Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2020.09
RM36W0E _58 Vehicle Interior _088020 SUPPLEMENTAL RESTRAINT SYSTEMS _0420309 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B009283  Left Side Restraints Sensor 2 Value of Signal Protection Calculation Incorrect  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Test Mode / Check Mode
B009283 Left Side Restraints Sensor 2 Value of Signal Protection Calculation Incorrect
·

The airbag sensor assembly detects a line short in the side collision sensor LH circuit (bus 2) for 2 seconds

·

The airbag sensor assembly detects a short to ground in the side collision sensor LH circuit (bus 2) for 2 seconds

·

The airbag sensor assembly detects a short to B+ in the side collision sensor LH circuit (bus 2) for 2 seconds

·

The airbag sensor assembly detects an open in the side collision sensor LH circuit (bus 2) for 2 seconds

·

No. 1 side airbag sensor LH malfunction

·

Airbag sensor assembly malfunction


·

Harness or connector

·

No. 1 side airbag sensor LH

·

Airbag sensor assembly


Comes on Does not apply to test/check mode

WIRING DIAGRAM

B473434E51
4.781,2.917 6.5,3.333 1.719,0.417 10 false Airbag Sensor Assembly 4.781,2.74 5.417,2.917 0.635,0.177 10 false O24 4.823,1.01 5.938,1.438 1.115,0.427 10 false BCL+ 5.49,1.458 6.052,1.885 0.563,0.427 10 false Interface 4.552,1.01 4.75,1.25 0.198,0.24 10 false 28 4.823,1.688 5.938,2.115 1.115,0.427 10 false BCL- 4.552,1.688 4.75,2.083 0.198,0.396 10 false 29 2.604,1.01 3.719,1.438 1.115,0.427 10 false BFL+ 2.615,1.698 3.729,2.125 1.115,0.427 10 false BFL- 3.052,1.01 4.167,1.438 1.115,0.427 10 false 2 3.052,1.698 4.167,2.125 1.115,0.427 10 false 1 1.771,1.458 2.354,1.938 0.583,0.479 10 false Interface 0.771,1.458 1.354,1.854 0.583,0.396 10 false Element 0.552,2.344 1.25,2.542 0.698,0.198 10 false O5 0.552,2.521 3.354,2.906 2.802,0.385 10 false No. 1 Side Airbag Sensor LH

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting the cable from the negative (-) auxiliary battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the cable to the auxiliary battery terminal, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




PROCEDURE

1.CHECK CONNECTION OF CONNECTORS

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



Procedure1

c.

Check that the connectors are properly connected to the airbag sensor assembly and No. 1 side airbag sensor LH.

OK:

The connectors are properly connected.


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

2.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

2.CHECK CONNECTORS

Pre-procedure1

a.
C422860C02
1.521,0.438 1.521,0.802 false 2.635,1.083 2.938,1.521 0.302,0.438 10 false *2 0.385,0.771 0.667,0.979 0.281,0.208 10 false *1 1.448,0.25 1.75,0.417 0.302,0.167 10 false *3
*1 No. 1 Side Airbag Sensor LH
*2 Airbag Sensor Assembly
*3 Wire Harness


Disconnect the connectors from the airbag sensor assembly and No. 1 side airbag sensor LH.


Procedure1

b.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals of the connectors are not deformed or damaged.


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

3.CHECK WIRE HARNESS (SHORT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK WIRE HARNESS (SHORT)
a.
C422854C04
0.896,2.292 1.24,2.521 0.344,0.229 1.49,2.833 1.802,2.448 true 2.344,2.833 1.979,2.448 true 1.646,0.552 1.646,0.302 false 0.563,0.552 0.802,0.833 0.24,0.281 10 false *1 2.698,0.854 3.01,1.188 0.313,0.333 10 false *2 1.583,0.125 1.844,0.292 0.26,0.167 10 false *3 0.708,1.833 1,2.083 0.292,0.25 10 false *a 2.24,0.552 2.385,0.75 0.146,0.198 10 false A 1.885,0.552 2.083,0.833 0.198,0.281 10 false B 1.292,0.552 1.5,0.75 0.208,0.198 10 false C 0.938,0.552 1.125,0.75 0.188,0.198 10 false D 0.979,2.333 1.25,2.51 0.271,0.177 10 false O5 2.229,2.865 2.75,3.083 0.521,0.219 10 false BFL+ 1.281,2.865 1.75,3.083 0.469,0.219 10 false BFL-
*1 No. 1 Side Airbag Sensor LH
*2 Airbag Sensor Assembly
*3 Wire Harness
*a Front view of wire harness connector
(to No. 1 Side Airbag Sensor LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O5-2 (BFL+) - O5-1 (BFL-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK WIRE HARNESS (SHORT TO GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK WIRE HARNESS (SHORT TO GROUND)
a.
C422854C04
0.896,2.292 1.24,2.521 0.344,0.229 1.49,2.833 1.802,2.448 true 2.344,2.833 1.979,2.448 true 1.646,0.552 1.646,0.302 false 0.563,0.552 0.802,0.833 0.24,0.281 10 false *1 2.698,0.854 3.01,1.188 0.313,0.333 10 false *2 1.583,0.125 1.844,0.292 0.26,0.167 10 false *3 0.708,1.833 1,2.083 0.292,0.25 10 false *a 2.24,0.552 2.385,0.75 0.146,0.198 10 false A 1.885,0.552 2.083,0.833 0.198,0.281 10 false B 1.292,0.552 1.5,0.75 0.208,0.198 10 false C 0.938,0.552 1.125,0.75 0.188,0.198 10 false D 0.979,2.333 1.25,2.51 0.271,0.177 10 false O5 2.229,2.865 2.75,3.083 0.521,0.219 10 false BFL+ 1.281,2.865 1.75,3.083 0.469,0.219 10 false BFL-
*1 No. 1 Side Airbag Sensor LH
*2 Airbag Sensor Assembly
*3 Wire Harness
*a Front view of wire harness connector
(to No. 1 Side Airbag Sensor LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O5-2 (BFL+) - Body ground Always 1 MΩ or higher
O5-1 (BFL-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK WIRE HARNESS (OPEN)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK WIRE HARNESS (OPEN)

Pre-procedure1

a.
C422834C02
0.823,0.833 1.208,1.073 0.385,0.24 0.958,3.729 1.302,3.958 0.344,0.229 1.948,1.813 1.948,1.677 false 1.563,1.729 1.906,1.302 true 2.417,1.74 2.042,1.302 true 1.667,2.854 1.667,2.521 false 1.5,4.271 1.802,3.844 true 2.333,4.271 1.99,3.844 true 0.625,2.375 0.854,2.646 0.229,0.271 10 false *1 2.51,2.656 2.833,2.833 0.323,0.177 10 false *2 1.615,2.865 1.948,3.115 0.333,0.25 10 false *3 1.885,1.823 2.313,2.219 0.427,0.396 10 false *4 0.677,0.188 1.177,0.688 0.5,0.5 10 false *b 0.708,3.427 1.156,3.813 0.448,0.385 10 false *a 2.188,2.375 2.333,2.583 0.146,0.208 10 false A 1.885,2.375 2,2.583 0.115,0.208 10 false B 1.281,2.375 1.49,2.583 0.208,0.208 10 false C 0.979,2.375 1.167,2.583 0.188,0.208 10 false D 1.021,3.75 1.323,3.958 0.302,0.208 10 false O5 0.875,0.854 1.229,1.073 0.354,0.219 10 false O24 2.333,1.74 2.771,2.01 0.438,0.271 10 false BCL- 1.333,1.729 1.781,2.115 0.448,0.385 10 false BCL+ 2.219,4.281 2.667,4.521 0.448,0.24 10 false BFL+ 1.354,4.281 1.792,4.51 0.438,0.229 10 false BFL-
*1 No. 1 Side Airbag Sensor LH
*2 Airbag Sensor Assembly
*3 Wire Harness
*4 Service Wire
*a Front view of wire harness connector
(to No. 1 Side Airbag Sensor LH)
*b Front view of wire harness connector
(to Airbag Sensor Assembly)


Using a service wire, connect terminals 28 (BCL+) and 29 (BCL-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O5-2 (BFL+) - O5-1 (BFL-) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

c.

Disconnect the service wire from connector B.



OK

6.CHECK WIRE HARNESS (SHORT TO B+)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK WIRE HARNESS (SHORT TO B+)

Pre-procedure1

a.

Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the ignition switch to ON.


Procedure1

c.
C422854C04
0.896,2.292 1.24,2.521 0.344,0.229 1.49,2.833 1.802,2.448 true 2.344,2.833 1.979,2.448 true 1.646,0.552 1.646,0.302 false 0.563,0.552 0.802,0.833 0.24,0.281 10 false *1 2.698,0.854 3.01,1.188 0.313,0.333 10 false *2 1.583,0.125 1.844,0.292 0.26,0.167 10 false *3 0.708,1.833 1,2.083 0.292,0.25 10 false *a 2.24,0.552 2.385,0.75 0.146,0.198 10 false A 1.885,0.552 2.083,0.833 0.198,0.281 10 false B 1.292,0.552 1.5,0.75 0.208,0.198 10 false C 0.938,0.552 1.125,0.75 0.188,0.198 10 false D 0.979,2.333 1.25,2.51 0.271,0.177 10 false O5 2.229,2.865 2.75,3.083 0.521,0.219 10 false BFL+ 1.281,2.865 1.75,3.083 0.469,0.219 10 false BFL-
*1 No. 1 Side Airbag Sensor LH
*2 Airbag Sensor Assembly
*3 Wire Harness
*a Front view of wire harness connector
(to No. 1 Side Airbag Sensor LH)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
O5-2 (BFL+) - Body ground Ignition switch ON Below 1 V
O5-1 (BFL-) - Body ground Ignition switch ON Below 1 V


Result:
Proceed to
OK
NG



Post-procedure1

d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.




OK

7.CHECK NO. 1 SIDE AIRBAG SENSOR LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK NO. 1 SIDE AIRBAG SENSOR LH
a.
C422835C02
0.719,0.792 1.073,1.219 0.354,0.427 10 false *1 1.094,0.792 1.24,1.135 0.146,0.344 10 false D 1.25,0.792 1.427,1.125 0.177,0.333 10 false C 1.719,0.792 1.865,1.042 0.146,0.25 10 false B 1.875,0.792 2.052,1.052 0.177,0.26 10 false A 2.323,1.115 2.688,1.406 0.365,0.292 10 false *2
*1 No. 1 Side Airbag Sensor RH
*2 Airbag Sensor Assembly


Connect the connector to the airbag sensor assembly.


b.

Interchange the No. 1 side airbag sensor LH with RH and connect the connectors.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

f.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

8.CHECK NO. 1 SIDE AIRBAG SENSOR LH
8.CHECK NO. 1 SIDE AIRBAG SENSOR LH

Pre-procedure1

a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

b.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444
HINT:

Codes other than DTCs B009283 and B009783 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
B009283 is output A
B009783 is output B
B009283 and B009783 are not output C


Post-procedure1

c.

Turn the ignition switch off.


d.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



e.

Return the No. 1 side airbag sensor LH and RH to their original positions and connect the connectors.



A

B

C