Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2020.09
RM36W0E _58 Vehicle Interior _088020 SUPPLEMENTAL RESTRAINT SYSTEMS _0420309 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B009887  Right Side Restraints Sensor 3 Missing Message  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Test Mode / Check Mode
B009887 Right Side Restraints Sensor 3 Missing Message
·

The airbag sensor assembly detects a line short in the side collision sensor RH circuit (bus 1) for 2 seconds

·

The airbag sensor assembly detects a short to ground in the side collision sensor RH circuit (bus 1) for 2 seconds

·

The airbag sensor assembly detects a short to B+ in the side collision sensor RH circuit (bus 1) for 2 seconds

·

The airbag sensor assembly detects an open in the side collision sensor RH circuit (bus 1) for 2 seconds

·

No. 2 side airbag sensor RH malfunction

·

Side airbag pressure sensor RH malfunction

·

Airbag sensor assembly malfunction


·

Harness or connector

·

No. 2 side airbag sensor RH

·

Side airbag pressure sensor RH

·

Airbag sensor assembly


Comes on Does not apply to test/check mode

WIRING DIAGRAM

C430311E02
4.833,1.99 6.823,2.417 1.99,0.427 10 false Airbag Sensor Assembly 4.833,1.823 5.667,2 0.833,0.177 10 false O24 5.354,0.948 5.979,1.271 0.625,0.323 10 false Interface 1.813,2.042 2.438,2.365 0.625,0.323 10 false Interface 5.083,3.229 5.688,3.604 0.604,0.375 10 false Interface 0.875,2.521 1.5,2.885 0.625,0.365 10 false Element 6.01,3.229 6.583,3.573 0.573,0.344 10 false Element 4.792,0.51 5.5,0.823 0.708,0.313 10 false BBR+ 4.792,1.177 6.458,1.542 1.667,0.365 10 false BBR- 4.552,0.51 5.135,0.875 0.583,0.365 10 false 25 4.552,1.177 6.219,1.542 1.667,0.365 10 false 26 2.531,0.5 4.198,0.865 1.667,0.365 10 false BCR+ 3.01,0.5 3.385,0.74 0.375,0.24 10 false 4 2.563,1.177 3.083,1.49 0.521,0.313 10 false BCR- 3.01,1.167 3.344,1.417 0.333,0.25 10 false 3 2.542,2.781 4.208,3.146 1.667,0.365 10 false BDR+ 3,2.771 3.208,3.01 0.208,0.24 10 false 1 2.552,3.458 4.219,3.823 1.667,0.365 10 false BDR- 3,3.458 3.24,3.74 0.24,0.281 10 false 2 4.344,2.781 6.01,3.146 1.667,0.365 10 false 2 4.344,3.458 4.656,3.74 0.313,0.281 10 false 1 4.521,2.771 5.135,3.063 0.615,0.292 10 false BDR+ 4.531,3.458 5.01,3.667 0.479,0.208 10 false BDR- 0.75,4.104 1.667,4.313 0.917,0.208 10 false O4 0.75,4.281 3.333,4.615 2.583,0.333 10 false No. 2 Side Airbag Sensor RH 4.5,4.104 5.583,4.313 1.083,0.208 10 false K1 4.5,4.281 6.917,4.667 2.417,0.385 10 false Side Airbag Pressure Sensor RH

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting the cable from the negative (-) auxiliary battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the cable to the auxiliary battery terminal, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




PROCEDURE

1.CHECK CONNECTION OF CONNECTORS

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



Procedure1

c.

Check that the connectors are properly connected to the airbag sensor assembly, side airbag pressure sensor RH and No. 2 side airbag sensor RH.

OK:

The connectors are properly connected.


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

2.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

2.CHECK CONNECTORS

Pre-procedure1

a.
C422861C02
1.708,0.99 1.708,0.656 false 0.49,0.958 0.719,1.188 0.229,0.229 10 false *1 2.771,0.958 3.083,1.229 0.313,0.271 10 false *2 1.646,0.479 1.969,0.656 0.323,0.177 10 false *3
*1 Side Airbag Pressure Sensor RH
*2 No. 2 Side Airbag Sensor RH
*3 Wire Harness


C422860C02
1.521,0.438 1.521,0.802 false 2.635,1.083 2.938,1.521 0.302,0.438 10 false *2 0.385,0.771 0.667,0.979 0.281,0.208 10 false *1 1.448,0.25 1.75,0.417 0.302,0.167 10 false *3
*1 No. 2 Side Airbag Sensor RH
*2 Airbag Sensor Assembly
*3 Wire Harness


Disconnect the connectors from the airbag sensor assembly, side airbag pressure sensor RH and No. 2 side airbag sensor RH.


Procedure1

b.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals of the connectors are not deformed or damaged.


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

3.CHECK WIRE HARNESS (SIDE AIRBAG PRESSURE SENSOR RH - NO. 2 SIDE AIRBAG SENSOR RH (SHORT))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK WIRE HARNESS (SIDE AIRBAG PRESSURE SENSOR RH - NO. 2 SIDE AIRBAG SENSOR RH (SHORT))
a.
C422842C04
0.646,2.198 1.052,2.448 0.406,0.25 1.708,0.979 1.708,0.729 false 1.25,2.75 1.667,2.333 true 2.167,2.75 1.781,2.333 true 0.479,0.583 0.833,0.906 0.354,0.323 10 false *1 2.75,0.573 3.083,0.917 0.333,0.344 10 false *2 1.635,1 1.875,1.25 0.24,0.25 10 false *3 0.667,1.75 0.917,2 0.25,0.25 10 false *a 1.063,2.792 1.542,3.042 0.479,0.25 10 false BDR+ 0.76,2.24 1.021,2.438 0.26,0.198 10 false O4 2.396,0.583 2.573,0.75 0.177,0.167 10 false A 2.094,0.583 2.26,0.75 0.167,0.167 10 false B 1.24,0.583 1.427,0.75 0.188,0.167 10 false C 0.938,0.583 1.073,0.75 0.135,0.167 10 false D 2.115,2.792 2.563,3.021 0.448,0.229 10 false BDR-
*1 Side Airbag Pressure Sensor RH
*2 No. 2 Side Airbag Sensor RH
*3 Wire Harness
*a Front view of wire harness connector
(to No. 2 Side Airbag Sensor RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O4-1 (BDR+) - O4-2 (BDR-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK WIRE HARNESS (SIDE AIRBAG PRESSURE SENSOR RH - NO. 2 SIDE AIRBAG SENSOR RH (SHORT TO GROUND))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK WIRE HARNESS (SIDE AIRBAG PRESSURE SENSOR RH - NO. 2 SIDE AIRBAG SENSOR RH (SHORT TO GROUND))
a.
C422842C04
0.646,2.198 1.052,2.448 0.406,0.25 1.708,0.979 1.708,0.729 false 1.25,2.75 1.667,2.333 true 2.167,2.75 1.781,2.333 true 0.479,0.583 0.833,0.906 0.354,0.323 10 false *1 2.75,0.573 3.083,0.917 0.333,0.344 10 false *2 1.635,1 1.875,1.25 0.24,0.25 10 false *3 0.667,1.75 0.917,2 0.25,0.25 10 false *a 1.063,2.792 1.542,3.042 0.479,0.25 10 false BDR+ 0.76,2.24 1.021,2.438 0.26,0.198 10 false O4 2.396,0.583 2.573,0.75 0.177,0.167 10 false A 2.094,0.583 2.26,0.75 0.167,0.167 10 false B 1.24,0.583 1.427,0.75 0.188,0.167 10 false C 0.938,0.583 1.073,0.75 0.135,0.167 10 false D 2.115,2.792 2.563,3.021 0.448,0.229 10 false BDR-
*1 Side Airbag Pressure Sensor RH
*2 No. 2 Side Airbag Sensor RH
*3 Wire Harness
*a Front view of wire harness connector
(to No. 2 Side Airbag Sensor RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O4-1 (BDR+) - Body ground Always 1 MΩ or higher
O4-2 (BDR-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK WIRE HARNESS (SIDE AIRBAG PRESSURE SENSOR RH - NO. 2 SIDE AIRBAG SENSOR RH (OPEN))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK WIRE HARNESS (SIDE AIRBAG PRESSURE SENSOR RH - NO. 2 SIDE AIRBAG SENSOR RH (OPEN))

Pre-procedure1

a.
C430310C04
0.823,0.625 1.177,0.865 0.354,0.24 0.708,3.615 1.094,3.865 0.385,0.25 1.25,4.167 1.646,3.76 true 2.198,4.167 1.802,3.76 true 1.844,1.344 1.844,1.177 false 1.24,1.177 1.719,0.74 true 2.344,1.177 1.948,0.74 true 1.719,2.771 1.719,2.469 false 0.552,2.323 0.854,2.583 0.302,0.26 10 false *1 2.719,2.323 3.208,2.792 0.49,0.469 10 false *2 1.792,1.344 2.094,1.542 0.302,0.198 10 false *4 0.656,3.177 1.094,3.656 0.438,0.479 10 false *a 0.635,0.177 0.99,0.396 0.354,0.219 10 false *b 2.385,2.323 2.552,2.573 0.167,0.25 10 false A 2.083,2.323 2.26,2.573 0.177,0.25 10 false B 1.219,2.323 1.365,2.531 0.146,0.208 10 false C 0.917,2.323 1.042,2.563 0.125,0.24 10 false D 2.24,1.188 2.781,1.458 0.542,0.271 10 false BDR+ 1.104,1.188 1.552,1.406 0.448,0.219 10 false BDR- 1.083,4.188 1.583,4.438 0.5,0.25 10 false BDR+ 2.083,4.188 2.552,4.438 0.469,0.25 10 false BDR- 0.813,3.656 1.063,3.854 0.25,0.198 10 false O4 0.917,0.656 1.177,0.885 0.26,0.229 10 false K1 1.667,2.771 1.969,2.979 0.302,0.208 10 false *3
*1 Side Airbag Pressure Sensor RH
*2 No. 2 Side Airbag Sensor RH
*3 Wire Harness
*4 Service Wire
*a Front view of wire harness connector
(to No. 2 Side Airbag Sensor RH)
*b Front view of wire harness connector
(to Side Airbag Pressure Sensor RH)


Using a service wire, connect terminals 2 (BDR+) and 1 (BDR-) of connector C.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O4-1 (BDR+) - O4-2 (BDR-) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

c.

Disconnect the service wire from connector C.



OK

6.CHECK WIRE HARNESS (SIDE AIRBAG PRESSURE SENSOR RH - NO. 2 SIDE AIRBAG SENSOR RH (SHORT TO B+))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK WIRE HARNESS (SIDE AIRBAG PRESSURE SENSOR RH - NO. 2 SIDE AIRBAG SENSOR RH (SHORT TO B+))

Pre-procedure1

a.

Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the ignition switch to ON.


Procedure1

c.
C422842C04
0.646,2.198 1.052,2.448 0.406,0.25 1.708,0.979 1.708,0.729 false 1.25,2.75 1.667,2.333 true 2.167,2.75 1.781,2.333 true 0.479,0.583 0.833,0.906 0.354,0.323 10 false *1 2.75,0.573 3.083,0.917 0.333,0.344 10 false *2 1.635,1 1.875,1.25 0.24,0.25 10 false *3 0.667,1.75 0.917,2 0.25,0.25 10 false *a 1.063,2.792 1.542,3.042 0.479,0.25 10 false BDR+ 0.76,2.24 1.021,2.438 0.26,0.198 10 false O4 2.396,0.583 2.573,0.75 0.177,0.167 10 false A 2.094,0.583 2.26,0.75 0.167,0.167 10 false B 1.24,0.583 1.427,0.75 0.188,0.167 10 false C 0.938,0.583 1.073,0.75 0.135,0.167 10 false D 2.115,2.792 2.563,3.021 0.448,0.229 10 false BDR-
*1 Side Airbag Pressure Sensor RH
*2 No. 2 Side Airbag Sensor RH
*3 Wire Harness
*a Front view of wire harness connector
(to No. 2 Side Airbag Sensor RH)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
O4-1 (BDR+) - Body ground Ignition switch ON Below 1 V
O4-2 (BDR-) - Body ground Ignition switch ON Below 1 V


Result:
Proceed to
OK
NG



Post-procedure1

d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.




OK

7.CHECK WIRE HARNESS (NO. 2 SIDE AIRBAG SENSOR RH - AIRBAG SENSOR ASSEMBLY (SHORT))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK WIRE HARNESS (NO. 2 SIDE AIRBAG SENSOR RH - AIRBAG SENSOR ASSEMBLY (SHORT))
a.
C431488C04
0.646,2.198 1.052,2.448 0.406,0.25 1.604,0.552 1.604,0.302 false 1.479,2.75 1.896,2.333 true 2.448,2.75 2.063,2.333 true 0.552,0.552 0.74,0.802 0.188,0.25 10 false *1 2.708,0.854 3.042,1.198 0.333,0.344 10 false *2 1.542,0.135 1.781,0.313 0.24,0.177 10 false *3 0.667,1.781 0.917,2.031 0.25,0.25 10 false *a 1.271,2.792 1.698,3.083 0.427,0.292 10 false BCR- 0.76,2.25 1.031,2.427 0.271,0.177 10 false O4 2.229,0.552 2.354,0.719 0.125,0.167 10 false A 1.885,0.552 2.021,0.719 0.135,0.167 10 false B 1.292,0.552 1.427,0.729 0.135,0.177 10 false C 0.938,0.552 1.073,0.719 0.135,0.167 10 false D 2.354,2.792 2.781,3.083 0.427,0.292 10 false BCR+
*1 No. 2 Side Airbag Sensor RH
*2 Airbag Sensor Assembly
*3 Wire Harness
*a Front view of wire harness connector
(to No. 2 Side Airbag Sensor RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O4-4 (BCR+) - O4-3 (BCR-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK WIRE HARNESS (NO. 2 SIDE AIRBAG SENSOR RH - AIRBAG SENSOR ASSEMBLY (SHORT TO GROUND))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK WIRE HARNESS (NO. 2 SIDE AIRBAG SENSOR RH - AIRBAG SENSOR ASSEMBLY (SHORT TO GROUND))
a.
C431488C04
0.646,2.198 1.052,2.448 0.406,0.25 1.604,0.552 1.604,0.302 false 1.479,2.75 1.896,2.333 true 2.448,2.75 2.063,2.333 true 0.552,0.552 0.74,0.802 0.188,0.25 10 false *1 2.708,0.854 3.042,1.198 0.333,0.344 10 false *2 1.542,0.135 1.781,0.313 0.24,0.177 10 false *3 0.667,1.781 0.917,2.031 0.25,0.25 10 false *a 1.271,2.792 1.698,3.083 0.427,0.292 10 false BCR- 0.76,2.25 1.031,2.427 0.271,0.177 10 false O4 2.229,0.552 2.354,0.719 0.125,0.167 10 false A 1.885,0.552 2.021,0.719 0.135,0.167 10 false B 1.292,0.552 1.427,0.729 0.135,0.177 10 false C 0.938,0.552 1.073,0.719 0.135,0.167 10 false D 2.354,2.792 2.781,3.083 0.427,0.292 10 false BCR+
*1 No. 2 Side Airbag Sensor RH
*2 Airbag Sensor Assembly
*3 Wire Harness
*a Front view of wire harness connector
(to No. 2 Side Airbag Sensor RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O4-4 (BCR+) - Body ground Always 1 MΩ or higher
O4-3 (BCR-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK WIRE HARNESS (NO. 2 SIDE AIRBAG SENSOR RH - AIRBAG SENSOR ASSEMBLY (OPEN))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK WIRE HARNESS (NO. 2 SIDE AIRBAG SENSOR RH - AIRBAG SENSOR ASSEMBLY (OPEN))

Pre-procedure1

a.
C422855C02
0.792,0.813 1.188,1.063 0.396,0.25 0.844,3.75 1.25,4 0.406,0.25 1.146,1.719 1.51,1.292 true 1.99,1.719 1.635,1.292 true 1.583,1.802 1.583,1.677 false 1.698,4.281 1.917,3.885 true 2.302,4.281 2.063,3.885 true 1.667,2.74 1.667,2.521 false 0.604,2.375 0.792,2.573 0.188,0.198 10 false *1 2.521,2.646 2.833,2.927 0.313,0.281 10 false *2 1.604,2.76 1.833,2.979 0.229,0.219 10 false *3 1.521,1.802 1.771,1.969 0.25,0.167 10 false *4 0.656,0.177 1.156,0.677 0.5,0.5 10 false *b 0.719,3.438 1.083,3.667 0.365,0.229 10 false *a 2.188,2.375 2.333,2.573 0.146,0.198 10 false A 1.885,2.375 2.083,2.573 0.198,0.198 10 false B 1.292,2.375 1.5,2.573 0.208,0.198 10 false C 0.979,2.375 1.167,2.573 0.188,0.198 10 false D 0.969,1.729 1.438,2 0.469,0.271 10 false BBR+ 0.938,3.781 1.25,3.979 0.313,0.198 10 false O4 1.917,1.729 2.417,1.917 0.5,0.188 10 false BBR- 0.865,0.844 1.198,1.052 0.333,0.208 10 false O24 2.198,4.281 2.708,4.531 0.51,0.25 10 false BCR+ 1.531,4.281 2.042,4.531 0.51,0.25 10 false BCR-
*1 No. 2 Side Airbag Sensor RH
*2 Airbag Sensor Assembly
*3 Wire Harness
*4 Service Wire
*a Front view of wire harness connector
(to No. 2 Side Airbag Sensor RH)
*b Front view of wire harness connector
(to Airbag Sensor Assembly)


Using a service wire, connect terminals 25 (BBR+) and 26 (BBR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O4-4 (BCR+) - O4-3 (BCR-) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

c.

Disconnect the service wire from connector B.



OK

10.CHECK WIRE HARNESS (NO. 2 SIDE AIRBAG SENSOR RH - AIRBAG SENSOR ASSEMBLY (SHORT TO B+))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK WIRE HARNESS (NO. 2 SIDE AIRBAG SENSOR RH - AIRBAG SENSOR ASSEMBLY (SHORT TO B+))

Pre-procedure1

a.

Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the ignition switch to ON.


Procedure1

c.
C431488C04
0.646,2.198 1.052,2.448 0.406,0.25 1.604,0.552 1.604,0.302 false 1.479,2.75 1.896,2.333 true 2.448,2.75 2.063,2.333 true 0.552,0.552 0.74,0.802 0.188,0.25 10 false *1 2.708,0.854 3.042,1.198 0.333,0.344 10 false *2 1.542,0.135 1.781,0.313 0.24,0.177 10 false *3 0.667,1.781 0.917,2.031 0.25,0.25 10 false *a 1.271,2.792 1.698,3.083 0.427,0.292 10 false BCR- 0.76,2.25 1.031,2.427 0.271,0.177 10 false O4 2.229,0.552 2.354,0.719 0.125,0.167 10 false A 1.885,0.552 2.021,0.719 0.135,0.167 10 false B 1.292,0.552 1.427,0.729 0.135,0.177 10 false C 0.938,0.552 1.073,0.719 0.135,0.167 10 false D 2.354,2.792 2.781,3.083 0.427,0.292 10 false BCR+
*1 No. 2 Side Airbag Sensor RH
*2 Airbag Sensor Assembly
*3 Wire Harness
*a Front view of wire harness connector
(to No. 2 Side Airbag Sensor RH)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
O4-4 (BCR+) - Body ground Ignition switch ON Below 1 V
O4-3 (BCR-) - Body ground Ignition switch ON Below 1 V


Result:
Proceed to
OK
NG



Post-procedure1

d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.




OK

11.CHECK SIDE AIRBAG PRESSURE SENSOR RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK SIDE AIRBAG PRESSURE SENSOR RH
a.

Connect the connectors to the No. 2 side airbag sensor RH and airbag sensor assembly.


b.
B529883C13
0.906,1.021 1.156,1.229 0.25,0.208 10 false *1 2.354,1 2.594,1.208 0.24,0.208 10 false *2 2.063,1.021 2.188,1.229 0.125,0.208 10 false A 1.906,1.021 2.031,1.25 0.125,0.229 10 false B 1.438,1.021 1.563,1.24 0.125,0.219 10 false C 1.281,1.021 1.417,1.24 0.135,0.219 10 false D
*1 Side Airbag Pressure Sensor LH
*2 No. 2 Side Airbag Sensor RH


Interchange the side airbag pressure sensor RH with LH and connect the connectors.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

f.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

12.CHECK SIDE AIRBAG PRESSURE SENSOR RH
12.CHECK SIDE AIRBAG PRESSURE SENSOR RH

Pre-procedure1

a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

b.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444
HINT:

Codes other than DTCs B009387 and B009887 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
B009887 is output A
B009387 is output B
B009387 and B009887 are not output C


Post-procedure1

c.

Turn the ignition switch off.


d.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



e.

Return the side airbag pressure sensor RH and LH to their original positions and connect the connectors.



A

13.CHECK NO. 2 SIDE AIRBAG SENSOR RH

B

C

13.CHECK NO. 2 SIDE AIRBAG SENSOR RH
a.
C422835C02
0.719,0.792 1.073,1.219 0.354,0.427 10 false *1 1.094,0.792 1.24,1.135 0.146,0.344 10 false D 1.25,0.792 1.427,1.125 0.177,0.333 10 false C 1.719,0.792 1.865,1.042 0.146,0.25 10 false B 1.875,0.792 2.052,1.052 0.177,0.26 10 false A 2.323,1.115 2.688,1.406 0.365,0.292 10 false *2
*1 No. 2 Side Airbag Sensor LH
*2 Airbag Sensor Assembly


Interchange the No. 2 side airbag sensor RH with LH and connect the connectors.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

e.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

14.CHECK NO. 2 SIDE AIRBAG SENSOR RH
14.CHECK NO. 2 SIDE AIRBAG SENSOR RH

Pre-procedure1

a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

b.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444
HINT:

Codes other than DTCs B009387 and B009887 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
B009887 is output A
B009387 is output B
B009387 and B009887 are not output C


Post-procedure1

c.

Turn the ignition switch off.


d.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



e.

Return the No. 2 side airbag sensor RH and LH to their original positions and connect the connectors.



A

B

C