Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2020.09
RM36W0E _58 Vehicle Interior _088020 SUPPLEMENTAL RESTRAINT SYSTEMS _0420309 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B009583  Right Frontal Restraints Sensor Value of Signal Protection Calculation Incorrect  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Test Mode / Check Mode
B009583 Right Frontal Restraints Sensor Value of Signal Protection Calculation Incorrect
·

The airbag sensor assembly detects a line short in the front airbag sensor RH circuit for 2 seconds

·

The airbag sensor assembly detects a short to ground in the front airbag sensor RH circuit for 2 seconds

·

The airbag sensor assembly detects a short to B+ in the front airbag sensor RH circuit for 2 seconds

·

The airbag sensor assembly detects an open in the front airbag sensor RH circuit for 2 seconds

·

Front airbag sensor RH malfunction

·

Airbag sensor assembly malfunction


·

Harness or connector

·

Front airbag sensor RH

·

Airbag sensor assembly


Comes on Does not apply to test/check mode

WIRING DIAGRAM

B473434E52
4.781,2.896 6.854,3.365 2.073,0.469 10 false Airbag Sensor Assembly 4.781,2.74 5.25,2.938 0.469,0.198 10 false H14 4.583,1.021 5.042,1.323 0.458,0.302 10 false 29 4.583,1.698 5.333,2.073 0.75,0.375 10 false 28 4.833,1.021 5.292,1.323 0.458,0.302 10 false +SR 4.844,1.698 5.594,2.073 0.75,0.375 10 false -SR 5.479,1.448 6.156,1.74 0.677,0.292 10 false Interface 1.771,1.448 2.344,1.781 0.573,0.333 10 false Interface 0.76,1.448 1.323,1.76 0.563,0.313 10 false Element 3.042,1.021 3.5,1.323 0.458,0.302 10 false 2 3.042,1.708 3.5,2.01 0.458,0.302 10 false 1 2.667,1.021 3.125,1.323 0.458,0.302 10 false +SR 2.708,1.708 3.458,2.083 0.75,0.375 10 false -SR 0.563,2.344 0.948,2.552 0.385,0.208 10 false A42 0.563,2.521 2.635,2.99 2.073,0.469 10 false Front Airbag Sensor RH

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting the cable from the negative (-) auxiliary battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the cable to the auxiliary battery terminal, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




PROCEDURE

1.CHECK CONNECTION OF CONNECTORS

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



Procedure1

c.

Check that the connectors are properly connected to the airbag sensor assembly and front airbag sensor RH.

OK:

The connectors are properly connected.


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

2.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

2.CHECK CONNECTORS

Pre-procedure1

a.
C422859C02
1.521,0.563 1.521,0.99 false 2.625,0.969 2.958,1.313 0.333,0.344 10 false *2 1.448,0.385 1.781,0.542 0.333,0.156 10 false *3 0.406,0.969 0.615,1.208 0.208,0.24 10 false *1
*1 Front Airbag Sensor RH
*2 Airbag Sensor Assembly
*3 Wire Harness


Disconnect the connectors from the airbag sensor assembly and front airbag sensor RH.


Procedure1

b.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals of the connectors are not deformed or damaged.


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

3.CHECK WIRE HARNESS (SHORT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK WIRE HARNESS (SHORT)
a.
C431634C04
0.833,2.167 1.177,2.396 0.344,0.229 1.427,2.698 1.74,2.313 true 2.313,2.698 1.948,2.313 true 1.625,0.865 1.625,0.615 false 0.563,0.854 0.833,1.063 0.271,0.208 10 false *1 2.698,0.854 3,1.146 0.302,0.292 10 false *2 1.552,0.438 1.813,0.604 0.26,0.167 10 false *3 0.667,1.771 1,2 0.333,0.229 10 false *a 2.229,0.854 2.385,1.063 0.156,0.208 10 false A 1.875,0.854 2.021,1.063 0.146,0.208 10 false B 1.281,0.854 1.427,1.063 0.146,0.208 10 false C 0.927,0.854 1.083,1.031 0.156,0.177 10 false D 0.875,2.208 1.167,2.385 0.292,0.177 10 false A42 2.229,2.729 2.635,2.917 0.406,0.188 10 false +SR 1.281,2.729 1.75,2.979 0.469,0.25 10 false -SR
*1 Front Airbag Sensor RH
*2 Airbag Sensor Assembly
*3 Wire Harness
*a Front view of wire harness connector
(to Front Airbag Sensor RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-2 (+SR) - A42-1 (-SR) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK WIRE HARNESS (SHORT TO GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK WIRE HARNESS (SHORT TO GROUND)
a.
C431634C04
0.833,2.167 1.177,2.396 0.344,0.229 1.427,2.698 1.74,2.313 true 2.313,2.698 1.948,2.313 true 1.625,0.865 1.625,0.615 false 0.563,0.854 0.833,1.063 0.271,0.208 10 false *1 2.698,0.854 3,1.146 0.302,0.292 10 false *2 1.552,0.438 1.813,0.604 0.26,0.167 10 false *3 0.667,1.771 1,2 0.333,0.229 10 false *a 2.229,0.854 2.385,1.063 0.156,0.208 10 false A 1.875,0.854 2.021,1.063 0.146,0.208 10 false B 1.281,0.854 1.427,1.063 0.146,0.208 10 false C 0.927,0.854 1.083,1.031 0.156,0.177 10 false D 0.875,2.208 1.167,2.385 0.292,0.177 10 false A42 2.229,2.729 2.635,2.917 0.406,0.188 10 false +SR 1.281,2.729 1.75,2.979 0.469,0.25 10 false -SR
*1 Front Airbag Sensor RH
*2 Airbag Sensor Assembly
*3 Wire Harness
*a Front view of wire harness connector
(to Front Airbag Sensor RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-2 (+SR) - Body ground Always 1 MΩ or higher
A42-1 (-SR) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK WIRE HARNESS (OPEN)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK WIRE HARNESS (OPEN)

Pre-procedure1

a.
C422853C02
0.854,0.833 1.219,1.073 0.365,0.24 0.719,3.729 1.073,3.969 0.354,0.24 1.677,1.813 1.677,1.688 false 1.25,1.667 1.615,1.313 true 2.083,1.667 1.729,1.302 true 1.229,4.25 1.521,3.844 true 2.052,4.25 1.75,3.844 true 1.667,3 1.667,2.74 false 0.396,2.583 0.667,2.896 0.271,0.313 10 false *1 2.729,2.583 3.083,2.896 0.354,0.313 10 false *2 1.615,1.802 1.917,1.958 0.302,0.156 10 false *4 0.667,0.188 1.021,0.5 0.354,0.313 10 false *b 0.667,3.417 0.917,3.667 0.25,0.25 10 false *a 2.365,2.583 2.51,2.813 0.146,0.229 10 false A 1.99,2.583 2.167,2.813 0.177,0.229 10 false B 1.135,2.583 1.323,2.813 0.188,0.229 10 false C 0.781,2.583 1.01,2.813 0.229,0.229 10 false D 0.906,0.854 1.219,1.052 0.313,0.198 10 false H14 2.01,1.667 2.417,1.875 0.406,0.208 10 false +SR 1.083,1.667 1.458,1.875 0.375,0.208 10 false -SR 0.771,3.75 1.083,3.938 0.313,0.188 10 false A42 1.083,4.25 1.417,4.49 0.333,0.24 10 false -SR 1.938,4.25 2.333,4.49 0.396,0.24 10 false +SR 1.604,3.01 2,3.219 0.396,0.208 10 false *3
*1 Front Airbag Sensor RH
*2 Airbag Sensor Assembly
*3 Wire Harness
*4 Service Wire
*a Front view of wire harness connector
(to Front Airbag Sensor RH)
*b Front view of wire harness connector
(to Airbag Sensor Assembly)


Using a service wire, connect terminals 29 (+SR) and 28 (-SR) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-2 (+SR) - A42-1 (-SR) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

c.

Disconnect the service wire from connector B.



OK

6.CHECK WIRE HARNESS (SHORT TO B+)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK WIRE HARNESS (SHORT TO B+)

Pre-procedure1

a.

Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the ignition switch to ON.


Procedure1

c.
C431634C04
0.833,2.167 1.177,2.396 0.344,0.229 1.427,2.698 1.74,2.313 true 2.313,2.698 1.948,2.313 true 1.625,0.865 1.625,0.615 false 0.563,0.854 0.833,1.063 0.271,0.208 10 false *1 2.698,0.854 3,1.146 0.302,0.292 10 false *2 1.552,0.438 1.813,0.604 0.26,0.167 10 false *3 0.667,1.771 1,2 0.333,0.229 10 false *a 2.229,0.854 2.385,1.063 0.156,0.208 10 false A 1.875,0.854 2.021,1.063 0.146,0.208 10 false B 1.281,0.854 1.427,1.063 0.146,0.208 10 false C 0.927,0.854 1.083,1.031 0.156,0.177 10 false D 0.875,2.208 1.167,2.385 0.292,0.177 10 false A42 2.229,2.729 2.635,2.917 0.406,0.188 10 false +SR 1.281,2.729 1.75,2.979 0.469,0.25 10 false -SR
*1 Front Airbag Sensor RH
*2 Airbag Sensor Assembly
*3 Wire Harness
*a Front view of wire harness connector
(to Front Airbag Sensor RH)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A42-2 (+SR) - Body ground Ignition switch ON Below 1 V
A42-1 (-SR) - Body ground Ignition switch ON Below 1 V


Result:
Proceed to
OK
NG



Post-procedure1

d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.




OK

7.CHECK FRONT AIRBAG SENSOR RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK FRONT AIRBAG SENSOR RH
a.
C422833C02
2.094,1 2.219,1.188 0.125,0.188 10 false A 1.938,1 2.083,1.271 0.146,0.271 10 false B 1.083,1.01 1.219,1.198 0.135,0.188 10 false C 0.927,1.01 1.042,1.229 0.115,0.219 10 false D 0.563,1.021 0.833,1.271 0.271,0.25 10 false *1 2.542,1.031 2.906,1.292 0.365,0.26 10 false *2
*1 Front Airbag Sensor LH
*2 Airbag Sensor Assembly


Connect the connector to the airbag sensor assembly.


b.

Interchange the front airbag sensor RH with LH and connect the connectors.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

f.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

8.CHECK FRONT AIRBAG SENSOR RH
8.CHECK FRONT AIRBAG SENSOR RH

Pre-procedure1

a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

b.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444
HINT:

Codes other than DTCs B009083 and B009583 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
B009583 is output A
B009083 is output B
B009083 and B009583 are not output C


Post-procedure1

c.

Turn the ignition switch off.


d.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



e.

Return the front airbag sensor RH and LH to their original positions and connect the connectors.



A

B

C