1.INSPECT 1ST DRIVEN GEAR THRUST CLEARANCE
2.INSPECT 1ST DRIVEN GEAR RADIAL CLEARANCE
3.INSPECT 2ND DRIVEN GEAR THRUST CLEARANCE
4.INSPECT 2ND DRIVEN GEAR RADIAL CLEARANCE
5.INSPECT 3RD DRIVEN GEAR THRUST CLEARANCE
6.INSPECT 3RD DRIVEN GEAR RADIAL CLEARANCE
7.INSPECT 4TH DRIVEN GEAR THRUST CLEARANCE
8.INSPECT 4TH DRIVEN GEAR RADIAL CLEARANCE
33321C
9.REMOVE OUTPUT SHAFT BEARING SHAFT SNAP RING
Using a snap ring expander, remove the output shaft bearing shaft snap ring from the No. 1 output shaft.
33321A
10.REMOVE OUTPUT SHAFT REAR BEARING
Using SST and a press, remove the output shaft rear bearing from the No. 1 output shaft.
11.REMOVE SPACER
Remove the spacer from the No. 1 output shaft.
33333A
12.REMOVE 3RD GEAR NEEDLE ROLLER BEARING
Remove the needle roller bearing from the No. 1 output shaft.
33047
13.REMOVE 3RD DRIVEN GEAR SYNCHRONIZER RING SET
Remove the 3rd driven gear synchronizer ring set from the No. 1 output shaft.
33352C
14.REMOVE SHAFT SNAP RING
Using 2 screwdrivers and a hammer, remove the shaft snap ring from the No. 1 output shaft.
33422B
15.REMOVE 4TH DRIVEN GEAR
Using SST and a press, remove the No. 2 transmission hub sleeve, 4th driven gear synchronizer ring set, and 4th driven gear from the No. 1 output shaft.
33047
16.REMOVE 4TH DRIVEN GEAR SYNCHRONIZER RING SET
Remove the 4th driven gear synchronizer ring set from the 4th driven gear.
33362
17.REMOVE NO. 2 TRANSMISSION CLUTCH HUB
Remove the No. 2 transmission clutch hub, 3 No. 1 synchromesh shifting keys, 3 balls and 3 synchronizer shifting key springs from the No. 2 transmission hub sleeve.
Pay attention to prevent the balls and synchronizer shifting key springs from scattering.
33334B
18.REMOVE 4TH GEAR BEARING SPACER
Remove the needle roller bearing from the No. 1 output shaft.
33334B
19.REMOVE SPACER
Remove the spacer from the No. 1 output shaft.
33321C
20.REMOVE OUTPUT SHAFT BEARING SHAFT SNAP RING
Using a snap ring expander, remove the output shaft bearing shaft snap ring from the No. 1 output shaft.
33356A
21.REMOVE 2ND GEAR BEARING INNER RACE
Remove the 2nd driven gear bearing inner race from the No. 1 output shaft.
33332
22.REMOVE 2ND DRIVEN GEAR
Remove the 2nd driven gear from the No. 1 output shaft.
33332B
23.REMOVE NEEDLE ROLLER BEARING
Remove the needle roller bearing from the No. 1 output shaft.
33365C
24.REMOVE SYNCHROMESH SHIFTING KEY BALL
| *a | Magnet Hand |
Using a magnet hand, remove the synchromesh shifting key ball from the No. 1 output shaft.
33037B
25.REMOVE NO. 1 SYNCHRONIZER RING SET
Remove the 2nd driven gear synchronizer ring set from the No. 1 output shaft.
33335
26.REMOVE 1ST DRIVEN GEAR
Using SST and a press, remove the No. 1 transmission hub sleeve, 1st driven gear synchronizer ring set and 1st driven gear from the No. 1 output shaft.
33037B
27.REMOVE 1ST DRIVEN GEAR SYNCHRONIZER RING SET
Remove the 1st driven synchronizer ring set from the 1st driven gear.
33361
28.REMOVE NO. 1 TRANSMISSION CLUTCH HUB
Remove the No. 1 transmission clutch hub, 3 No. 1 synchromesh shifting keys, 3 balls and 3 synchronizer shifting key springs from the No. 1 transmission hub sleeve.
Pay attention to prevent the balls and synchronizer shifting key springs from scattering.
33335C
29.REMOVE NEEDLE ROLLER BEARING
Remove the needle roller bearing from the No. 1 output shaft.
33321N
30.REMOVE OUTPUT SHAFT FRONT BEARING INNER RACE
Using SST and a press, remove the output shaft front bearing inner race from the No. 1 output shaft.
31.INSPECT 5TH DRIVEN GEAR THRUST CLEARANCE
32.INSPECT 5TH DRIVEN GEAR RADIAL CLEARANCE
33.INSPECT 6TH DRIVEN GEAR THRUST CLEARANCE
34.INSPECT 6TH DRIVEN GEAR RADIAL CLEARANCE
35.INSPECT REVERSE DRIVEN GEAR THRUST CLEARANCE
36.INSPECT REVERSE DRIVEN GEAR RADIAL CLEARANCE
33322C
37.REMOVE NO. 2 OUTPUT SHAFT BEARING SNAP RING
Using a snap ring expander, remove the No. 2 output shaft bearing snap ring from the No. 2 output shaft.
33322A
38.REMOVE NO. 2 OUTPUT SHAFT REAR BEARING
Using SST and a press, remove the No. 2 output shaft rear bearing and 6th driven gear from the No. 2 output shaft.
33337A
39.REMOVE NEEDLE ROLLER BEARING
Remove the needle roller bearing from the No. 2 output shaft.
40.REMOVE SPACER
Remove the spacer from the No. 2 output shaft.
33369B
41.REMOVE 6TH DRIVEN GEAR SYNCHRONIZER RING
Remove the 6th driven gear synchronizer ring from the No. 2 output shaft.
33352C
42.REMOVE SHAFT SNAP RING
Using 2 screwdrivers and a hammer, remove the shaft snap ring from the No. 2 output shaft.
33428C
43.REMOVE 5TH DRIVEN GEAR
Using SST and a press, remove the No. 3 transmission hub sleeve, 5th driving gear synchronizer ring, 5th driven gear, 2 spacers and needle roller bearing from the No. 2 output shaft.
33368J
44.REMOVE 5TH DRIVEN GEAR SYNCHRONIZER RING
Remove the 5th driven gear synchronizer ring from the 5th driven gear.
33393
45.REMOVE NO. 3 TRANSMISSION CLUTCH HUB
Remove the No. 3 transmission clutch hub, 3 No. 1 synchromesh shifting keys, 3 ball and 3 synchronizer shifting key springs from the No. 3 transmission hub sleeve.
Pay attention to prevent the balls and synchronizer shifting key springs from scattering.
33352C
46.REMOVE SHAFT SNAP RING
Using 2 screwdrivers and a hammer, remove the shaft snap ring from the No. 2 output shaft.
33331
47.REMOVE REVERSE DRIVEN GEAR
Using SST and a press, remove the No. 4 transmission hub sleeve, reverse driven gear synchronizer ring and reverse driven gear from the No. 2 output shaft.
48.REMOVE REVERSE DRIVEN GEAR SYNCHRONIZER RING
Remove the reverse driven gear synchronizer ring from the reverse driven gear.
33352B
49.REMOVE NO. 4 TRANSMISSION CLUTCH HUB
| *1 | Hub Sleeve |
| *2 | Shifting Key |
| *3 | Key Spring |
| *4 | No. 4 Transmission Clutch Hub |
Remove the No. 4 transmission clutch hub, key spring and shifting key from the No. 4 transmission hub sleeve.
33333A
50.REMOVE NEEDLE ROLLER BEARING
Remove the needle roller bearing from the No. 2 output shaft.
33322B
51.REMOVE NO. 2 OUTPUT SHAFT FRONT BEARING
Using SST and a press, remove the No. 2 output shaft front bearing from the No. 2 output shaft.