RM36W0E
_V1
General
_087262
SPECIFICATIONS
_0426673
CLUTCH
F
SPECIFICATIONS CLUTCH SERVICE DATA
Clutch Pedal (for LHD)
| Clutch pedal height from floor panel
|
-
|
154.8 to 174.8 mm (6.09 to 6.88 in.)
|
| Clutch pedal free play
|
Reference
|
3 to 15 mm (0.118 to 0.591 in.)
|
| Clutch pedal stroke end position to release point
|
Standard distance
|
25 mm (0.984 in.) or more
|
| Clutch pedal stroke at 200 N (20 kgf, 45.0 lbf)
|
Reference
|
141 to 151 mm (5.55 to 5.94 in.)
|
Clutch Pedal (for RHD)
| Clutch pedal height from floor panel
|
-
|
158.1 to 178.1 mm (6.22 to 7.01 in.)
|
| Clutch pedal free play
|
Reference
|
3 to 15 mm (0.118 to 0.591 in.)
|
| Clutch pedal stroke end position to release point
|
Standard distance
|
25 mm (0.984 in.) or more
|
| Clutch pedal stroke at 200 N (20 kgf, 45.0 lbf)
|
Reference
|
141 to 151 mm (5.55 to 5.94 in.)
|
Clutch Stroke Sensor (for LHD)
| GTS display
|
Condition
|
Specified condition
|
| Clutch stroke sensor voltage
|
Clutch pedal fully released
|
0.96 to 1.04 V
|
| Not depressed → Fully depressed (Clutch pedal should be operated slowly)
|
Value changes progressively (Only increase)
|
Clutch Stroke Sensor (for RHD)
| GTS display
|
Condition
|
Specified condition
|
| Clutch stroke sensor voltage
|
Clutch pedal fully released
|
0.96 to 1.04 V
|
| Not depressed → Fully depressed (Clutch pedal should be operated slowly)
|
Value changes progressively (Only increase)
|
Clutch Unit (for C551)
| Clutch disc assembly rivet head depth
|
Minimum rivet head depth
|
0.3 mm (0.0118 in.)
|
| Clutch disc assembly runout
|
Maximum runout
|
0.8 mm (0.0315 in.)
|
| Clutch cover assembly diaphragm spring wear
|
Maximum depth
|
0.5 mm (0.0197 in.)
|
| Maximum width
|
6.0 mm (0.236 in.)
|
| Flywheel sub-assembly runout
|
Maximum runout
|
0.1 mm (0.00394 in.)
|
| Clutch cover assembly diaphragm spring tip alignment
|
Maximum non-alignment
|
0.5 mm (0.0197 in.)
|
Clutch Unit (for EC6A)
| Clutch disc assembly rivet head depth
|
Minimum rivet head depth
|
0.3 mm (0.0118 in.)
|
| Clutch disc assembly runout
|
Maximum runout
|
0.8 mm (0.0315 in.)
|
| Clutch cover assembly diaphragm spring wear
|
Maximum depth
|
0.5 mm (0.0197 in.)
|
| Maximum width
|
6.0 mm (0.236 in.)
|
| Flywheel sub-assembly runout
|
Maximum runout
|
0.1 mm (0.00394 in.)
|
| Clutch cover assembly diaphragm spring tip alignment
|
Maximum non-alignment
|
0.5 mm (0.0197 in.)
|
Clutch Unit (for EA67F)
| Clutch disc assembly rivet head depth
|
Minimum rivet head depth
|
0.3 mm (0.0118 in.)
|
| Clutch disc assembly runout
|
Maximum runout
|
0.8 mm (0.0315 in.)
|
| Clutch cover assembly diaphragm spring wear
|
Maximum depth
|
0.5 mm (0.0197 in.)
|
| Maximum width
|
6.0 mm (0.236 in.)
|
| Flywheel sub-assembly runout
|
Maximum runout
|
0.1 mm (0.00394 in.)
|
| Clutch cover assembly diaphragm spring tip alignment
|
Maximum non-alignment
|
0.5 mm (0.0197 in.)
|
Clutch Pedal Switch
| Clutch start switch assembly
|
| Tester connection
|
Condition
|
Specified condition
|
| A64-1 - A64-2
|
On (Pushed in)
|
Below 1 Ω
|
| A64-1 - A64-2
|
Off (Released)
|
10 kΩ or higher
|
| Clutch switch assembly (except G16E-GTS)
|
| Tester connection
|
Condition
|
Specified condition
|
| A65-1 - A65-2
|
On (Pushed in)
|
Below 1 Ω
|
| A65-1 - A65-2
|
Off (Released)
|
10 kΩ or higher
|
Brake Fluid
|
|
| -
|
SAE J1703 or FMVSS No. 116 DOT3
|
| -
|
SAE J1704 or FMVSS No. 116 DOT4
|
| -
|
"TOYOTA GENUINE BRAKE FLUID DOT4, CLASS6"*, FMVSS No.116 DOT4 or SAE J1704LV*
|