TERMINALS OF ECU
| *a | Component without harness connected
(Skid Control ECU [Brake Actuator Assembly]) |
- | - |
| Terminal No. (Symbol) | Terminal Description |
|---|---|
| 1 (GND2) | Pump motor ground |
| 2 | - (Not used) |
| 3 | - (Not used) |
| 4 | - (Not used) |
| 5 (STP2) | Stop light switch assembly input |
| 6 | - (Not used) |
| 7 | - (Not used) |
| 8 | - (Not used) |
| 9 | - (Not used) |
| 10 (CANL) | CAN communication line L |
| 11 | - (Not used) |
| 12 (IGR) | ECU power supply input |
| 13 (BM) | Motor relay power supply |
| 14 (SP1) | Speed signal output for speedometer |
| 15 (RR-) | Rear wheel speed RH (-) signal input |
| 16 (RR+) | Rear wheel speed RH (+) power supply output |
| 17 (FL-) | Front wheel speed LH (-) signal input |
| 18 (FL+) | Front wheel speed LH (+) power supply output |
| 19 | - (Not used) |
| 20 | - (Not used) |
| 21 | - (Not used) |
| 22 (CANH) | CAN communication line H |
| 23 | - (Not used) |
| 24 | - (Not used) |
| 25 (GND1) | Skid control ECU (Brake actuator assembly) ground |
| 26 (STPO) | Stop light switch assembly output |
| 27 | - (Not used) |
| 28 (RL-) | Rear wheel speed LH (-) signal input |
| 29 (RL+) | Rear wheel speed LH (+) power supply output |
| 30 (FR-) | Front wheel speed RH (-) signal input |
| 31 (FR+) | Front wheel speed RH (+) power supply output |
| 32 | - (Not used) |
| 33 (CSW) | VSC OFF switch (Integration control and panel assembly) input |
| 34 | - (Not used) |
| 35 (STP) | Stop light switch assembly input |
| 36 (CA2H)* | CAN communication line H |
| 37 (CA2L)* | CAN communication line L |
| 38 (+BS) | Solenoid relay power supply |
*: for 3 Door
TERMINAL INSPECTION
Disconnect the A36 or A108 connector and measure the voltage or resistance on the wire harness side.
| *A | for 5 Door | *B | for 3 Door |
| *a | Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly]) |
- | - |
Voltage cannot be measured with the connector connected to the skid control ECU (brake actuator assembly) as the connector is watertight.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| A36-1 (GND2) - Body ground | Pump motor ground | Always | Below 1 Ω |
| A36-5 (STP2) - Body ground | Stop light switch assembly input | Brake pedal depressed → released | 8 to 14 V → Below 1.5 V |
| A36-12 (IGR) - Body ground | ECU power supply input | Ignition switch ON | 11 to 14 V |
| A36-13 (BM) - Body ground | Motor relay power supply | Always | 11 to 14 V |
| A36-14 (SP1) - Body ground | Speed signal output for speedometer | Ignition switch ON | 11 to 14 V |
| A36-25 (GND1) - Body ground | Skid control ECU (Brake actuator assembly) ground | Always | Below 1 Ω |
| A36-26 (STPO) - Body ground | Stop light switch assembly output | Ignition switch ON | 11 to 14 V |
| A36-33 (CSW) - Body ground | VSC OFF switch (Integration control and panel assembly) input | VSC OFF switch (integration control and panel assembly) pressed and held → released | Below 1 Ω → 10 kΩ or higher |
| A36-35 (STP) - Body ground | Stop light switch assembly input | Stop light switch assembly on → off
(Brake pedal depressed → released) |
8 to 14 V → Below 1.5 V |
| A36-38 (+BS) - Body ground | Solenoid relay power supply | Always | 11 to 14 V |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| A108-1 (GND2) - Body ground | Pump motor ground | Always | Below 1 Ω |
| A108-5 (STP2) - Body ground | Stop light switch assembly input | Brake pedal depressed → released | 8 to 14 V → Below 1.5 V |
| A108-12 (IGR) - Body ground | ECU power supply input | Ignition switch ON | 10.5 to 16 V |
| A108-13 (BM) - Body ground | Motor relay power supply | Always | 11 to 14 V |
| A108-14 (SP1) - Body ground | Speed signal output for speedometer | Ignition switch ON | 11 to 14 V |
| A108-25 (GND1) - Body ground | Skid control ECU (Brake actuator assembly) ground | Always | Below 1 Ω |
| A108-26 (STPO) - Body ground | Stop light switch assembly output | Ignition switch ON | 11 to 14 V |
| A108-33 (CSW) - Body ground | VSC OFF switch (Integration control and panel assembly) input | VSC OFF switch (integration control and panel assembly) pressed and held → released | Below 1 Ω → 10 kΩ or higher |
| A108-35 (STP) - Body ground | Stop light switch assembly input | Stop light switch assembly on → off
(Brake pedal depressed → released) |
8 to 14 V → Below 1.5 V |
| A108-38 (+BS) - Body ground | Solenoid relay power supply | Always | 11 to 14 V |