Home › Audio / Visual / Telematics › AUDIO / VIDEO › ACTIVE NOISE CONTROL SYSTEM › from 2020.09
RM36W0E _56 Audio / Visual / Telematics _088597 AUDIO / VIDEO _0449775 ACTIVE NOISE CONTROL SYSTEM C

AUDIO / VIDEO  ACTIVE NOISE CONTROL SYSTEM  P033531  Crankshaft Position Sensor "A" No Signal  


DESCRIPTION

This DTC is output when a malfunction has occurred in the engine pulse signal system from the ECM.

DTC No. Detection Item DTC Detection Condition Trouble Area
P033531 Crankshaft Position Sensor "A" No Signal Stereo component equalizer assembly detects malfunction in engine pulse signal system for 10 seconds or more continuously when engine speed is between 500 and 6000 rpm*
·

Harness or connector

·

ECM

·

Stereo component equalizer assembly



HINT:

*: Malfunction monitoring is not performed under the following conditions, in order to prevent erroneous detection.

·

After ignition switch is turned to ACC for 3 seconds or more.

·

After the auxiliary battery voltage returns to normal for 3 seconds.

·

Before 3 seconds have elapsed after auxiliary battery voltage has returned to normal.



WIRING DIAGRAM

w/ Stereo Component Amplifier Assembly
E364742E12
0.958,1 1.417,1.198 0.458,0.198 10 false NEO 1.406,0.885 1.667,1.115 0.26,0.229 10 false 16 0.521,1.917 1.021,2.125 0.5,0.208 10 false A106 0.521,2.104 0.979,2.302 0.458,0.198 10 false ECM 5.802,1.021 6.26,1.219 0.458,0.198 10 false NEI 5.563,0.927 5.719,1.115 0.156,0.188 10 false 3 5.74,1.917 6.198,2.115 0.458,0.198 10 false O124 5.74,2.094 7,2.5 1.26,0.406 10 false Stereo Component Equalizer Assembly

w/ o Stereo Component Amplifier Assembly
E364742E13
1.031,1.042 1.49,1.24 0.458,0.198 10 false NEO 1.417,0.906 1.646,1.125 0.229,0.219 10 false 16 5.552,0.906 5.781,1.125 0.229,0.219 10 false 3 5.792,1.042 6.24,1.208 0.448,0.167 10 false NEI 5.708,1.917 6.177,2.104 0.469,0.188 10 false O131 0.542,1.938 0.948,2.146 0.406,0.208 10 false A106 0.563,2.125 1.063,2.333 0.5,0.208 10 false ECM 5.708,2.094 6.969,2.49 1.26,0.396 10 false Stereo Component Equalizer Assembly

CAUTION / NOTICE / HINT

NOTICE:

The active noise control system troubleshooting procedure is based on the premise that the stop and start system*, SFI system and entry and start system is operating normally. Check the stop and start system*, SFI system and entry and start system first before troubleshooting the active noise control system.

*: w/ Stop and Start System


PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Active Noise Control > Clear DTCs
50002 415

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Active Noise Control > Trouble Codes
50001 415
OK:

DTC P033531 is not output.



Result:
Result Proceed to
DTC P033531 is not output A
DTC P033531 is output B



A

B

3.CHECK FOR MODEL
3.CHECK FOR MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
w/ Stereo Component Amplifier Assembly A
w/o Stereo Component Amplifier Assembly B



A

4.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT EQUALIZER ASSEMBLY - ECM)

B

5.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT EQUALIZER ASSEMBLY - ECM)
4.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT EQUALIZER ASSEMBLY - ECM)
a.

Disconnect the O124 stereo component equalizer assembly connector.


b.

Disconnect the A106 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O124-3 (NEI) - A106-16 (NEO) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE STEREO COMPONENT EQUALIZER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT EQUALIZER ASSEMBLY - ECM)
a.

Disconnect the O131 stereo component equalizer assembly connector.


b.

Disconnect the A106 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O131-3 (NEI) - A106-16 (NEO) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE STEREO COMPONENT EQUALIZER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR