These DTCs are stored when a malfunction occurs in the active noise control microphone LH system.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B1AA296 | Front Left Microphone Circuit Component Internal Failure | Stereo component equalizer assembly detects malfunction in active noise control microphone LH for 4 seconds or more continuously when engine speed is 1200 rpm or more* | ·
Harness or connector ·
Active noise control microphone LH ·
Stereo component equalizer assembly |
| B1AA31C | Front Left Microphone Circuit Circuit Voltage Out of Range | Stereo component equalizer assembly detects active noise control microphone LH connection malfunction for 4 seconds or more continuously* | ·
Harness or connector ·
Active noise control microphone LH ·
Stereo component equalizer assembly |
*: Malfunction monitoring is not performed under the following conditions, in order to prevent erroneous detection.
After ignition switch is turned to ACC for 3 seconds or more.
After the auxiliary battery voltage returns to normal for 3 seconds.
Before 3 seconds have elapsed after auxiliary battery voltage has returned to normal.
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC B1AA296 and B1AA31C are not output | A |
| DTC B1AA296 and B1AA31C are output | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| w/ Stereo Component Amplifier Assembly | A |
| w/o Stereo Component Amplifier Assembly | B |
A
B
Disconnect the O124 stereo component equalizer assembly connector.
Disconnect the V12 active noise control microphone LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O124-7 (MC1+) - V12-1 (MC1+) | Always | Below 1 Ω |
| O124-21 (MC1-) - V12-2 (MC1-) | Always | Below 1 Ω |
| O124-7 (MC1+) - Body ground | Always | 10 kΩ or higher |
| O124-21 (MC1-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the active noise control microphone LH with a new or known good one.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>ACTIVE NOISE CONTROL MICROPHONE>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC B1AA296 and B1AA31C are not output | A |
| DTC B1AA296 and B1AA31C are output | B |
A
B
Disconnect the O132 stereo component equalizer assembly connector.
Disconnect the V12 active noise control microphone LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O132-1 (MC1+) - V12-1 (MC1+) | Always | Below 1 Ω |
| O132-5 (MC1-) - V12-2 (MC1-) | Always | Below 1 Ω |
| O132-1 (MC1+) - Body ground | Always | 10 kΩ or higher |
| O132-5 (MC1-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the active noise control microphone LH with a new or known good one.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>ACTIVE NOISE CONTROL MICROPHONE>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC B1AA296 and B1AA31C are not output | A |
| DTC B1AA296 and B1AA31C are output | B |
A
B