This circuit provides power to operate the blind spot monitor sensor.
Inspect the fuses for circuits related to this system before performing the following procedure.
Check the vehicle specifications.
| Result | Proceed to |
|---|---|
| for TMC Made with 5 Door | A |
| except TMC Made with 5 Door | B |
A
B
Disconnect the T6 blind spot monitor sensor LH (B) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| T6-5 (BLB) - Body ground | Ignition switch ON | 11 to 14 V |
| T6-5 (BLB) - Body ground | Ignition switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the T6 blind spot monitor sensor LH (B) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| T6-10 (BLGD) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the S6 blind spot monitor sensor RH (A) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| S6-5 (BRB) - Body ground | Ignition switch ON | 11 to 14 V |
| S6-5 (BRB) - Body ground | Ignition switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the S6 blind spot monitor sensor RH (A) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S6-10 (BRGD) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the O38 blind spot monitor sensor LH (B) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| O38-5 (BLB) - Body ground | Ignition switch ON | 11 to 14 V |
| O38-5 (BLB) - Body ground | Ignition switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the O38 blind spot monitor sensor LH (B) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O38-10 (BLGD) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the O37 blind spot monitor sensor RH (A) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| O37-5 (BRB) - Body ground | Ignition switch ON | 11 to 14 V |
| O37-5 (BRB) - Body ground | Ignition switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the O37 blind spot monitor sensor RH (A) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O37-10 (BRGD) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG