Home › Engine / Hybrid System › G16E-GTS (STARTING) › STARTER › from 2020.09
RM36W0E _51 Engine / Hybrid System _095693 G16E-GTS STARTING _0449410 STARTER A

G16E-GTS STARTING  STARTER  DISASSEMBLY  


PROCEDURE

Hide 1.REMOVE WIRE HARNESS

a.
A471558

Remove the 2 nuts and wire harness from the starter assembly.


Hide 28249 2.REMOVE STARTER INRUSH CURRENT REDUCTION RELAY

a.
A471559

Remove the bolt and wire harness from the starter inrush current reduction relay.


b.
A471560

Remove the 2 bolts and starter inrush current reduction relay from the starter drive housing assembly.


Hide 28226B 3.REMOVE REPAIR SERVICE STARTER KIT

a.
A399947

While holding the repair service starter kit to the starter drive housing assembly, remove the 2 nuts.


b.
A400186C05
1.417,0.083 1.583,0.313 true 0.333,0.333 0.75,0.531 true 1.25,0.01 1.563,0.167 0.313,0.156 10 false *a 0.125,0.25 0.438,0.406 0.313,0.156 10 false *1
*1 Pinion Drive Lever
*a Hook


While lifting the rear of the magnet starter switch assembly, remove the hook from the pinion drive lever, then remove the magnet starter switch assembly.


Hide 28120 4.REMOVE STARTER YOKE ASSEMBLY

a.
A474264C01
1,2 1.167,2 1.167,2 1.583,1.813 true 2.75,0.927 2.917,0.667 2.917,0.667 3.083,0.667 false 0.802,1.927 1.115,2.083 0.313,0.156 10 false *1 3.156,0.604 3.385,0.771 0.229,0.167 10 false *2
*1 Starter Yoke Assembly
*2 Starter Commutator End Frame Assembly


Using a T25 "TORX" socket wrench, remove the 2 through bolts, and pull out the starter yoke assembly together with the starter commutator end frame assembly.


Hide 5.REMOVE STARTER COMMUTATOR END FRAME ASSEMBLY

a.
A187214

Remove the 2 screws.


b.
A187221C16
0.646,1.125 0.76,1.125 0.76,1.125 0.969,0.938 false 1.563,1.458 1.667,1.458 1.667,1.458 1.885,1.271 false 1.49,0.156 1.906,0.156 false 0.438,1.052 0.635,1.281 0.198,0.229 10 false *1 1.333,1.385 1.573,1.625 0.24,0.24 10 false *2 1.979,0.073 2.219,0.313 0.24,0.24 10 false *a
*1 Starter Yoke Assembly
*2 Starter Commutator End Frame Assembly
*a Field Coil Lead Wire


While holding down the field coil lead wire, remove the starter commutator end frame assembly from the starter yoke assembly.


Hide 6.REMOVE STARTER BRUSH HOLDER ASSEMBLY

a.
A064784C23
1.073,0.208 1.313,0.208 1.313,0.208 1.552,0.51 false 1.948,0.563 2.167,0.219 2.167,0.219 2.396,0.219 false 2.458,0.094 2.771,0.25 0.313,0.156 10 false *a 0.885,0.104 1.198,0.26 0.313,0.156 10 false *b
*a Brush Spring
*b Brush


Using a screwdriver, hold the brush spring back and disconnect the 4 brushes.


b.

Remove the starter brush holder assembly from the starter armature assembly.


Hide 28160 7.REMOVE STARTER ARMATURE ASSEMBLY

a.
A202438C08
1.49,0.406 1.938,0.229 1.938,0.229 2.188,0.229 false 1.615,1.958 1.823,1.958 1.823,1.958 2.073,1.635 false 2.229,0.135 2.542,0.333 0.313,0.198 10 false *1 1.417,1.885 1.729,2.083 0.313,0.198 10 false *2
*1 Starter Yoke Assembly
*2 Starter Armature Assembly


Remove the starter armature assembly from the starter yoke assembly.


Hide 8.REMOVE STARTER ARMATURE PLATE

a.
A474265C01
0.396,0.625 0.729,0.625 false 2.417,1.958 2.417,1.625 true 1.25,1.875 1.583,1.875 false 3,1.854 3,1.521 false 2.938,1.875 3.25,2.031 0.313,0.156 10 false *1 0.25,0.542 0.563,0.698 0.313,0.156 10 false *2 1.646,1.813 1.958,1.969 0.313,0.156 10 false *3 2.354,1.99 2.667,2.146 0.313,0.156 10 false *3
*1 Starter Yoke Assembly
*2 Starter Drive Housing Assembly
*3 Starter Armature Plate


Remove the starter armature plate from the starter drive housing assembly or starter yoke assembly.


Hide 9.REMOVE PLANETARY GEAR

a.
A474266

Remove the 3 planetary gears from the starter drive housing assembly.


Hide 28021 10.REMOVE STARTER CENTER BEARING CLUTCH SUB-ASSEMBLY

a.
A474267C01
1.76,0.333 2.094,0.333 false 1.802,1.833 2.135,1.833 false 0.333,1.385 0.333,1.052 false 2.917,1.135 2.917,0.802 false 1.604,1.76 1.917,1.917 0.313,0.156 10 false *1 0.271,1.417 0.583,1.573 0.313,0.156 10 false *2 1.542,0.26 1.854,0.417 0.313,0.156 10 false *3 2.854,1.177 3.167,1.333 0.313,0.156 10 false *4
*1 Starter Center Bearing Clutch Sub-assembly
*2 Starter Drive Housing Assembly
*3 Pinion Drive Lever
*4 Rubber Seal


Remove the starter center bearing clutch sub-assembly together with the pinion drive lever and rubber seal from the starter drive housing assembly.


b.

Remove the pinion drive lever and rubber seal from the starter center bearing clutch sub-assembly.