Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for HV Model) › from 2021.11
RM36W0E _57 Power Source / Network _088060 NETWORKING _0424238 CAN COMMUNICATION SYSTEM(for HV Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for HV Model)  Certification ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Certification ECU Communication Stop Mode Communication stop for "Certification (Smart)" is indicated on the "Communication Bus Check" screen of the GTS.
·

Certification ECU (smart key ECU assembly) branch line or connector

·

Power source circuit of certification ECU (smart key ECU assembly)

·

Certification ECU (smart key ECU assembly) ground circuit

·

Certification ECU (smart key ECU assembly)



WIRING DIAGRAM

C427543E03
0.302,1.646 3.208,1.844 2.906,0.198 10 false No. 3 Global CAN Junction Connector 0.313,1.49 0.688,1.688 0.375,0.198 10 false H114 5.302,4.052 5.677,4.25 0.375,0.198 10 false H46 5.302,4.219 6.823,4.688 1.521,0.469 10 false Certification ECU (Smart Key ECU Assembly) 1.698,2.604 3.521,2.885 1.823,0.281 10 false from Auxiliary Battery 4.219,2.781 4.74,2.948 0.521,0.167 10 false AM2 5.688,3.448 5.854,3.625 0.167,0.177 10 false E 5.656,2.615 5.917,2.792 0.26,0.177 10 false +B 5.667,1.167 6.063,1.344 0.396,0.177 10 false CANL 5.656,0.583 6.052,0.76 0.396,0.177 10 false CANH 5.396,2.51 5.604,2.698 0.208,0.188 10 false 6 5.354,3.333 5.563,3.521 0.208,0.188 10 false 29 5.417,1.052 5.625,1.24 0.208,0.188 10 false 2 5.406,0.448 5.615,0.635 0.208,0.188 10 false 1 1.74,0.479 1.948,0.667 0.208,0.188 10 false 4 1.698,1.031 1.906,1.219 0.208,0.188 10 false 15

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more.

Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>DIAGNOSIS SYSTEM

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H46 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H46-1 (CANH) - H46-2 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H46-29 (E) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) auxiliary battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H46-6 (+B) - Body ground Ignition switch off 11 to 14 V



Result:
Result
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)