Home › Drivetrain › CLUTCH › CLUTCH PEDAL SWITCH › from 2020.09
RM36W0E _52 Drivetrain _089426 CLUTCH _0424694 CLUTCH PEDAL SWITCH G

CLUTCH  CLUTCH PEDAL SWITCH  INSPECTION  


PROCEDURE

Hide 84520 1.INSPECT CLUTCH START SWITCH ASSEMBLY

a.

Check the resistance.

i.
C271613C10
1.229,0.042 1.729,0.292 0.5,0.25 1.031,1.448 1.365,0.958 true 1.01,0.229 1.354,0.635 true 0.094,0.135 0.406,0.292 0.313,0.156 10 false *a 1.99,1.635 2.302,1.792 0.313,0.156 10 false *c 2.969,1.646 3.219,1.802 0.25,0.156 10 false *d 0.917,1.479 1.063,1.719 0.146,0.24 10 false L 0.854,0.073 1,0.271 0.146,0.198 10 false B 1.354,0.073 1.813,0.271 0.458,0.198 10 false A64 1.688,1.375 2,1.531 0.313,0.156 10 false *b 1.365,0.833 1.51,1.073 0.146,0.24 10 false 1 1.365,0.615 1.51,0.854 0.146,0.24 10 false 2
*a Component without harness connected
(Clutch Start Switch Assembly)
*b 11.65 to 12.35 mm (0.459 to 0.486 in.)
*c On
*d Off


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A64-1 (L) - A64-2 (B) On (Pushed in) Below 1 Ω
A64-1 (L) - A64-2 (B) Off (Released) 10 kΩ or higher


If the result is not as specified, replace the clutch start switch assembly.



Hide 88280A 2.INSPECT CLUTCH SWITCH ASSEMBLY (except G16E-GTS)

a.

Check the resistance.

i.
C330179C02
0.375,1.094 0.885,1.281 0.51,0.188 0.333,2.042 0.49,1.75 true 1.031,2.021 0.792,1.76 true 2.948,1.156 3.344,2.01 0.396,0.854 10 false *b 0.052,0.042 0.406,0.385 0.354,0.344 10 false *a 1.99,1.656 2.313,1.958 0.323,0.302 10 false *c 2.969,1.688 3.344,2.052 0.375,0.365 10 false *d 0.5,1.104 0.958,1.302 0.458,0.198 10 false A65 1.073,1.979 1.531,2.177 0.458,0.198 10 false CL+ 0.104,1.979 0.563,2.177 0.458,0.198 10 false CL-
*a Component without harness connected
(Clutch Switch Assembly)
*b 6.5 to 7.5 mm (0.256 to 0.295 in.)
*c On
*d Off


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A65-1 (CL+) - A65-2 (CL-) On (Pushed in) Below 1 Ω
A65-1 (CL+) - A65-2 (CL-) Off (Released) 10 kΩ or higher


If the result is not as specified, replace the clutch switch assembly.