Home › Drivetrain › EA67F (MANUAL TRANSMISSION / TRANSAXLE) › INPUT SHAFT › from 2020.09
RM36W0E _52 Drivetrain _095283 EA67F MANUAL TRANSMISSION / TRANSAXLE _0449606 INPUT SHAFT A

EA67F MANUAL TRANSMISSION / TRANSAXLE  INPUT SHAFT  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL INPUT SHAFT FRONT BEARING INNER RACE

a.
C112447N01
0.551,1.214 0.876,1.404 0.326,0.19 10 SST 0.897,1.296 1.04,1.296 1.04,1.296 1.533,1.667 false

Using SST and a press, install the input shaft front bearing inner race to the input shaft.

SST
09608-00071  


Hide 33311T 2.INSTALL INPUT SHAFT SNAP RING

a.
C112448

Using a brass bar and hammer, tap a new input shaft snap ring to the input shaft.


Hide 33334 3.INSTALL 4TH DRIVE GEAR

a.
C112449N01
2.296,1.047 2.602,1.211 0.306,0.164 10 SST 2.501,0.846 2.438,0.846 2.438,0.846 2.438,1.03 false

Using SST and a press, install the 4th drive gear to the input shaft.

SST
09309-14040  


Hide 33333 4.INSTALL 3RD DRIVE GEAR

a.
C112450

Install the spacer to the input shaft.


b.
C112451N01
0.539,1.412 0.844,1.579 0.306,0.167 10 SST 0.887,1.498 1.003,1.498 1.003,1.498 1.624,1.953 false

Using SST and a press, install the 3rd drive gear to the input shaft.

SST
09309-14040  


Hide 33337 5.INSTALL 6TH DRIVE GEAR

a.
C112452N01
2.521,0.896 2.417,0.896 2.417,0.896 2.417,1.073 false 2.302,1.135 2.604,1.313 0.302,0.177 10 SST

Using SST and a press, install the 6th drive gear to the input shaft.

SST
09309-14040  


Hide 33311E 6.INSTALL INPUT SHAFT REAR RADIAL BALL BEARING

a.
C112454N01
2.406,1.177 2.406,1.021 2.406,1.021 2.5,1.021 false 2.313,1.188 2.615,1.344 0.302,0.156 10 SST

Using SST and a press, install the input shaft rear radial ball bearing to the input shaft.

SST
09506-30012  


Hide 33311P 7.INSTALL INPUT SHAFT REAR BEARING SHAFT SNAP RING

a.
C118745C01
3.063,0.927 2.844,1.49 false 2.771,1.531 3.229,1.885 0.458,0.354 10 *a
*a Mark


Select a new input shaft rear bearing shaft snap ring, using the table below, that makes the thrust clearance of the input shaft bearing less than 0.1 mm (0.00394 in.).

Input Shaft Rear Bearing Shaft Snap Ring Thickness:
Mark Thickness mm (in.) Mark Thickness mm (in.)
A 1.80 to 1.85 (0.0709 to 0.0728) 3 2.20 to 2.25 (0.0866 to 0.0886)
B 1.85 to 1.90 (0.0728 to 0.0748) 4 2.25 to 2.30 (0.0886 to 0.0906)
C 1.90 to 1.95 (0.0748 to 0.0768) 5 2.30 to 2.35 (0.0906 to 0.0925)
D 1.95 to 2.00 (0.0768 to 0.0787) 6 2.35 to 2.40 (0.0925 to 0.0945)
E 2.00 to 2.05 (0.0787 to 0.0807) F 2.40 to 2.45 (0.0945 to 0.0965)
0 2.05 to 2.10 (0.0807 to 0.0827) G 2.45 to 2.50 (0.0965 to 0.0984)
1 2.10 to 2.15 (0.0827 to 0.0846) H 2.50 to 2.55 (0.0984 to 0.1004)
2 2.15 to 2.20 (0.0846 to 0.0866) - -


b.
C112390

Using a snap ring expander, install the input shaft rear bearing shaft snap ring to the input shaft.