Receiver Assembly 1.396,3.219 4.052,3.469 2.656,0.25 10 false from Engine Stop and Start ECU*2 1.396,4.156 4.052,4.406 2.656,0.25 10 false from Engine Stop and Start ECU*2 0.458,4.521 3.115,4.771 2.656,0.25 10 false *1: w/o Stop and Start System 0.469,4.823 3.125,5.073 2.656,0.25 10 false *2: w/ Stop and Start System 4.896,2.677 5.135,2.865 0.24,0.188 10 false *1 4.896,3.615 5.135,3.802 0.24,0.188 10 false *1 5.219,3 5.458,3.188 0.24,0.188 10 false *2 5.219,3.958 5.458,4.146 0.24,0.188 10 false *2 5.417,1.156 5.771,1.333 0.354,0.177 10 false H80 5.417,2.229 5.833,2.406 0.417,0.177 10 false H80 5.417,2.76 5.719,2.938 0.302,0.177 10 false H79 5.417,3.719 5.802,3.896 0.385,0.177 10 false H79 5.427,4.542 5.833,4.708 0.406,0.167 10 false H79 0.469,5.135 3.125,5.385 2.656,0.25 10 false *3: except G16E-GTS 0.469,5.448 3.125,5.698 2.656,0.25 10 false *4: for G16E-GTS

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (RADIO AND DISPLAY RECEIVER ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H80 radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H80-13 (CANH) - H80-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK VEHICLE TYPE

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY)

2.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
w/ Stop and Start System A
w/o Stop and Start System B



A

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

B

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H79-1 (GND1) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) auxiliary battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H80-19 (IG) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



Result:
Result
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H79-4 (+B1) - Body ground Ignition switch off 10.5 to 16 V
H79-15 (ACC1) - Body ground Ignition switch ACC 10.5 to 16 V
Ignition switch off Below 1 V



Result:
Result
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

GO TO STOP AND START SYSTEM (BACKUP BOOST CONVERTER CIRCUIT)

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Disconnect the H79 and H80 radio and display receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H79-1 (GND1) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



c.

Reconnect the cable to the negative (-) auxiliary battery terminal.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H80-19 (IG) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
H79-4 (+B1) - Body ground Ignition switch off 11 to 14 V
H79-15 (ACC1) - Body ground Ignition switch ACC 11 to 14 V
Ignition switch off Below 1 V



Result:
Result
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)