Home › Drivetrain › EA67F (MANUAL TRANSMISSION / TRANSAXLE) › OUTPUT SHAFT › from 2020.09
RM36W0E _52 Drivetrain _095283 EA67F MANUAL TRANSMISSION / TRANSAXLE _0449607 OUTPUT SHAFT A

EA67F MANUAL TRANSMISSION / TRANSAXLE  OUTPUT SHAFT  REASSEMBLY  


PROCEDURE

Hide 33331A 1.INSTALL NEEDLE ROLLER BEARING

a.
C112406

Coat the needle roller bearing with gear oil and install it to the No. 2 output shaft.


Hide 33331 2.INSTALL REVERSE DRIVEN GEAR

a.
C275844

Coat the reverse driven gear with gear oil and install it to the No. 2 output shaft.


Hide 33352B 3.INSTALL NO. 4 TRANSMISSION CLUTCH HUB

a.
C116552C01
0.833,0.531 0.833,0.188 0.833,0.188 1,0.188 false 1.844,0.917 1.844,0.469 1.844,0.469 2.073,0.469 false 2.125,1.667 2.125,2 false 2.552,1.875 2.552,2.281 false 2.167,3.469 1.76,3.469 false 0.677,3.177 1.5,3.448 false 1.188,1.438 0.938,1.552 false 2.51,2.323 3.24,2.688 0.729,0.365 10 *5 2.073,2.052 2.802,2.385 0.729,0.333 10 *4 2.135,0.385 2.938,0.792 0.802,0.406 10 *2 1.052,0.115 1.813,0.521 0.76,0.406 10 *1 0.75,1.542 1.948,2.167 1.198,0.625 10 *3 1.563,3.385 1.906,3.781 0.344,0.396 10 *a
*1 No. 4 Transmission Hub Sleeve
*2 Shifting Key
*3 Reverse Driven Gear Synchronizer Ring
*4 Key Spring
*5 No. 4 Transmission Clutch Hub
*a Claw


Install the reverse driven gear synchronizer ring, key spring and shifting key to the No. 4 transmission clutch hub.

HINT:
·

Install the shifting key with the grooves on the No. 4 transmission clutch hub side.

·

Install the key spring with the claw on the No. 4 transmission clutch hub side.

·

Refer to the illustration when installing the key spring and shifting key.




b.

Install the No. 4 transmission hub sleeve to the reverse driven gear as shown in the illustration.


c.
C116199N01
0.259,1.001 0.6,1.34 0.34,0.34 10 SST 0.659,1.081 0.805,1.081 0.805,1.081 1.13,1.313 false

Coat the No. 4 transmission clutch hub with gear oil and install it to the No. 2 output shaft.


d.

Using SST and a press, install the reverse driven gear and No. 4 transmission clutch hub to the No. 2 output shaft.

SST
09308-14010  

NOTICE:

After installation, make sure that the gear and synchronizer ring move smoothly.


HINT:

Make sure that the protruding part on the reverse driven gear synchronizer ring is fitted into the groove of the No. 4 transmission clutch hub.



Hide 33352C 4.INSTALL SHAFT SNAP RING

a.
C275845C01
2.51,0.875 1.833,0.344 1.833,0.344 1.427,0.344 false 1.219,0.25 1.531,0.448 0.313,0.198 10 *a
*a Mark


Select a new shaft snap ring, using the table below, that makes the thrust clearance of the No. 4 transmission clutch hub less than 0.1 mm (0.00394 in.).

Shaft Snap Ring Thickness:
Mark Thickness mm (in.) Mark Thickness mm (in.)
A 2.25 to 2.30 (0.0886 to 0.0906) E 2.45 to 2.50 (0.0965 to 0.0984)
B 2.30 to 2.35 (0.0906 to 0.0925) F 2.50 to 2.55 (0.0984 to 0.1004)
C 2.35 to 2.40 (0.0925 to 0.0945) G 2.55 to 2.60 (0.1004 to 0.1024)
D 2.40 to 2.45 (0.0945 to 0.0965) H 2.60 to 2.65 (0.1024 to 0.1043)


b.
C112456

Using a brass bar and hammer, tap the shaft snap ring to the No. 2 output shaft.


Hide 5.INSPECT REVERSE DRIVEN GEAR THRUST CLEARANCE

Hide 6.INSPECT REVERSE DRIVEN GEAR RADIAL CLEARANCE

Hide 33428C 7.INSTALL 5TH DRIVEN GEAR

a.
C112402

Install the spacer to the No. 2 output shaft.


b.
C112401

Coat the needle roller bearing with gear oil and install it to the No. 2 output shaft.


c.
C112400

Install the spacer to the No. 2 output shaft.


d.
C116206

Coat the 5th driven gear with gear oil and install it to the No. 2 output shaft.


Hide 33393 8.INSTALL NO. 3 TRANSMISSION CLUTCH HUB

a.
C116553

Apply gear oil to the No. 3 transmission hub sleeve and No. 3 transmission clutch hub.


b.

Install the No. 3 transmission hub sleeve to the No. 3 transmission clutch hub.


c.

Install the 3 No. 1 synchromesh shifting keys to the No. 3 transmission clutch hub.


d.

Install the 3 synchronizer shifting key springs to the No. 3 transmission clutch hub.


e.

Place the balls in the holes of the No. 1 synchromesh shifting keys and install the No. 3 transmission hub sleeve while pushing in the balls.

NOTICE:

Take care to prevent the balls from scattering.



f.

Coat the 5th driven gear synchronizer ring with gear oil and install it to the 5th driven gear.


g.
C116200N01
0.645,0.215 1.01,0.55 0.366,0.336 10 SST 1.016,0.312 1.218,0.312 1.218,0.312 1.512,0.652 false

Using SST and a press, install the No. 3 transmission clutch hub to the No. 2 output shaft.

SST
09308-14010  

NOTICE:

After installation, make sure that the gear and synchronizer ring move smoothly.


HINT:

Make sure that the protruding part on the 5th driven gear synchronizer ring is fitted into the groove of the No. 3 transmission clutch hub.



Hide 33352C 9.INSTALL SHAFT SNAP RING

a.
C275846C02
0.958,1.667 0.958,0.531 false 0.885,1.708 1.198,1.906 0.313,0.198 10 *a
*a Mark


Select a new shaft snap ring, using the table below, that makes the thrust clearance of the No. 3 transmission clutch hub less than 0.1 mm (0.00394 in.).

Shaft Snap Ring Thickness:
Mark Thickness mm (in.) Mark Thickness mm (in.)
1 2.25 to 2.30 (0.0886 to 0.0906) 4 2.40 to 2.45 (0.0945 to 0.0965)
2 2.30 to 2.35 (0.0906 to 0.0925) 5 2.45 to 2.50 (0.0965 to 0.0984)
3 2.35 to 2.40 (0.0925 to 0.0945) 6 2.50 to 2.55 (0.0984 to 0.1004)


b.
C112462

Using a brass bar and hammer, tap the shaft snap ring to the No. 2 output shaft.


Hide 10.INSPECT 5TH DRIVEN GEAR THRUST CLEARANCE

Hide 11.INSPECT 5TH DRIVEN GEAR RADIAL CLEARANCE

Hide 33429B 12.INSTALL 6TH DRIVEN GEAR

a.
C116203

Install the spacer to the No. 2 output shaft.


b.
C116204

Coat the needle roller bearing with gear oil and install it to the No. 2 output shaft.


c.
C116202

Coat the 6th driven gear synchronizer ring with gear oil and install it to the No. 3 transmission clutch hub.


d.
C116555

Coat the 6th driven gear with gear oil and install it to the No. 2 output shaft.


Hide 33322A 13.INSTALL NO. 2 OUTPUT SHAFT REAR BEARING

a.
C112458N01
0.159,0.263 0.469,0.586 0.31,0.323 10 SST 0.547,0.352 0.813,0.352 0.813,0.352 1.027,0.546 false

Using SST and a press, install the No. 2 output shaft rear bearing to the No. 2 output shaft.

SST
09710-04071  

NOTICE:

After installation, make sure that the gear and synchronizer ring move smoothly.



Hide 33322C 14.INSTALL NO. 2 OUTPUT SHAFT BEARING SNAP RING

a.
C275898C01
0.771,1.771 1,1.979 1,1.979 1.844,1.979 false 0.615,1.583 0.927,1.781 0.313,0.198 10 *a
*a Mark


Select a new No. 2 output shaft bearing snap ring, using the table below, that makes the thrust clearance of the No. 2 output shaft rear bearing less than 0.1 mm (0.00394 in.).

No. 2 Output Shaft Bearing Snap Ring Thickness:
Mark Thickness mm (in.) Mark Thickness mm (in.)
B 1.85 to 1.90 (0.0728 to 0.0748) 0 2.05 to 2.10 (0.0807 to 0.0827)
C 1.90 to 1.95 (0.0748 to 0.0768) 1 2.10 to 2.15 (0.0827 to 0.0846)
D 1.95 to 2.00 (0.0768 to 0.0787) 2 2.15 to 2.20 (0.0846 to 0.0866)
E 2.00 to 2.05 (0.0787 to 0.0807) - -


b.
C112395

Using a snap ring expander, install the No. 2 output shaft bearing snap ring to the No. 2 output shaft.


Hide 15.INSPECT 6TH DRIVEN GEAR THRUST CLEARANCE

Hide 16.INSPECT 6TH DRIVEN GEAR RADIAL CLEARANCE

Hide 33322B 17.INSTALL NO. 2 OUTPUT SHAFT FRONT BEARING

a.
C112459N01
0.141,0.487 0.467,0.816 0.326,0.329 10 SST 0.941,1.027 0.54,0.588 0.54,0.588 0.998,0.588 false

Using SST and a press, install the No. 2 output shaft front bearing to the No. 2 output shaft.

SST
09309-37010  
09506-30012  


Hide 33321N 18.INSTALL OUTPUT SHAFT FRONT BEARING INNER RACE

a.
C451094

Using SST and a press, install the output shaft front bearing inner race to the No. 1 output shaft.

SST
09710-30012  (09710-04091)


Hide 33335 19.INSTALL 1ST DRIVEN GEAR

a.
C112425

Coat the needle roller bearing with gear oil and install it to the No. 1 output shaft.


b.
C157334C04
2.052,0.417 2.854,0.583 2.854,0.583 2.854,0.854 false 2.792,0.896 3.208,1.094 0.417,0.198 10 *a
*a Inner Ring


Install the inner ring to the 1st driven gear.


c.
C157335C03
2.01,0.25 2.771,0.427 2.771,0.427 2.771,0.688 false 2.719,0.729 3.177,1.208 0.458,0.479 10 *a
*a Middle Ring


Install the middle ring to the 1st driven gear.


d.
C157336C03
2.156,0.323 2.813,0.552 2.813,0.552 2.813,0.833 false 2.75,0.875 3.188,1.156 0.438,0.281 10 *a
*a Outer Ring


Install the outer ring to the 1st driven gear.


e.
C274862

Coat the 1st driven gear with gear oil and install it to the No. 1 output shaft.


Hide 33361 20.INSTALL NO. 1 TRANSMISSION CLUTCH HUB

a.
C451095

Apply gear oil to the No. 1 transmission hub sleeve and No. 1 transmission clutch hub.


b.

Install the No. 1 transmission hub sleeve to the No. 1 transmission clutch hub.


c.

Install the 3 No. 1 synchromesh shifting keys to the No. 1 transmission clutch hub.


d.

Install the 3 synchronizer shifting key springs to the No. 1 transmission clutch hub.


e.

Place the balls in the holes of the No. 1 synchromesh shifting keys and install the No. 1 transmission hub sleeve while pushing in the balls.

NOTICE:

Take care to prevent the balls from scattering.



f.

Coat the 1st driven gear synchronizer ring set with gear oil.


g.
C112467N01
2.354,1.406 2.229,1.406 2.229,1.406 2.229,1.625 false 2.115,1.635 2.406,1.813 0.292,0.177 10 SST

Using SST and a press, install the No. 1 transmission hub sleeve to the No. 1 output shaft.

SST
09726-40010  

NOTICE:

After installation, make sure that the gear and synchronizer ring move smoothly.


HINT:

Make sure that the protruding part on the 1st driven gear synchronizer ring set is fitted into the groove of the No. 1 transmission clutch hub.



Hide 33037B 21.INSTALL 2ND DRIVEN GEAR SYNCHRONIZER RING SET

a.
C157337C03
2.031,0.365 2.792,0.583 2.792,0.583 2.792,0.896 false 2.75,0.948 3.167,1.229 0.417,0.281 10 *a
*a Inner Ring


Coat the 2nd driven gear synchronizer ring set with gear oil.


b.

Install the inner ring to the 2nd driven gear.


c.
C157338C03
2.052,0.333 2.823,0.563 2.823,0.563 2.823,0.917 false 2.74,0.948 3.219,1.24 0.479,0.292 10 *a
*a Middle Ring


Install the middle ring to the 2nd driven gear.


d.
C157339C03
2.156,0.323 2.823,0.521 2.823,0.521 2.823,0.771 false 2.781,0.823 3.188,1.094 0.406,0.271 10 *a
*a Outer Ring


Install the outer ring to the 2nd driven gear.


Hide 33365C 22.INSTALL SYNCHROMESH SHIFTING KEY BALL

a.
C116562

Install the synchromesh shifting key ball to the No. 1 output shaft.


Hide 33332B 23.INSTALL NEEDLE ROLLER BEARING

a.
C112421

Coat the needle roller bearing with gear oil and install it to the No. 1 output shaft.


Hide 33332 24.INSTALL 2ND DRIVEN GEAR

a.
C112420

Coat the 2nd driven gear with gear oil and install it to the No. 1 output shaft.


Hide 33356A 25.INSTALL 2ND DRIVEN GEAR BEARING INNER RACE

a.
C112419

Align the groove of the 2nd driven gear bearing inner race with the ball and install the inner race.


Hide 33321C 26.INSTALL OUTPUT SHAFT BEARING SHAFT SNAP RING

a.
C275848C01
2.573,0.948 3.094,1.292 3.094,1.292 3.094,1.531 false 3.01,1.583 3.323,1.781 0.313,0.198 10 *a
*a Mark


Select a new output shaft bearing shaft snap ring, using the table below, that makes the thrust clearance of the 2nd driven gear bearing inner race less than 0.1 mm (0.00394 in.).

Output Shaft Bearing Shaft Snap Ring Thickness:
Mark Thickness mm (in.) Mark Thickness mm (in.)
A 2.25 to 2.30 (0.0886 to 0.0906) E 2.45 to 2.50 (0.0965 to 0.0984)
B 2.30 to 2.35 (0.0906 to 0.0925) F 2.50 to 2.55 (0.0984 to 0.1004)
C 2.35 to 2.40 (0.0925 to 0.0945) G 2.55 to 2.60 (0.1004 to 0.1024)
D 2.40 to 2.45 (0.0945 to 0.0965) H 2.60 to 2.65 (0.1024 to 0.1043)


b.
C112418

Using a snap ring expander, install the output shaft bearing shaft snap ring to the No. 1 output shaft.

HINT:

Do not damage the journal surface of the No. 1 output shaft.



Hide 27.INSPECT 1ST DRIVEN GEAR THRUST CLEARANCE

Hide 28.INSPECT 1ST DRIVEN GEAR RADIAL CLEARANCE

Hide 29.INSPECT 2ND DRIVEN GEAR THRUST CLEARANCE

Hide 30.INSPECT 2ND DRIVEN GEAR RADIAL CLEARANCE

Hide 33422B 31.INSTALL 4TH DRIVEN GEAR

a.
C112417

Install the spacer to the No. 1 output shaft.


b.
C112416

Coat the needle roller bearing with gear oil and install it to the No. 1 output shaft.


c.
C157343C03
2.031,0.458 2.854,0.833 2.854,0.833 2.854,1.135 false 2.781,1.188 3.135,1.479 0.354,0.292 10 *a
*a Inner Ring


Install the inner ring to the 4th driven gear.


d.
C157344C04
2.063,0.438 2.729,0.656 2.729,0.656 2.729,0.938 false 2.677,0.99 3.135,1.25 0.458,0.26 10 *a
*a Middle Ring


Install the middle ring to the 4th driven gear.


e.
C157345C03
2.177,0.448 2.781,0.76 2.781,0.76 2.781,1.042 false 2.74,1.104 3.167,1.427 0.427,0.323 10 *a
*a Outer Ring


Install the outer ring to the 4th driven gear.


f.
C116209

Coat the 4th driven gear with gear oil and install it to the No. 1 output shaft.


Hide 33362 32.INSTALL NO. 2 TRANSMISSION CLUTCH HUB

a.
C451096

Apply gear oil to the No. 2 transmission hub sleeve and No. 2 transmission clutch hub.


b.

Install the No. 2 transmission hub sleeve to the No. 2 transmission clutch hub.


c.

Install the 3 No. 1 synchromesh shifting keys to the No. 2 transmission clutch hub.


d.

Install the 3 synchronizer shifting key springs to the No. 2 transmission clutch hub.


e.

Place the balls in the holes of the No. 1 synchromesh shifting keys and install the No. 2 transmission hub sleeve while pushing in the balls.

NOTICE:

Take care to prevent the balls from scattering.



f.

Coat the 4th driven gear synchronizer ring set with gear oil.


g.
C112468N01
0.691,0.288 1.023,0.634 0.332,0.346 10 SST 1.08,0.385 1.264,0.385 1.264,0.385 1.541,0.609 false

Using SST and a press, install the transmission clutch hub to the 4th driven gear.

SST
09309-14010  

NOTICE:

After installation, make sure that the gear and synchronizer ring move smoothly.


HINT:

Make sure that the protruding part on the 4th driven gear synchronizer ring set is fitted into the groove of the No. 2 transmission clutch hub.



Hide 33352C 33.INSTALL SHAFT SNAP RING

a.
C275849C01
2.51,1.448 2.51,0.542 false 2.458,1.542 2.771,1.74 0.313,0.198 10 *a
*a Mark


Select a new shaft snap ring, using the table below, that makes the thrust clearance of the No. 2 transmission clutch hub less than 0.1 mm (0.00394 in.).

Shaft Snap Ring Thickness:
Mark Thickness mm (in.) Mark Thickness mm (in.)
1 2.25 to 2.30 (0.0886 to 0.0906) 4 2.40 to 2.45 (0.0945 to 0.0965)
2 2.30 to 2.35 (0.0906 to 0.0925) 5 2.45 to 2.50 (0.0965 to 0.0984)
3 2.35 to 2.40 (0.0925 to 0.0945) 6 2.50 to 2.55 (0.0984 to 0.1004)


b.
C112469

Using a brass bar and hammer, tap the shaft snap ring to the No. 1 output shaft.


Hide 34.INSPECT 4TH DRIVEN GEAR THRUST CLEARANCE

Hide 35.INSPECT 4TH DRIVEN GEAR RADIAL CLEARANCE

Hide 33423A 36.INSTALL 3RD DRIVEN GEAR

a.
C157340C03
2.01,0.427 2.688,0.698 2.688,0.698 2.688,0.969 false 2.625,1.01 3.104,1.281 0.479,0.271 10 *a
*a Inner Ring


Coat the 3rd driven gear synchronizer ring set with gear oil.


b.

Install the inner ring to the 3rd driven gear.


c.
C157341C03
2.073,0.365 2.875,0.698 2.875,0.698 2.875,0.958 false 2.792,1 3.177,1.323 0.385,0.323 10 *a
*a Middle Ring


Install the middle ring to the 3rd driven gear.


d.
C157342C03
2.177,0.438 2.844,0.74 2.844,0.74 2.844,1.063 false 2.792,1.115 3.156,1.51 0.365,0.396 10 *a
*a Outer Ring


Install the outer ring to the 3rd driven gear.


e.
C112412

Coat the needle roller bearing with gear oil and install it to the No. 1 output shaft.


f.
C112411

Install the spacer to the No. 1 output shaft.


g.
C112410

Coat the 3rd driven gear with gear oil and install it to the No. 1 output shaft.


Hide 33321A 37.INSTALL OUTPUT SHAFT REAR BEARING

a.
C451097N01
1.125,0.219 1.583,0.479 false 0.833,0.115 1.292,0.313 0.458,0.198 10 false SST

Using SST and a press, install the output shaft rear bearing to the No. 1 output shaft.

SST
09308-14010  

NOTICE:

After installation, make sure that the gear and synchronizer ring move smoothly.


HINT:

When pressing in the bearing, apply force only to the inner race. Do not apply force to the seal.



Hide 33321C 38.INSTALL OUTPUT SHAFT BEARING SHAFT SNAP RING

a.
C451098C01
2.792,1.208 2.969,0.76 false 2.667,1.198 2.979,1.396 0.313,0.198 10 false *a
*a Mark


Select a new output shaft bearing shaft snap ring, using the table below, that makes the thrust clearance of the output shaft rear bearing less than 0.1 mm (0.00394 in.).

Output Shaft Bearing Shaft Snap Ring Thickness:
Mark Thickness mm (in.) Mark Thickness mm (in.)
B 1.85 to 1.90 (0.0728 to 0.0748) 0 2.05 to 2.10 (0.0807 to 0.0827)
C 1.90 to 1.95 (0.0748 to 0.0768) 1 2.10 to 2.15 (0.0827 to 0.0846)
D 1.95 to 2.00 (0.0768 to 0.0787) 2 2.15 to 2.20 (0.0846 to 0.0866)
E 2.00 to 2.05 (0.0787 to 0.0807) - -


b.
C451089

Using a snap ring expander, install the output shaft bearing shaft snap ring to the No. 1 output shaft.


Hide 39.INSPECT 3RD DRIVEN GEAR THRUST CLEARANCE

Hide 40.INSPECT 3RD DRIVEN GEAR RADIAL CLEARANCE