Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2020.09
RM36W0E _58 Vehicle Interior _088020 SUPPLEMENTAL RESTRAINT SYSTEMS _0420309 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B009083  Left Frontal Restraints Sensor Value of Signal Protection Calculation Incorrect  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Test Mode / Check Mode
B009083 Left Frontal Restraints Sensor Value of Signal Protection Calculation Incorrect
·

The airbag sensor assembly detects a line short in the front airbag sensor LH circuit for 2 seconds

·

The airbag sensor assembly detects a short to ground in the front airbag sensor LH circuit for 2 seconds

·

The airbag sensor assembly detects a short to B+ in the front airbag sensor LH circuit for 2 seconds

·

The airbag sensor assembly detects an open in the front airbag sensor LH circuit for 2 seconds

·

Front airbag sensor LH malfunction

·

Airbag sensor assembly malfunction


·

Harness or connector

·

Front airbag sensor LH

·

Airbag sensor assembly


Comes on Does not apply to test/check mode

WIRING DIAGRAM

B473434E50
4.781,2.896 6.854,3.365 2.073,0.469 10 false Airbag Sensor Assembly 4.771,2.719 5.271,2.906 0.5,0.188 10 false H14 4.583,1.021 5.042,1.323 0.458,0.302 10 false 30 4.583,1.698 5.333,2.073 0.75,0.375 10 false 31 4.833,1.021 5.292,1.323 0.458,0.302 10 false +SL 4.844,1.698 5.594,2.073 0.75,0.375 10 false -SL 5.479,1.448 6.156,1.74 0.677,0.292 10 false Interface 1.771,1.448 2.448,1.74 0.677,0.292 10 false Interface 0.76,1.448 1.438,1.74 0.677,0.292 10 false Element 3.042,1.021 3.5,1.323 0.458,0.302 10 false 2 3.042,1.708 3.5,2.01 0.458,0.302 10 false 1 2.667,1.021 3.125,1.323 0.458,0.302 10 false +SL 2.708,1.708 3.458,2.083 0.75,0.375 10 false -SL 0.563,2.344 1.031,2.521 0.469,0.177 10 false A41 0.563,2.521 2.635,2.99 2.073,0.469 10 false Front Airbag Sensor LH

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting the cable from the negative (-) auxiliary battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the cable to the auxiliary battery terminal, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




PROCEDURE

1.CHECK CONNECTION OF CONNECTORS

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



Procedure1

c.

Check that the connectors are properly connected to the airbag sensor assembly and front airbag sensor LH.

OK:

The connectors are properly connected.


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

2.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

2.CHECK CONNECTORS

Pre-procedure1

a.

Disconnect the connectors from the airbag sensor assembly and front airbag sensor LH.


Procedure1

b.
C422859C02
1.521,0.563 1.521,0.99 false 2.625,0.969 2.958,1.313 0.333,0.344 10 false *2 1.448,0.385 1.781,0.542 0.333,0.156 10 false *3 0.406,0.969 0.615,1.208 0.208,0.24 10 false *1
*1 Front Airbag Sensor LH
*2 Airbag Sensor Assembly
*3 Wire Harness


Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals of the connectors are not deformed or damaged.


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

3.CHECK WIRE HARNESS (SHORT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK WIRE HARNESS (SHORT)
a.
C431634C03
0.833,2.167 1.177,2.396 0.344,0.229 1.427,2.698 1.74,2.313 true 2.313,2.698 1.948,2.313 true 1.625,0.865 1.625,0.615 false 0.563,0.875 0.833,1.083 0.271,0.208 10 false *1 2.698,0.875 3,1.167 0.302,0.292 10 false *2 1.552,0.438 1.813,0.604 0.26,0.167 10 false *3 0.667,1.771 1,2 0.333,0.229 10 false *a 2.24,0.875 2.417,1.083 0.177,0.208 10 false A 1.885,0.875 2.083,1.083 0.198,0.208 10 false B 1.292,0.875 1.5,1.083 0.208,0.208 10 false C 0.938,0.875 1.167,1.083 0.229,0.208 10 false D 0.896,2.219 1.167,2.396 0.271,0.177 10 false A41 2.229,2.75 2.667,2.917 0.438,0.167 10 false +SL 1.281,2.75 1.75,3 0.469,0.25 10 false -SL
*1 Front Airbag Sensor LH
*2 Airbag Sensor Assembly
*3 Wire Harness
*a Front view of wire harness connector
(to Front Airbag Sensor LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A41-2 (+SL) - A41-1 (-SL) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK WIRE HARNESS (SHORT TO GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK WIRE HARNESS (SHORT TO GROUND)
a.
C431634C03
0.833,2.167 1.177,2.396 0.344,0.229 1.427,2.698 1.74,2.313 true 2.313,2.698 1.948,2.313 true 1.625,0.865 1.625,0.615 false 0.563,0.875 0.833,1.083 0.271,0.208 10 false *1 2.698,0.875 3,1.167 0.302,0.292 10 false *2 1.552,0.438 1.813,0.604 0.26,0.167 10 false *3 0.667,1.771 1,2 0.333,0.229 10 false *a 2.24,0.875 2.417,1.083 0.177,0.208 10 false A 1.885,0.875 2.083,1.083 0.198,0.208 10 false B 1.292,0.875 1.5,1.083 0.208,0.208 10 false C 0.938,0.875 1.167,1.083 0.229,0.208 10 false D 0.896,2.219 1.167,2.396 0.271,0.177 10 false A41 2.229,2.75 2.667,2.917 0.438,0.167 10 false +SL 1.281,2.75 1.75,3 0.469,0.25 10 false -SL
*1 Front Airbag Sensor LH
*2 Airbag Sensor Assembly
*3 Wire Harness
*a Front view of wire harness connector
(to Front Airbag Sensor LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A41-2 (+SL) - Body ground Always 1 MΩ or higher
A41-1 (-SL) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK WIRE HARNESS (OPEN)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK WIRE HARNESS (OPEN)

Pre-procedure1

a.
C422832C02
0.865,0.802 1.219,1.021 0.354,0.219 0.708,3.74 1.063,3.958 0.354,0.219 1.854,1.813 1.854,1.708 false 1.49,1.677 1.792,1.302 true 2.208,1.677 1.906,1.302 true 1.208,4.24 1.531,3.833 true 2.073,4.24 1.74,3.833 true 1.656,3.031 1.656,2.74 false 0.406,2.573 0.667,2.813 0.26,0.24 10 false *1 2.729,2.583 3.104,3.031 0.375,0.448 10 false *2 1.792,1.813 2.094,1.979 0.302,0.167 10 false *4 0.677,0.188 1,0.5 0.323,0.313 10 false *b 0.677,3.427 0.927,3.688 0.25,0.26 10 false *a 2.365,2.583 2.5,2.792 0.135,0.208 10 false A 1.99,2.583 2.125,2.781 0.135,0.198 10 false B 1.146,2.583 1.281,2.781 0.135,0.198 10 false C 0.781,2.583 0.906,2.76 0.125,0.177 10 false D 0.917,0.823 1.323,1.094 0.406,0.271 10 false H14 1.302,1.688 1.656,1.938 0.354,0.25 10 false +SL 2.167,1.688 2.542,1.927 0.375,0.24 10 false -SL 0.76,3.76 1.052,3.938 0.292,0.177 10 false A41 1.99,4.25 2.406,4.479 0.417,0.229 10 false +SL 1.073,4.25 1.49,4.479 0.417,0.229 10 false -SL 1.583,3.042 1.917,3.229 0.333,0.188 10 false *3
*1 Front Airbag Sensor LH
*2 Airbag Sensor Assembly
*3 Wire Harness
*4 Service Wire
*a Front view of wire harness connector
(to Front Airbag Sensor LH)
*b Front view of wire harness connector
(to Airbag Sensor Assembly)


Using a service wire, connect terminals 30 (+SL) and 31 (-SL) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A41-2 (+SL) - A41-1 (-SL) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

c.

Disconnect the service wire from connector B.



OK

6.CHECK WIRE HARNESS (SHORT TO B+)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK WIRE HARNESS (SHORT TO B+)

Pre-procedure1

a.

Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the ignition switch to ON.


Procedure1

c.
C431634C03
0.833,2.167 1.177,2.396 0.344,0.229 1.427,2.698 1.74,2.313 true 2.313,2.698 1.948,2.313 true 1.625,0.865 1.625,0.615 false 0.563,0.875 0.833,1.083 0.271,0.208 10 false *1 2.698,0.875 3,1.167 0.302,0.292 10 false *2 1.552,0.438 1.813,0.604 0.26,0.167 10 false *3 0.667,1.771 1,2 0.333,0.229 10 false *a 2.24,0.875 2.417,1.083 0.177,0.208 10 false A 1.885,0.875 2.083,1.083 0.198,0.208 10 false B 1.292,0.875 1.5,1.083 0.208,0.208 10 false C 0.938,0.875 1.167,1.083 0.229,0.208 10 false D 0.896,2.219 1.167,2.396 0.271,0.177 10 false A41 2.229,2.75 2.667,2.917 0.438,0.167 10 false +SL 1.281,2.75 1.75,3 0.469,0.25 10 false -SL
*1 Front Airbag Sensor LH
*2 Airbag Sensor Assembly
*3 Wire Harness
*a Front view of wire harness connector
(to Front Airbag Sensor LH)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A41-2 (+SL) - Body ground Ignition switch ON Below 1 V
A41-1 (-SL) - Body ground Ignition switch ON Below 1 V


Result:
Proceed to
OK
NG



Post-procedure1

d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.




OK

7.CHECK FRONT AIRBAG SENSOR LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK FRONT AIRBAG SENSOR LH
a.
C422833C02
2.094,1 2.219,1.188 0.125,0.188 10 false A 1.938,1 2.083,1.271 0.146,0.271 10 false B 1.083,1.01 1.219,1.198 0.135,0.188 10 false C 0.927,1.01 1.042,1.229 0.115,0.219 10 false D 0.563,1.021 0.833,1.271 0.271,0.25 10 false *1 2.542,1.031 2.906,1.292 0.365,0.26 10 false *2
*1 Front Airbag Sensor RH
*2 Airbag Sensor Assembly


Connect the connector to the airbag sensor assembly.


b.

Interchange the front airbag sensor LH with RH and connect the connectors.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

f.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

8.CHECK FRONT AIRBAG SENSOR LH
8.CHECK FRONT AIRBAG SENSOR LH

Pre-procedure1

a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

b.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444
HINT:

Codes other than DTCs B009083 and B009583 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
B009083 is output A
B009583 is output B
B009083 and B009583 are not output C


Post-procedure1

c.

Turn the ignition switch off.


d.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



e.

Return the front airbag sensor LH and RH to their original positions and connect the connectors.



A

B

C