Home › Vehicle Interior › HEATING / AIR CONDITIONING › FRONT EVAPORATOR TEMPERATURE SENSOR › from 2020.09
RM36W0E _58 Vehicle Interior _088019 HEATING / AIR CONDITIONING _0424506 FRONT EVAPORATOR TEMPERATURE SENSOR A

HEATING / AIR CONDITIONING  FRONT EVAPORATOR TEMPERATURE SENSOR  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RHD and LHD vehicles.

·

The procedure listed below is for the LHD vehicles.



PROCEDURE

Hide 88625 1.INSTALL NO. 1 COOLER THERMISTOR

a.

for Type A:

i.
I117146C01
1.823,3.219 2.01,2.979 true 2.469,3.198 2.177,2.979 true 1.542,1.073 1.344,0.813 false 2.135,1.052 2.396,0.677 true 0.448,2.885 0.74,3.135 0.292,0.25 10 false A 0.979,3.063 1.271,3.313 0.292,0.25 10 false B 1.917,0.51 2.208,0.76 0.292,0.25 10 false X 2.49,3.156 2.729,3.365 0.24,0.208 10 true *a 1.625,3.167 1.813,3.396 0.188,0.229 10 true *b 1.01,3.719 1.302,3.969 0.292,0.25 10 false C 1.573,4.052 1.865,4.302 0.292,0.25 10 false D 2.458,0.563 2.615,0.76 0.156,0.198 10 false a 1.229,0.719 1.385,0.917 0.156,0.198 10 false b
*a Fixed Part
*b Sensor Part


Install the No. 1 cooler thermistor as shown in the illustration.

Installation Position:
Part Length
A 45 to 55 mm (1.77 to 2.17 in.)
B 23 to 27 mm (0.906 to 1.06 in.)
C 54.4 mm (2.14 in.)
D 61.1 mm (2.41 in.)


NOTICE:
·

Be sure to insert the No. 1 cooler thermistor only once because reinserting it into the same position will not allow it to be firmly secured.

·

When reusing the No. 1 cooler evaporator sub-assembly, insert the No. 1 cooler thermistor one row next to the one that has been used previously (X in the illustration).

·

After inserting the No. 1 cooler thermistor, do not apply excessive force to the wire.

·

Directly insert the No. 1 cooler thermistor until the edge of the plastic case "a" comes into contact with the No. 1 cooler evaporator sub-assembly "b".





b.

for Type B:

i.
E400531C04
1.604,3.188 1.927,2.74 true 2.573,3.146 2.188,2.75 true 2.292,1 2.552,0.615 false 1.719,0.969 1.344,0.542 true 0.323,3.083 0.615,3.333 0.292,0.25 10 false A 1.594,4.344 1.885,4.594 0.292,0.25 10 false B 1.854,0.375 2.146,0.625 0.292,0.25 10 false X 1.406,3.156 1.646,3.365 0.24,0.208 10 true *a 2.521,3.167 2.708,3.396 0.188,0.229 10 true *b 1.208,0.438 1.365,0.635 0.156,0.198 10 false a 2.594,0.531 2.75,0.729 0.156,0.198 10 false b
*a Fixed Part
*b Sensor Part


Install the No. 1 cooler thermistor as shown in the illustration.

Installation Position:
Part Length
A 45 to 55 mm (1.77 to 2.17 in.)
B 61.1 mm (2.41 in.)


NOTICE:
·

Be sure to insert the No. 1 cooler thermistor only once because reinserting it into the same position will not allow it to be firmly secured.

·

When reusing the No. 1 cooler evaporator sub-assembly, insert the No. 1 cooler thermistor one row next to the one that has been used previously (X in the illustration).

·

After inserting the No. 1 cooler thermistor, do not apply excessive force to the wire.

·

Directly insert the No. 1 cooler thermistor until the edge of the plastic case "a" comes into contact with the No. 1 cooler evaporator sub-assembly "b".





Hide 88501 2.INSTALL NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY

Hide 87107A 3.INSTALL HEATER RADIATOR UNIT SUB-ASSEMBLY