If there is a short in a speaker circuit, the radio and display receiver assembly detects it and stops output to the speakers.
Thus sound cannot be heard from the speakers even if there is no malfunction in the radio and display receiver assembly or speakers.
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| for 2 Speakers | A |
| for 4 Speakers | B |
| for 6 Speakers | C |
| for 8 Speakers | D |
A
B
C
D
Disconnect the H83 radio and display receiver assembly connector.
Disconnect the K2 and L2 front No. 1 speaker assembly connectors.
Disconnect the H130 and H129 wiring harness connector connectors.
Measure the resistance according to the value (s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H83-1 (FR+) - H130-3 (+) | Always | Below 1 Ω |
| H83-6 (FR-) - H130-1 (-) | Always | Below 1 Ω |
| H83-2 (FL+) - H129-3 (+) | Always | Below 1 Ω |
| H83-7 (FL-) - H129-1 (-) | Always | Below 1 Ω |
| H130-4 (TWR+) - K2-2 | Always | Below 1 Ω |
| H130-2 (TWR-) - K2-1 | Always | Below 1 Ω |
| H129-4 (TWL+) - L2-2 | Always | Below 1 Ω |
| H129-2 (TWL-) - L2-1 | Always | Below 1 Ω |
| H83-1 (FR+) or H130-3 (+) - Body ground | Always | 10 kΩ or higher |
| H83-6 (FR-) or H130-1 (-) - Body ground | Always | 10 kΩ or higher |
| H83-2 (FL+) or H129-3 (+) - Body ground | Always | 10 kΩ or higher |
| H83-7 (FL-) or H129-1 (-) - Body ground | Always | 10 kΩ or higher |
| H130-4 (TWR+) or K2-2 - Body ground | Always | 10 kΩ or higher |
| H130-2 (TWR-) or K2-1 - Body ground | Always | 10 kΩ or higher |
| H129-4 (TWL+) or L2-2 - Body ground | Always | 10 kΩ or higher |
| H129-2 (TWL-) or L2-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>PILLAR SPEAKER>INSPECTION
Malfunction disappears.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| w/o Active Noise Control System | A |
| w/ Active Noise Control System | B |
A
B
Enter the "System Check Mode" screen. Refer to Check Speaker in Operation Check.
Perform the operation check above and determine the speaker that is not operating.
| Not Operating Speaker | Proceed to |
|---|---|
| Front No. 1 speaker assembly | A |
| Rear speaker assembly | B |
If sound cannot be heard from any speaker, inspect all of them.
A
B
Disconnect the H83 radio and display receiver assembly connector.
Disconnect the K2 and L2 front No. 1 speaker assembly connectors.
Disconnect the H130 and H129 wiring harness connector connectors.
Measure the resistance according to the value (s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H83-1 (FR+) - H130-3 (+) | Always | Below 1 Ω |
| H83-6 (FR-) - H130-1 (-) | Always | Below 1 Ω |
| H83-2 (FL+) - H129-3 (+) | Always | Below 1 Ω |
| H83-7 (FL-) - H129-1 (-) | Always | Below 1 Ω |
| H130-4 (TWR+) - K2-2 | Always | Below 1 Ω |
| H130-2 (TWR-) - K2-1 | Always | Below 1 Ω |
| H129-4 (TWL+) - L2-2 | Always | Below 1 Ω |
| H129-2 (TWL-) - L2-1 | Always | Below 1 Ω |
| H83-1 (FR+) or H130-3 (+) - Body ground | Always | 10 kΩ or higher |
| H83-6 (FR-) or H130-1 (-) - Body ground | Always | 10 kΩ or higher |
| H83-2 (FL+) or H129-3 (+) - Body ground | Always | 10 kΩ or higher |
| H83-7 (FL-) or H129-1 (-) - Body ground | Always | 10 kΩ or higher |
| H130-4 (TWR+) or K2-2 - Body ground | Always | 10 kΩ or higher |
| H130-2 (TWR-) or K2-1 - Body ground | Always | 10 kΩ or higher |
| H129-4 (TWL+) or L2-2 - Body ground | Always | 10 kΩ or higher |
| H129-2 (TWL-) or L2-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>PILLAR SPEAKER>INSPECTION
Malfunction disappears.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H83 radio and display receiver assembly connector.
Disconnect the M2 and N2 rear speaker assembly connectors.
Measure the resistance according to the value (s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H83-4 (RR+) - M2-2 | Always | Below 1 Ω |
| H83-9 (RR-) - M2-1 | Always | Below 1 Ω |
| H83-3 (RL+) - N2-2 | Always | Below 1 Ω |
| H83-8 (RL-) - N2-1 | Always | Below 1 Ω |
| H83-4 (RR+) or M2-2 - Body ground | Always | 10 kΩ or higher |
| H83-9 (RR-) or M2-1 - Body ground | Always | 10 kΩ or higher |
| H83-3 (RL+) or N2-2 - Body ground | Always | 10 kΩ or higher |
| H83-8 (RL-) or N2-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>INSPECTION
Malfunction disappears.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Enter the "System Check Mode" screen. Refer to Check Speaker in Operation Check.
Perform the operation check above and determine the speaker that is not operating.
| Not Operating Speaker | Proceed to |
|---|---|
| Front No. 1 speaker assembly | A |
| Rear speaker assembly | B |
If sound cannot be heard from any speaker, inspect all of them.
A
B
Disconnect the O131 stereo component equalizer assembly connector.
Disconnect the K2 and L2 front No. 1 speaker assembly connectors.
Measure the resistance according to the value (s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O131-12 (FR+) - K2-2 | Always | Below 1 Ω |
| O131-27 (FR-) - K2-1 | Always | Below 1 Ω |
| O131-13 (FL+) - L2-2 | Always | Below 1 Ω |
| O131-28 (FL-) - L2-1 | Always | Below 1 Ω |
| O131-12 (FR-) or K2-2 - Body ground | Always | 10 kΩ or higher |
| O131-27 (FR-) or K2-1 - Body ground | Always | 10 kΩ or higher |
| O131-12 (FR-) or K2-2 - Body ground | Always | 10 kΩ or higher |
| O131-27 (FR-) or K2-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>PILLAR SPEAKER>INSPECTION
Malfunction disappears.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the O131 stereo component equalizer assembly connector.
Disconnect the O114 and O115 rear speaker assembly connectors.
Measure the resistance according to the value (s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O131-10 (RR+) - O114-2 | Always | Below 1 Ω |
| O131-25 (RR-) - O114-1 | Always | Below 1 Ω |
| O131-11 (RL+) - O115-2 | Always | Below 1 Ω |
| O131-26 (RL-) - O115-1 | Always | Below 1 Ω |
| O131-10 (RR+) or O114-2 - Body ground | Always | 10 kΩ or higher |
| O131-25 (RR-) or O114-1 - Body ground | Always | 10 kΩ or higher |
| O131-11 (RL+) or O115-2 - Body ground | Always | 10 kΩ or higher |
| O131-26 (RL-) or O115-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>INSPECTION
Malfunction disappears.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| w/o Active Noise Control System | A |
| w/ Active Noise Control System | B |
A
B
Enter the "System Check Mode" screen. Refer to Check Speaker in Operation Check.
Perform the operation check above and determine the speaker that is not operating.
| Not Operating Speaker | Proceed to |
|---|---|
| Front No. 1 speaker assembly or front No. 2 speaker assembly | A |
| Rear speaker assembly | B |
If sound cannot be heard from any speaker, inspect all of them.
A
B
Disconnect the H83 radio and display receiver assembly connector.
Disconnect the K2 and L2 front No. 1 speaker assembly connectors.
Disconnect the H88 and H87 front No. 2 speaker assembly connectors.
Measure the resistance according to the value (s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H83-1 (FR+) - H88-3 (+) | Always | Below 1 Ω |
| H83-6 (FR-) - H88-1 (-) | Always | Below 1 Ω |
| H83-2 (FL+) - H87-3 (+) | Always | Below 1 Ω |
| H83-7 (FL-) - H87-1 (-) | Always | Below 1 Ω |
| H88-4 (TWR+) - K2-2 | Always | Below 1 Ω |
| H88-2 (TWR-) - K2-1 | Always | Below 1 Ω |
| H87-4 (TWL+) - L2-2 | Always | Below 1 Ω |
| H87-2 (TWL-) - L2-1 | Always | Below 1 Ω |
| H83-1 (FR+) or H88-3 (+) - Body ground | Always | 10 kΩ or higher |
| H83-6 (FR-) or H88-1 (-) - Body ground | Always | 10 kΩ or higher |
| H83-2 (FL+) or H87-3 (+) - Body ground | Always | 10 kΩ or higher |
| H83-7 (FL-) or H87-1 (-) - Body ground | Always | 10 kΩ or higher |
| H88-4 (TWR+) or K2-2 - Body ground | Always | 10 kΩ or higher |
| H88-2 (TWR-) or K2-1 - Body ground | Always | 10 kΩ or higher |
| H87-4 (TWL+) or L2-2 - Body ground | Always | 10 kΩ or higher |
| H87-2 (TWL-) or L2-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>PILLAR SPEAKER>INSPECTION
Malfunction disappears.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H83 radio and display receiver assembly connector.
Disconnect the M2 and N2 rear speaker assembly connectors.
Measure the resistance according to the value (s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H83-4 (RR+) - M2-2 | Always | Below 1 Ω |
| H83-9 (RR-) - M2-1 | Always | Below 1 Ω |
| H83-3 (RL+) - N2-2 | Always | Below 1 Ω |
| H83-8 (RL-) - N2-1 | Always | Below 1 Ω |
| H83-4 (RR+) or M2-2 - Body ground | Always | 10 kΩ or higher |
| H83-9 (RR-) or M2-1 - Body ground | Always | 10 kΩ or higher |
| H83-3 (RL+) or N2-2 - Body ground | Always | 10 kΩ or higher |
| H83-8 (RL-) or N2-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>INSPECTION
Malfunction disappears.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Enter the "System Check Mode" screen. Refer to Check Speaker in Operation Check.
Perform the operation check above and determine the speaker that is not operating.
| Not Operating Speaker | Proceed to |
|---|---|
| Front No. 1 speaker assembly or front No. 2 speaker assembly | A |
| Rear speaker assembly | B |
If sound cannot be heard from any speaker, inspect all of them.
A
B
Disconnect the O131 stereo component equalizer assembly connector.
Disconnect the K2 and L2 front No. 1 speaker assembly connectors.
Disconnect the H88 and H87 front No. 2 speaker assembly connectors.
Measure the resistance according to the value (s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O131-12 (FR+) - H88-3 (+) | Always | Below 1 Ω |
| O131-27 (FR-) - H88-1 (-) | Always | Below 1 Ω |
| O131-13 (FL+) - H87-3 (+) | Always | Below 1 Ω |
| O131-28 (FL-) - H87-1 (-) | Always | Below 1 Ω |
| H88-4 (TWR+) - K2-2 | Always | Below 1 Ω |
| H88-2 (TWR-) - K2-1 | Always | Below 1 Ω |
| H87-4 (TWL+) - L2-2 | Always | Below 1 Ω |
| H87-2 (TWL-) - L2-1 | Always | Below 1 Ω |
| O131-12 (FR+) or H88-3 (+) - Body ground | Always | 10 kΩ or higher |
| O131-27 (FR-) or H88-1 (-) - Body ground | Always | 10 kΩ or higher |
| O131-13 (FL+) or H87-3 (+) - Body ground | Always | 10 kΩ or higher |
| O131-28 (FL-) or H87-1 (-) - Body ground | Always | 10 kΩ or higher |
| H88-4 (TWR+) or K2-2 - Body ground | Always | 10 kΩ or higher |
| H88-2 (TWR-) or K2-1 - Body ground | Always | 10 kΩ or higher |
| H87-4 (TWL+) or L2-2 - Body ground | Always | 10 kΩ or higher |
| H87-2 (TWL-) or L2-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>PILLAR SPEAKER>INSPECTION
Malfunction disappears.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the O131 stereo component equalizer assembly connector.
Disconnect the O115 and O114 rear speaker assembly connectors.
Measure the resistance according to the value (s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O131-10 (RR+) - O115-2 | Always | Below 1 Ω |
| O131-25 (RR-) - O115-1 | Always | Below 1 Ω |
| O131-11 (RL+) - O114-2 | Always | Below 1 Ω |
| O131-26 (RL-) - O114-1 | Always | Below 1 Ω |
| O131-10 (RR+) or O115-2 - Body ground | Always | 10 kΩ or higher |
| O131-25 (RR-) or O115-1 - Body ground | Always | 10 kΩ or higher |
| O131-11 (RL+) or O114-2 - Body ground | Always | 10 kΩ or higher |
| O131-26 (RL-) or O114-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>INSPECTION
Malfunction disappears.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| except G16E-GTS | A |
| for G16E-GTS | B |
A
B
Enter the "System Check Mode" screen. Refer to Check Speaker in Operation Check.
Perform the operation check above and determine the speaker that is not operating.
| Not Operating Speaker | Proceed to |
|---|---|
| Front No. 1 speaker assembly | A |
| Front No. 2 speaker assembly | B |
| Front No. 4 speaker assembly | C |
| Rear speaker assembly | D |
If sound cannot be heard from any speaker, inspect all of them.
A
B
C
D
Disconnect the H136 stereo component amplifier assembly connector.
Disconnect the K2 and L2 front No. 1 speaker assembly connectors.
Measure the resistance according to the value (s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H136-10 (WFR+) - K2-2 | Always | Below 1 Ω |
| H136-25 (WFR-) - K2-1 | Always | Below 1 Ω |
| H136-8 (WFL+) - L2-2 | Always | Below 1 Ω |
| H136-23 (WFL-) - L2-1 | Always | Below 1 Ω |
| H136-10 (WFR+) or K2-2 - Body ground | Always | 10 kΩ or higher |
| H136-25 (WFR-) or K2-1 - Body ground | Always | 10 kΩ or higher |
| H136-8 (WFL+) or L2-2 - Body ground | Always | 10 kΩ or higher |
| H136-23 (WFL-) or L2-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>PILLAR SPEAKER>INSPECTION
Malfunction disappears.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H136 stereo component amplifier assembly connector.
Disconnect the H88 and H87 front No. 2 speaker assembly connectors.
Measure the resistance according to the value (s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H136-14 (TWR+) - H88-4 | Always | Below 1 Ω |
| H136-29 (TWR-) - H88-2 | Always | Below 1 Ω |
| H136-12 (TWL+) - H87-4 | Always | Below 1 Ω |
| H136-27 (TWL-) - H87-2 | Always | Below 1 Ω |
| H136-14 (TWR+) or H88-4 - Body ground | Always | 10 kΩ or higher |
| H136-29 (TWR-) or H88-2 - Body ground | Always | 10 kΩ or higher |
| H136-12 (TWL+) or H87-4 - Body ground | Always | 10 kΩ or higher |
| H136-27 (TWL-) or H87-2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>PILLAR SPEAKER>INSPECTION
Malfunction disappears.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H136 stereo component amplifier assembly connector.
Disconnect the H139 and H138 front No. 4 speaker assembly connectors.
Measure the resistance according to the value (s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H136-11 (FR+) - H139-2 | Always | Below 1 Ω |
| H136-26 (FR-) - H139-1 | Always | Below 1 Ω |
| H136-9 (FL+) - H138-2 | Always | Below 1 Ω |
| H136-24 (FL-) - H138-1 | Always | Below 1 Ω |
| H136-11 (FR+) or H139-2 - Body ground | Always | 10 kΩ or higher |
| H136-26 (FR-) or H139-1 - Body ground | Always | 10 kΩ or higher |
| H136-9 (FL+) or H138-2 - Body ground | Always | 10 kΩ or higher |
| H136-24 (FL-) or H138-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>INSPECTION
Malfunction disappears.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H136 stereo component amplifier assembly connector.
Disconnect the M2 and N2 rear speaker assembly connectors.
Measure the resistance according to the value (s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H136-15 (RR+) - M2-2 | Always | Below 1 Ω |
| H136-30 (RR-) - M2-1 | Always | Below 1 Ω |
| H136-13 (RL+) - N2-2 | Always | Below 1 Ω |
| H136-28 (RL-) - N2-1 | Always | Below 1 Ω |
| H136-15 (RR+) or M2-2 - Body ground | Always | 10 kΩ or higher |
| H136-30 (RR-) or M2-1 - Body ground | Always | 10 kΩ or higher |
| H136-13 (RL+) or N2-2 - Body ground | Always | 10 kΩ or higher |
| H136-28 (RL-) or N2-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>INSPECTION
Malfunction disappears.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Enter the "System Check Mode" screen. Refer to Check Speaker in Operation Check.
Perform the operation check above and determine the speaker that is not operating.
| Not Operating Speaker | Proceed to |
|---|---|
| Front No. 1 speaker assembly | A |
| Front No. 2 speaker assembly | B |
| Front No. 4 speaker assembly | C |
| Rear speaker assembly | D |
If sound cannot be heard from any speaker, inspect all of them.
A
B
C
D
Disconnect the O121 stereo component amplifier assembly connector.
Disconnect the K2 and L2 front No. 1 speaker assembly connectors.
Measure the resistance according to the value (s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O121-10 (WFR+) - K2-2 | Always | Below 1 Ω |
| O121-25 (WFR-) - K2-1 | Always | Below 1 Ω |
| O121-8 (WFL+) - L2-2 | Always | Below 1 Ω |
| O121-23 (WFL-) - L2-1 | Always | Below 1 Ω |
| O121-10 (WFR+) or K2-2 - Body ground | Always | 10 kΩ or higher |
| O121-25 (WFR-) or K2-1 - Body ground | Always | 10 kΩ or higher |
| O121-8 (WFL+) or L2-2 - Body ground | Always | 10 kΩ or higher |
| O121-23 (WFL-) or L2-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>PILLAR SPEAKER>INSPECTION
Malfunction disappears.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the O121 stereo component amplifier assembly connector.
Disconnect the H88 and H87 front No. 2 speaker assembly connectors.
Measure the resistance according to the value (s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O121-14 (TWR+) - H88-4 | Always | Below 1 Ω |
| O121-29 (TWR-) - H88-2 | Always | Below 1 Ω |
| O121-12 (TWL+) - H87-4 | Always | Below 1 Ω |
| O121-27 (TWL-) - H87-2 | Always | Below 1 Ω |
| O121-14 (TWR+) or H88-4 - Body ground | Always | 10 kΩ or higher |
| O121-29 (TWR-) or H88-2 - Body ground | Always | 10 kΩ or higher |
| O121-12 (TWL+) or H87-4 - Body ground | Always | 10 kΩ or higher |
| O121-27 (TWL-) or H87-2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>PILLAR SPEAKER>INSPECTION
Malfunction disappears.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the O121 stereo component amplifier assembly connector.
Disconnect the H139 and H138 front No. 4 speaker assembly connectors.
Measure the resistance according to the value (s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O121-11 (FR+) - H139-2 | Always | Below 1 Ω |
| O121-26 (FR-) - H139-1 | Always | Below 1 Ω |
| O121-9 (FL+) - H138-2 | Always | Below 1 Ω |
| O121-24 (FL-) - H138-1 | Always | Below 1 Ω |
| O121-11 (FR+) or H139-2 - Body ground | Always | 10 kΩ or higher |
| O121-26 (FR-) or H139-1 - Body ground | Always | 10 kΩ or higher |
| O121-9 (FL+) or H138-2 - Body ground | Always | 10 kΩ or higher |
| O121-24 (FL-) or H138-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>INSPECTION
Malfunction disappears.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the O121 stereo component amplifier assembly connector.
Disconnect the O115 and O114 rear speaker assembly connectors.
Measure the resistance according to the value (s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O121-15 (RR+) - O115-2 | Always | Below 1 Ω |
| O121-30 (RR-) - O115-1 | Always | Below 1 Ω |
| O121-13 (RL+) - O114-2 | Always | Below 1 Ω |
| O121-28 (RL-) - O114-1 | Always | Below 1 Ω |
| O121-15 (RR+) or O115-2 - Body ground | Always | 10 kΩ or higher |
| O121-30 (RR-) or O115-1 - Body ground | Always | 10 kΩ or higher |
| O121-13 (RL+) or O114-2 - Body ground | Always | 10 kΩ or higher |
| O121-28 (RL-) or O114-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>INSPECTION
Malfunction disappears.
| Proceed to |
|---|
| OK |
| NG |
OK
NG