Home › Engine / Hybrid System › G16E-GTS (ENGINE CONTROL) › CAMSHAFT OIL CONTROL SOLENOID › from 2020.09
RM36W0E _51 Engine / Hybrid System _095127 G16E-GTS ENGINE CONTROL _0449855 CAMSHAFT OIL CONTROL SOLENOID G

G16E-GTS ENGINE CONTROL  CAMSHAFT OIL CONTROL SOLENOID  INSPECTION  


PROCEDURE

Hide 15370 1.INSPECT CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Intake Side)

a.

Check the resistance.

i.
A436353C17
1.51,0.135 1.927,0.344 0.417,0.208 0.125,0.094 0.396,0.333 0.271,0.24 10 false *a 1.604,0.167 1.938,0.406 0.333,0.24 10 false D92
*a Component without harness connected
(Camshaft Timing Oil Control Solenoid Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D92-1 - D92-2 0 °C (32 °F) 6.3 to 7.3 Ω
D92-1 - D92-2 20 °C (68 °F) 6.9 to 7.9 Ω
D92-1 - D92-2 40 °C (104 °F) 7.4 to 8.6 Ω


If the result is not as specified, replace the camshaft timing oil control solenoid assembly.



b.

Stroke Amount Inspection

i.
A436356C05
1.198,1.344 1.583,1.344 false 1.188,2.229 1.573,2.229 false 0.125,0.333 0.438,0.49 0.313,0.156 10 false *a 0.146,2.542 0.458,2.698 0.313,0.156 10 false *b 1.021,1.281 1.333,1.438 0.313,0.156 10 false *c 1.01,2.156 1.323,2.313 0.313,0.156 10 false *c 2.25,1.208 2.563,1.365 0.313,0.156 10 false A 2.24,2.26 2.552,2.417 0.313,0.156 10 false B
*a Shaft Side Facing Down
*b Shaft Side Facing Up
*c Shaft


Using vernier calipers, measure length (A) and (B) with the shaft of the camshaft timing oil control solenoid assembly set in the respective positions shown in the illustration.

NOTICE:

Do not apply auxiliary battery voltage to the terminals of the camshaft timing oil control solenoid assembly .


HINT:

If the shaft does not extend under its own weight, extend the shaft with your fingers.



ii.

Calculate the stroke amount based on the difference of length (A) and (B).

Standard:

4.3 mm (0.169 in.) or more


HINT:

Stroke amount = length (A) - length (B)


If the value is not as specified, replace the camshaft timing oil control solenoid assembly .



Hide 15370 2.INSPECT CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Exhaust Side)

a.

Check the resistance.

i.
A436353C18
1.51,0.135 1.927,0.344 0.417,0.208 0.125,0.094 0.396,0.333 0.271,0.24 10 false *a 1.625,0.167 1.896,0.406 0.271,0.24 10 false D17
*a Component without harness connected
(Camshaft Timing Oil Control Solenoid Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D17-1 - D17-2 0 °C (32 °F) 6.3 to 7.3 Ω
D17-1 - D17-2 20 °C (68 °F) 6.9 to 7.9 Ω
D17-1 - D17-2 40 °C (104 °F) 7.4 to 8.6 Ω


If the result is not as specified, replace the camshaft timing oil control solenoid assembly.



b.

Stroke Amount Inspection

i.
A436356C05
1.198,1.344 1.583,1.344 false 1.188,2.229 1.573,2.229 false 0.125,0.333 0.438,0.49 0.313,0.156 10 false *a 0.146,2.542 0.458,2.698 0.313,0.156 10 false *b 1.021,1.281 1.333,1.438 0.313,0.156 10 false *c 1.01,2.156 1.323,2.313 0.313,0.156 10 false *c 2.25,1.208 2.563,1.365 0.313,0.156 10 false A 2.24,2.26 2.552,2.417 0.313,0.156 10 false B
*a Shaft Side Facing Down
*b Shaft Side Facing Up
*c Shaft


Using vernier calipers, measure length (A) and (B) with the shaft of the camshaft timing oil control solenoid assembly set in the respective positions shown in the illustration.

NOTICE:

Do not apply auxiliary battery voltage to the terminals of the camshaft timing oil control solenoid assembly .


HINT:

If the shaft does not extend under its own weight, extend the shaft with your fingers.



ii.

Calculate the stroke amount based on the difference of length (A) and (B).

Standard:

4.3 mm (0.169 in.) or more


HINT:

Stroke amount = length (A) - length (B)


If the value is not as specified, replace the camshaft timing oil control solenoid assembly .