Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2020.09
RM36W0E _58 Vehicle Interior _088020 SUPPLEMENTAL RESTRAINT SYSTEMS _0420309 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B18D013  Right Side 1st Seat Far Side Squib (Right Side 1st Seat Center Airbag) Circuit Open  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Test Mode / Check Mode
B18D013 Right Side 1st Seat Far Side Squib (Right Side 1st Seat Center Airbag) Circuit Open
·

The airbag sensor assembly detects an open in the right side 1st seat far side squib circuit for 2 seconds

·

Front seat center airbag assembly RH malfunction

·

Airbag sensor assembly malfunction


·

Harness or connector

·

Front seat center airbag assembly RH

·

Airbag sensor assembly


Comes on Applies to check mode

WIRING DIAGRAM

B502460E85
4.896,3.083 6.906,3.552 2.01,0.469 10 false Airbag Sensor Assembly 4.885,2.917 5.948,3.146 1.063,0.229 10 false H14*1, O24*2 4.26,1.313 4.917,1.583 0.656,0.271 10 false 1*1, 17*2 4.271,1.896 4.917,2.208 0.646,0.313 10 false 2*1, 18*2 4.958,1.333 5.417,1.542 0.458,0.208 10 false FFR+ 4.958,1.896 5.344,2.115 0.385,0.219 10 false FFR- 0.5,2.406 1.51,2.615 1.01,0.208 10 false O111 0.51,2.573 3.208,3.427 2.698,0.854 10 false Front Seat Center Airbag Assembly RH 2.094,1.875 2.896,2.521 0.802,0.646 10 false 1 2.094,1.323 2.896,1.969 0.802,0.646 10 false 2 1.625,1.333 2.031,1.531 0.406,0.198 10 false FFR+ 1.625,1.896 2.031,2.104 0.406,0.208 10 false FFR- 0.354,3.385 1.365,3.594 1.01,0.208 10 false *1: for RHD 1.406,3.375 2.417,3.583 1.01,0.208 10 false *2: for LHD

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting the cable from the negative (-) auxiliary battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the cable to the auxiliary battery terminal, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




HINT:
·

To perform the simulation method, select Check Mode with the GTS.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE

·

Perform the simulation method while checking the Data List.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DATA LIST / ACTIVE TEST



PROCEDURE

1.CHECK CURRENT DTC

Pre-procedure1

a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

b.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444
Result:
Result Proceed to
Current B18D013 is output A
History B18D013 is output B



Post-procedure1

c.

None



A

2.CHECK CONNECTION OF CONNECTORS

B

USE SIMULATION METHOD TO CHECK

2.CHECK CONNECTION OF CONNECTORS

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



Procedure1

c.

Check that the connectors are properly connected to the front seat center airbag assembly RH and airbag sensor assembly.

OK:

The connectors are properly connected.


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

3.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

3.CHECK CONNECTORS

Pre-procedure1

a.
C422865C01
0.531,1.646 0.531,1.271 false 1.365,1.656 1.365,1.281 false 0.531,3.667 0.531,3.292 false 1.375,3.677 1.375,3.302 false 0.094,0.083 0.469,0.323 0.375,0.24 12 false *A 0.073,2.438 0.448,2.677 0.375,0.24 12 false *B 2.438,1.125 2.75,1.281 0.313,0.156 10 false *2 1.313,1.667 1.625,1.823 0.313,0.156 10 false *3 2.448,3.448 2.76,3.604 0.313,0.156 10 false *2 0.458,1.646 0.771,1.802 0.313,0.156 10 false *1 0.469,3.667 0.781,3.823 0.313,0.156 10 false *1 1.333,3.688 1.646,3.844 0.313,0.156 10 false *3
*A for RHD
*B for LHD
*1 Front Seat Center Airbag Assembly RH
*2 Airbag Sensor Assembly
*3 Wire Harness


Disconnect the connectors from the front seat center airbag assembly RH and airbag sensor assembly.


Procedure1

b.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals of the connectors are not deformed or damaged.



c.

Check that the short springs of the activation prevention mechanisms of the wire harness connector are not deformed or damaged.

OK:

The short springs are not deformed or damaged.


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

4.CHECK FRONT SEAT CENTER AIRBAG ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK FRONT SEAT CENTER AIRBAG ASSEMBLY RH
a.

Connect the connector to the airbag sensor assembly.

C422866C01
0.656,1.833 1.073,2.167 0.417,0.333 4.219,1.833 4.635,2.167 0.417,0.333 0.885,0.979 0.885,0.708 false 4.458,0.771 4.458,0.448 false 5.208,0.771 5.208,0.448 false 1.635,0.979 1.635,0.708 false 2.25,2 2.417,2 false 5.833,2 6,2 false 0.052,0.063 0.49,0.302 0.438,0.24 12 false *A 3.552,0.031 3.906,0.271 0.354,0.24 12 false *B 0.813,0.979 1.125,1.135 0.313,0.156 10 false *1 2.385,0.563 2.698,0.719 0.313,0.156 10 false *2 1.573,1 1.885,1.156 0.313,0.156 10 false *3 0.698,1.354 1.01,1.51 0.313,0.156 10 false *a 4.26,1.313 4.573,1.469 0.313,0.156 10 false *a 5.969,0.542 6.281,0.698 0.313,0.156 10 false *2 5.156,0.802 5.469,0.958 0.313,0.156 10 false *3 4.406,0.792 4.719,0.948 0.313,0.156 10 false *1 0.698,1.906 1.313,2.104 0.615,0.198 10 false O111 4.26,1.906 4.875,2.104 0.615,0.198 10 false O111 2.479,1.906 3.094,2.104 0.615,0.198 10 false SST 6.063,1.906 6.677,2.104 0.615,0.198 10 false SST 2.031,0.552 2.188,0.75 0.156,0.198 10 false A 1.906,0.552 2.063,0.75 0.156,0.198 10 false B 1.292,0.563 1.448,0.76 0.156,0.198 10 false C 0.979,0.563 1.135,0.76 0.156,0.198 10 false D 4.552,0.302 4.708,0.5 0.156,0.198 10 false D 4.865,0.302 5.021,0.5 0.156,0.198 10 false C 5.479,0.302 5.635,0.5 0.156,0.198 10 false B 5.604,0.292 5.76,0.49 0.156,0.198 10 false A
*A for RHD *B for LHD
*1 Front Seat Center Airbag Assembly RH *2 Airbag Sensor Assembly
*3 Wire Harness - -
*a Front view of wire harness connector
(to Front Seat Center Airbag Assembly RH)
- -



b.

Connect the black wire side of SST (resistance 2.1 Ω) to connector C.

CAUTION:

Never connect a tester to the front seat center airbag assembly RH for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting it.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

f.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

5.CHECK FRONT SEAT CENTER AIRBAG ASSEMBLY RH
5.CHECK FRONT SEAT CENTER AIRBAG ASSEMBLY RH

Pre-procedure1

a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

b.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444
HINT:

Codes other than DTC B18D013 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
B18D013 is not output A
B18D013 is output B


Post-procedure1

c.

Turn the ignition switch off.


d.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



e.

Disconnect SST from connector C.



A

B

6.CHECK WIRE HARNESS (OPEN)
6.CHECK WIRE HARNESS (OPEN)

Pre-procedure1

a.

Disconnect the connector from the airbag sensor assembly.

C422867C01
0.604,1.802 1.083,2.115 0.479,0.313 4.25,1.833 4.729,2.146 0.479,0.313 0.813,1.052 0.813,0.844 false 1.51,1.052 1.51,0.844 false 4.438,0.802 4.438,0.594 false 5.104,0.792 5.104,0.583 false 1.115,2.313 1.417,2 true 4.75,2.313 5.052,2 true 2,2.323 1.74,1.99 true 5.625,2.333 5.365,2 true 0.052,0.063 0.406,0.313 0.354,0.25 12 false *A 3.438,0.083 3.781,0.313 0.344,0.229 12 false *B 0.74,1.073 1.052,1.229 0.313,0.156 10 false *1 2.354,0.708 2.667,0.865 0.313,0.156 10 false *2 1.458,1.063 1.771,1.219 0.313,0.156 10 false *3 0.646,1.417 0.958,1.656 0.313,0.24 10 false *a 5.969,0.719 6.281,0.875 0.313,0.156 10 false *2 4.25,1.427 4.563,1.667 0.313,0.24 10 false *a 5.042,0.802 5.354,0.958 0.313,0.156 10 false *3 4.375,0.823 4.688,0.979 0.313,0.156 10 false *1 0.667,1.865 1.281,2.063 0.615,0.198 10 false O111 4.313,1.885 4.927,2.083 0.615,0.198 10 false O111 0.958,2.323 1.573,2.521 0.615,0.198 10 false FFR- 1.885,2.323 2.5,2.521 0.615,0.198 10 false FFR+ 5.51,2.333 6.125,2.531 0.615,0.198 10 false FFR+ 4.625,2.323 5.24,2.521 0.615,0.198 10 false FFR- 1.979,0.688 2.135,0.885 0.156,0.198 10 false A 1.688,0.688 1.844,0.885 0.156,0.198 10 false B 1.208,0.688 1.365,0.885 0.156,0.198 10 false C 0.917,0.688 1.073,0.885 0.156,0.198 10 false D 5.594,0.438 5.75,0.635 0.156,0.198 10 false A 5.302,0.438 5.458,0.635 0.156,0.198 10 false B 4.823,0.438 4.979,0.635 0.156,0.198 10 false C 4.531,0.438 4.688,0.635 0.156,0.198 10 false D
*A for RHD *B for LHD
*1 Front Seat Center Airbag Assembly RH *2 Airbag Sensor Assembly
*3 Wire Harness - -
*a Front view of wire harness connector
(to Front Seat Center Airbag Assembly RH)
- -



Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O111-2 (FFR+) - O111-1 (FFR-) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

7.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CLEAR DTC
a.
C422868C01
0.938,1.552 0.938,1.271 false 0.938,3.573 0.938,3.292 false 0.063,0.073 0.531,0.375 0.469,0.302 12 false *A 0.083,2.375 0.656,2.927 0.573,0.552 12 false *B 0.875,1.573 1.188,1.729 0.313,0.156 10 false *1 2.448,1.135 2.76,1.292 0.313,0.156 10 false *2 0.885,3.573 1.198,3.729 0.313,0.156 10 false *1 2.479,3.49 2.792,3.646 0.313,0.156 10 false *2 2.021,1.115 2.177,1.313 0.156,0.198 10 false A 1.865,1.115 2.021,1.313 0.156,0.198 10 false B 1.208,1.115 1.365,1.313 0.156,0.198 10 false C 1.063,1.115 1.219,1.313 0.156,0.198 10 false D 2.01,3.135 2.167,3.333 0.156,0.198 10 false A 1.865,3.135 2.021,3.333 0.156,0.198 10 false B 1.208,3.135 1.365,3.333 0.156,0.198 10 false C 1.063,3.135 1.219,3.333 0.156,0.198 10 false D
*A for RHD
*B for LHD
*1 Front Seat Center Airbag Assembly RH
*2 Airbag Sensor Assembly


Connect the connectors to the front seat center airbag assembly RH and airbag sensor assembly.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

e.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

8.CHECK DTC
8.CHECK DTC

Pre-procedure1

a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

b.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444
HINT:

Codes other than DTC B18D013 may be output at this time, but they are not related to this check.


Result:
Result Proceed to
B18D013 is not output A
B18D013 is output B



Post-procedure1

c.

None



A

USE SIMULATION METHOD TO CHECK

B