Home › Engine / Hybrid System › G16E-GTS (STARTING) › STARTER › from 2020.09
RM36W0E _51 Engine / Hybrid System _095693 G16E-GTS STARTING _0449410 STARTER A

G16E-GTS STARTING  STARTER  REASSEMBLY  


PROCEDURE

Hide 28021 1.INSTALL STARTER CENTER BEARING CLUTCH SUB-ASSEMBLY

a.
A474271C01
0.333,1.083 0.333,1.417 false 1.823,1.917 2.156,1.917 false 1.771,0.292 2.104,0.292 false 2.917,0.813 2.917,1.146 false 1.615,1.854 1.927,2.01 0.313,0.156 10 false *1 0.271,1.427 0.583,1.583 0.313,0.156 10 false *2 1.542,0.229 1.854,0.385 0.313,0.156 10 false *3 2.854,1.167 3.167,1.323 0.313,0.156 10 false *4
*1 Starter Center Bearing Clutch Sub-assembly
*2 Starter Drive Housing Assembly
*3 Pinion Drive Lever
*4 Rubber Seal
V100135

High-temperature Grease


Apply high-temperature grease to the pinion drive lever as shown in the illustration.


b.

Install the pinion drive lever and rubber seal to the starter center bearing clutch sub-assembly.


c.

Install the starter center bearing clutch sub-assembly together with the pinion drive lever and rubber seal to the starter drive housing assembly.


Hide 2.INSTALL PLANETARY GEAR

a.
A474273C01
0,0 0,0 false
V100135

High-temperature Grease


Apply high-temperature grease to the 3 planetary gears, 3 planetary gear shafts and starter center bearing clutch sub-assembly.


b.

Install the 3 planetary gears to the starter center bearing clutch sub-assembly.


Hide 28160 3.INSTALL STARTER ARMATURE ASSEMBLY

a.
A347623

Install the starter armature assembly to the starter yoke assembly.

NOTICE:

The magnet of the starter yoke assembly may attract the starter armature assembly when the starter armature assembly is installed, causing the magnet to break.



Hide 28140 4.INSTALL STARTER BRUSH HOLDER ASSEMBLY

a.
A211303

Hold the brush spring back and set the 4 brushes as shown in the illustration.


b.
A211304

Install the starter brush holder assembly to the starter armature assembly and push in the 4 brushes as shown in the illustration.


c.
A314282C02
1.396,0.219 1.552,0.219 1.552,0.219 2.458,0.771 true 2.51,0.563 2.938,0.156 2.938,0.156 3.073,0.156 true 2.167,1.542 2.302,1.542 2.302,1.542 2.51,0.958 true 1.208,0.104 1.521,0.26 0.313,0.156 10 false *a 3.146,0.063 3.375,0.219 0.229,0.156 10 false *b 1.99,1.438 2.302,1.594 0.313,0.156 10 false *c
*a Grommet
*b Negative (-) Brush Holder Plate
*c Positive (+) Motor Lead Wire


Fit the protrusion of the grommet between the negative (-) brush holder plate and positive (+) motor lead wire.


Hide 28130 5.INSTALL STARTER COMMUTATOR END FRAME ASSEMBLY

a.
A209964C03
1.885,0.24 2.052,0.24 2.052,0.24 2.219,0.396 false 1.25,2.01 1.51,2.01 1.51,2.01 2.031,1.208 true 0.469,1.813 0.635,1.813 0.635,1.813 1.198,0.885 true 0.281,1.719 0.594,1.875 0.313,0.156 10 false *a 1.083,1.906 1.396,2.104 0.313,0.198 10 false *b 1.729,0.125 2.042,0.281 0.313,0.156 10 false *a
*a Field Coil Lead Wire Rubber
*b Cutout


Install the starter commutator end frame assembly to the starter yoke assembly.

NOTICE:

Align the field coil lead wire rubber of the starter yoke assembly with the cutout of the starter commutator end frame assembly.



b.
A187214

Install the 2 screws.

Torque:
1.5 N*m (15 kgf*cm, 13 in.*lbf)


Hide 6.INSTALL STARTER ARMATURE PLATE

a.
A204351C21
3.021,1.448 2.865,1.448 2.865,1.448 2.531,1.885 true 1.552,1.531 1.552,1.875 true 2.458,0.865 2.271,0.865 2.271,0.865 1.865,1.313 true 1.906,0.26 1.719,0.26 1.719,0.26 1.448,0.625 false 3.104,0.792 2.948,0.792 2.948,0.792 2.615,1.229 false 3.167,0.708 3.427,0.948 0.26,0.24 10 false *2 2.521,0.792 2.802,1.01 0.281,0.219 10 false *a 2,0.198 2.313,0.396 0.313,0.198 10 false *1 3.063,1.365 3.375,1.563 0.313,0.198 10 false *b 1.5,1.906 1.781,2.125 0.281,0.219 10 false *a
*1 Starter Yoke Assembly
*2 Starter Armature Plate
*a Protrusion
*b Stopper


Align the starter armature plate so that the protrusion fits between the stoppers of the starter yoke assembly, and install the starter armature plate.

NOTICE:

Make sure the protrusion of the starter armature plate is inserted between the stoppers of the starter yoke assembly.



Hide 28120 7.INSTALL STARTER YOKE ASSEMBLY

a.
A478830C01
2.677,1.854 2.677,1.365 true 1.792,0.281 2.125,0.281 false 0.75,0.5 0.917,0.5 0.917,0.5 1.198,0.938 false 1.719,1.813 1.719,1.479 false 0.563,0.427 0.875,0.583 0.313,0.156 10 false *1 1.604,0.198 1.917,0.354 0.313,0.156 10 false *2 2.625,1.885 2.938,2.042 0.313,0.156 10 false *a 1.646,1.875 1.958,2.031 0.313,0.156 10 false *b
*1 Starter Yoke Assembly
*2 Starter Drive Housing Assembly
*a Cutout
*b Protrusion


Align the protrusion of the starter yoke assembly with the cutout of the starter drive housing assembly.


b.
A474264C01
1,2 1.167,2 1.167,2 1.583,1.813 true 2.75,0.927 2.917,0.667 2.917,0.667 3.083,0.667 false 0.802,1.927 1.115,2.083 0.313,0.156 10 false *1 3.156,0.604 3.385,0.771 0.229,0.167 10 false *2
*1 Starter Yoke Assembly
*2 Starter Commutator End Frame Assembly


Using a T25 "TORX" socket wrench, install the 2 through bolts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 28150 8.INSTALL MAGNET STARTER SWITCH ASSEMBLY

a.
A434944C02
0.823,0.635 0.396,0.344 0.396,0.344 0.219,0.344 true 1.625,0.385 1.521,0.115 1.521,0.115 1.292,0.115 true 1.125,0.052 1.448,0.302 0.323,0.25 10 false *a 0.052,0.281 0.427,0.563 0.375,0.281 10 false *1
*1 Pinion Drive Lever
*a Hook
V100135

High-temperature Grease


Apply high-temperature grease to the magnet starter switch assembly as shown in the illustration.


b.

Hang the hook of the magnet starter switch assembly on the pinion drive lever.


c.
A399947

Install the magnet starter switch assembly with the 2 nuts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 28249 9.INSTALL STARTER INRUSH CURRENT REDUCTION RELAY

A471560

a.

Install the starter inrush current reduction relay to the starter drive housing assembly with the 2 bolts.

Torque:
7.9 N*m (81 kgf*cm, 70 in.*lbf)


b.
A471559

Connect the field coil lead wire to the starter inrush current reduction relay with the nut.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


Hide 10.INSTALL WIRE HARNESS

a.
A471558

Install the wire harness to the starter assembly with the 2 nuts.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)