81260A
1.INSPECT MAP LIGHT ASSEMBLY (for TMC Made)
Check the map light.
| *a | Component without harness connected
(Map Light Assembly) |
Apply auxiliary battery voltage to the map light assembly and check that the map light comes on.
| Auxiliary battery Connection | Switch Condition | Specified Condition |
|---|---|---|
| V7-1 (+B1) - Auxiliary battery positive (+)
V7-4 (GND) - Auxiliary battery negative (-) |
Map light switch LH on | Map light LH comes on |
| V7-1 (+B1) - Auxiliary battery positive (+)
V7-4 (GND) - Auxiliary battery negative (-) |
Map light switch LH off | Map light LH does not come on |
| V7-1 (+B1) - Auxiliary battery positive (+)
V7-4 (GND) - Auxiliary battery negative (-) |
Map light switch RH on | Map light RH comes on |
| V7-1 (+B1) - Auxiliary battery positive (+)
V7-4 (GND) - Auxiliary battery negative (-) |
Map light switch RH off | Map light RH does not come on |
| V7-1 (+B1) - Auxiliary battery positive (+)
V7-4 (GND) - Auxiliary battery negative (-) |
Map light switch off and door switch on | Map light comes on |
| V7-1 (+B1) - Auxiliary battery positive (+)
V7-4 (GND) - Auxiliary battery negative (-) |
Map light switch off and door switch off | Map light does not come on |
If the result is not as specified, replace the map light assembly.
Check the door switch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| V7-2 (DOOR) - V7-9 (RLMP) | Door switch on | Below 1 Ω |
| V7-2 (DOOR) - V7-9 (RLMP) | Door switch off | 10 kΩ or higher |
If the result is not as specified, replace the map light assembly.
81260A
2.INSPECT MAP LIGHT ASSEMBLY (for TMMF Made)
Check the map light.
| *a | Component without harness connected
(Map Light Assembly) |
Apply auxiliary battery voltage to the map light assembly and check that the map light comes on.
| Auxiliary battery Connection | Switch Condition | Specified Condition |
|---|---|---|
| V6-1 (+B1) - Auxiliary battery positive (+)
V6-8 (GND) - Auxiliary battery negative (-) |
Map light switch LH on | Map light LH comes on |
| V6-1 (+B1) - Auxiliary battery positive (+)
V6-8 (GND) - Auxiliary battery negative (-) |
Map light switch LH off | Map light LH does not come on |
| V6-1 (+B1) - Auxiliary battery positive (+)
V6-8 (GND) - Auxiliary battery negative (-) |
Map light switch RH on | Map light RH comes on |
| V6-1 (+B1) - Auxiliary battery positive (+)
V6-8 (GND) - Auxiliary battery negative (-) |
Map light switch RH off | Map light RH does not come on |
| V6-1 (+B1) - Auxiliary battery positive (+)
V6-8 (GND) - Auxiliary battery negative (-) |
Map light switch off and door switch on | Map light comes on |
| V6-1 (+B1) - Auxiliary battery positive (+)
V6-8 (GND) - Auxiliary battery negative (-) |
Map light switch off and door switch off | Map light does not come on |
If the result is not as specified, replace the map light assembly.
Check the door switch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| V6-7 (DOOR) - V6-6 (RLMP) | Door switch on | Below 1 Ω |
| V6-7 (DOOR) - V6-6 (RLMP) | Door switch off | 10 kΩ or higher |
If the result is not as specified, replace the map light assembly.