Home › Engine / Hybrid System › G16E-GTS (INTAKE / EXHAUST) › INTAKE SYSTEM › from 2020.09
RM36W0E _51 Engine / Hybrid System _095906 G16E-GTS INTAKE / EXHAUST _0449871 INTAKE SYSTEM G

G16E-GTS INTAKE / EXHAUST  INTAKE SYSTEM  ON-VEHICLE INSPECTION  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced when repairing air leaks in the intake system are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Air leak from intake system is repaired Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

PROCEDURE

Hide 1.INSPECT INTAKE SYSTEM

CAUTION:
A345137

To prevent injury due to contact with an operating cooling fan, keep your hands and clothing away from the cooling fans when working in the engine compartment with the engine running or the engine switch on (IG).


HINT:

Perform "Inspection After Repair" after repairing vacuum leaks in the intake system.

Click hereEngine / Hybrid System>G16E-GTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.

Check that there are no vacuum leaks at the points shown in the illustration.

A476308


Hide 2.PERFORM INITIALIZATION

a.

Perform "Inspection After Repair" after repairing vacuum leaks in the intake system.

Click hereEngine / Hybrid System>G16E-GTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


Hide 3.INSPECT INTAKE AIR CONTROL VALVE ACTUATOR

a.
A489279

Disconnect the vacuum hose from the intake air control valve actuator.


b.
A490417C01
2.396,1.396 2.531,1.792 2.531,1.792 2.708,1.792 true 1.302,1.771 1.302,1.573 1.302,1.573 1.521,1.448 true 1.313,4.365 1.313,4.208 1.313,4.208 1.542,4.083 true 2.448,4.135 2.615,4.427 2.615,4.427 2.792,4.427 true 0.073,0.052 0.385,0.208 0.313,0.156 10 true *a 0.104,2.833 0.417,2.99 0.313,0.156 10 true *b 1.167,1.771 1.479,1.927 0.313,0.156 10 true *c 2.802,4.354 3.115,4.51 0.313,0.156 10 true *d 1.177,4.354 1.49,4.51 0.313,0.156 10 true *c 2.719,1.708 3.031,1.865 0.313,0.156 10 true *d
*a Vacuum released
*b Vacuum applied
*c Intake Air Control Valve Actuator
*d Intake Air Control Valve


Confirm that the intake air control valve opens smoothly under vacuum and closes smoothly when the vacuum is released.

If the intake air control valve does not close or open smoothly, replace the air cleaner assembly.


c.

Connect the vacuum hose to the intake air control valve actuator.


Hide 4.INSPECT VACUUM SWITCHING VALVE ASSEMBLY (for AICV)

a.
A490418

Disconnect the vacuum switching valve assembly (for AICV) connector.


b.

Disconnect the 2 vacuum hoses from the vacuum switching valve assembly (for AICV).


c.
A490419C01
0.708,3.135 0.875,3.135 0.875,3.135 0.927,3.521 true 1.271,0.125 1.479,0.281 0.208,0.156 10 false *a 0.5,3.031 0.729,3.208 0.229,0.177 10 false *b
*a Component without harness connected
(Vacuum Switching Valve Assembly (for AICV))
*b Body Ground


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 37 to 44 Ω
D98-1 - Body ground Always 10 kΩ or higher
D98-2 - Body ground Always 10 kΩ or higher


If the result is not as specified, replace the air cleaner assembly.


d.

Check the operation of the vacuum switching valve assembly (for AICV).

i.
A490420C01
0.979,0.417 1.188,0.417 1.188,0.417 1.49,1.031 false 0.5,2 0.635,2 0.635,2 0.667,1.625 true 0.719,0.323 1.031,0.646 0.313,0.323 10 false *a 0.271,1.917 0.604,2.208 0.333,0.292 10 false *b 2.521,0.5 2.906,0.792 0.385,0.292 10 false *c
*a Filter
*b Port (E)
*c Air


When vacuum is applied to the port (E), check that air is sucked into the filter.

If air is not sucked into the filter, replace the air cleaner assembly.


ii.
A490421C01
1.531,1.208 1.365,1.208 1.365,1.208 0.938,0.99 true 0.333,1.167 0.5,1.167 0.5,1.167 0.573,0.906 true 1.583,1.104 1.906,1.438 0.323,0.333 10 false *a 0.135,1.073 0.448,1.354 0.313,0.281 10 false *b 1.396,1.667 1.698,1.896 0.302,0.229 10 false *c
*a Port (E)
*b Port (F)
*c Air


Apply battery voltage across the terminals. When vacuum is applied to the port (F), check that air is sucked into the port (E).

If air is not sucked into the port (F), replace the air cleaner assembly.