Home › Vehicle Interior › SEAT › SEAT HEATER SWITCH › from 2020.09
RM36W0E _58 Vehicle Interior _088297 SEAT _0436949 SEAT HEATER SWITCH G

SEAT  SEAT HEATER SWITCH  INSPECTION  


PROCEDURE

Hide 84751G 1.INSPECT SEAT HEATER SWITCH (for LH Side)

a.
B602104C01
1.469,2.583 1.969,2.833 0.5,0.25 2.5,4.25 2.271,3.823 true 2.167,4.25 2.052,3.833 true 1.896,4.25 1.823,3.823 true 1.542,4.24 1.583,3.823 true 1.25,4.25 1.385,3.813 true 0.917,4.25 1.188,3.833 true 0.583,2.417 0.896,2.615 0.313,0.198 10 false *a 0.833,4.25 1.146,4.448 0.313,0.198 10 false IG 1.844,4.25 2,4.448 0.156,0.198 10 false E 2.469,4.25 2.781,4.448 0.313,0.198 10 false HI 1.469,4.25 1.781,4.448 0.313,0.198 10 false LO 1.115,4.25 1.729,4.448 0.615,0.198 10 false ILL+ 2.083,4.25 2.698,4.448 0.615,0.198 10 false ILL- 1.552,2.635 2.167,2.833 0.615,0.198 10 false H135
*a Component without harness connected (Seat Heater Switch)


for HI/LOW Switch Type:

i.

Check the resistance.

1.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition

If the result is not as specified, replace the seat heater switch.

H135-6 (IG) - H135-3 (E)
H135-6 (IG) - H135-1 (HI)
H135-4 (LO) - H135-3 (E)
"HI" switch off 10 kΩ or higher
H135-6 (IG) - H135-3 (E)
H135-6 (IG) - H135-1 (HI)
H135-4 (LO) - H135-3 (E)
"HI" switch on Below 1 Ω
H135-6 (IG) - H135-3 (E)
H135-6 (IG) - H135-4 (LO)
"LO" switch off 10 kΩ or higher
H135-6 (IG) - H135-3 (E)
H135-6 (IG) - H135-4 (LO)
"LO" switch on Below 1 Ω



ii.

Check the indicator illuminates.

1.

Apply battery voltage to the seat heater switch and check that the seat heater switch indicator illuminates.

OK:
Measurement Connection Switch Condition Specified Condition

If the result is not as specified, replace the seat heater switch.

Battery positive (+) → H135-6 (IG)
Battery negative (-) → H135-3 (E)
"HI" switch on illuminates
Battery positive (+) → H135-6 (IG)
Battery negative (-) → H135-3 (E)
"LO" switch on illuminates



iii.

Check the illuminates.

1.

Apply battery voltage to the seat heater switch and check that the seat heater switch illuminates.

OK:
Measurement Connection Switch Condition Specified Condition

If the result is not as specified, replace the seat heater switch.

Battery positive (+) → H135-5 (ILL+)
Battery negative (-) → H135-2 (ILL-)
Always illuminates




b.
B480111C05
1.458,2.5 1.958,2.75 0.5,0.25 0.729,4.177 1.167,3.802 true 1.156,4.177 1.396,3.802 true 1.604,4.177 1.604,3.813 true 2.104,4.156 2.052,3.802 true 2.573,4.156 2.292,3.802 true 0.667,2.583 0.927,2.844 0.26,0.26 10 false *a 1.594,2.563 2.052,2.76 0.458,0.198 10 false H52 0.583,4.208 1.198,4.406 0.615,0.198 10 false ILL+ 1.083,4.198 1.698,4.396 0.615,0.198 10 false IG 1.583,4.208 2.198,4.406 0.615,0.198 10 false E 2.063,4.188 2.677,4.385 0.615,0.198 10 false LO 2.5,4.188 3.115,4.385 0.615,0.198 10 false ILL-
*a Component without harness connected (Seat Heater Switch)


for ON/OFF Switch Type:

i.

Check the resistance.

1.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition

If the result is not as specified, replace the seat heater switch.

H52-5 (IG) - H52-2 (LO) Switch off 10 kΩ or higher
H52-5 (IG) - H52-2 (LO) Switch on Below 1 Ω



ii.

Check the indicator illuminates.

1.

Apply battery voltage to the seat heater switch and check that the seat heater switch indicator illuminates.

OK:
Measurement Connection Switch Condition Specified Condition

If the result is not as specified, replace the seat heater switch.

Battery positive (+) → H52-5 (IG)
Battery negative (-) → H52-4 (E)
Switch on illuminates



iii.

Check the illuminates.

1.

Apply battery voltage to the seat heater switch and check that the seat heater switch illuminates.

OK:
Measurement Connection Switch Condition Specified Condition

If the result is not as specified, replace the seat heater switch.

Battery positive (+) → H52-6 (ILL+)
Battery negative (-) → H52-1 (ILL-)
Always illuminates




Hide 84751F 2.INSPECT SEAT HEATER SWITCH (for RH Side)

a.
B602104C02
1.438,2.583 1.938,2.833 0.5,0.25 2.5,4.25 2.271,3.823 true 2.167,4.25 2.052,3.833 true 1.896,4.25 1.823,3.823 true 1.542,4.24 1.583,3.823 true 1.25,4.25 1.385,3.813 true 0.917,4.25 1.188,3.833 true 0.583,2.417 0.896,2.615 0.313,0.198 10 false *a 0.833,4.25 1.146,4.448 0.313,0.198 10 false IG 1.844,4.25 2,4.448 0.156,0.198 10 false E 2.469,4.25 2.781,4.448 0.313,0.198 10 false HI 1.469,4.25 1.781,4.448 0.313,0.198 10 false LO 1.115,4.25 1.729,4.448 0.615,0.198 10 false ILL+ 2.083,4.25 2.698,4.448 0.615,0.198 10 false ILL- 1.51,2.625 2.125,2.823 0.615,0.198 10 false H134
*a Component without harness connected (Seat Heater Switch)


for HI/LOW Switch Type:

i.

Check the resistance.

1.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition

If the result is not as specified, replace the seat heater switch.

H134-6 (IG) - H134-3 (E)
H134-6 (IG) - H134-1 (HI)
H134-4 (LO) - H134-3 (E)
"HI" switch off 10 kΩ or higher
H134-6 (IG) - H134-3 (E)
H134-6 (IG) - H134-1 (HI)
H134-4 (LO) - H134-3 (E)
"HI" switch on Below 1 Ω
H134-6 (IG) - H134-3 (E)
H134-6 (IG) - H134-4 (LO)
"LO" switch off 10 kΩ or higher
H134-6 (IG) - H134-3 (E)
H134-6 (IG) - H134-4 (LO)
"LO" switch on Below 1 Ω



ii.

Check the indicator illuminates.

1.

Apply battery voltage to the seat heater switch and check that the seat heater switch indicator illuminates.

OK:
Measurement Connection Switch Condition Specified Condition

If the result is not as specified, replace the seat heater switch.

Battery positive (+) → H134-6 (IG)
Battery negative (-) → H134-3 (E)
"HI" switch on illuminates
Battery positive (+) → H134-6 (IG)
Battery negative (-) → H134-3 (E)
"LO" switch on illuminates



iii.

Check the illuminates.

1.

Apply battery voltage to the seat heater switch and check that the seat heater switch illuminates.

OK:
Measurement Connection Switch Condition Specified Condition

If the result is not as specified, replace the seat heater switch.

Battery positive (+) → H134-5 (ILL+)
Battery negative (-) → H134-2 (ILL-)
Always illuminates




b.
B480112C04
1.458,2.5 1.958,2.75 0.5,0.25 0.729,4.177 1.167,3.802 true 1.156,4.177 1.396,3.802 true 1.604,4.177 1.604,3.813 true 2.104,4.156 2.052,3.802 true 2.573,4.156 2.292,3.802 true 0.667,2.583 0.927,2.844 0.26,0.26 10 false *a 1.594,2.563 2.052,2.76 0.458,0.198 10 false H50 0.583,4.208 1.198,4.406 0.615,0.198 10 false ILL+ 1.083,4.198 1.698,4.396 0.615,0.198 10 false IG 1.583,4.208 2.198,4.406 0.615,0.198 10 false E 2.063,4.188 2.677,4.385 0.615,0.198 10 false LO 2.5,4.188 3.115,4.385 0.615,0.198 10 false ILL-
*a Component without harness connected (Seat Heater Switch)


for ON/OFF Switch Type:

i.

Check the resistance.

1.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition

If the result is not as specified, replace the seat heater switch.

H50-5 (IG) - H50-2 (LO) Switch off 10 kΩ or higher
H50-5 (IG) - H50-2 (LO) Switch on Below 1 Ω



ii.

Check the indicator illuminates.

1.

Apply battery voltage to the seat heater switch and check that the seat heater switch indicator illuminates.

OK:
Measurement Connection Switch Condition Specified Condition

If the result is not as specified, replace the seat heater switch.

Battery positive (+) → H50-5 (IG)
Battery negative (-) → H50-4 (E)
Switch on illuminates



iii.

Check the illuminates.

1.

Apply battery voltage to the seat heater switch and check that the seat heater switch illuminates.

OK:
Measurement Connection Switch Condition Specified Condition

If the result is not as specified, replace the seat heater switch.

Battery positive (+) → H50-6 (ILL+)
Battery negative (-) → H50-1 (ILL-)
Always illuminates