Home › General › SPECIFICATIONS › P910 HYBRID TRANSMISSION / TRANSAXLE › from 2021.11
RM36W0E _V1 General _087262 SPECIFICATIONS _0422001 P910 HYBRID TRANSMISSION / TRANSAXLE F

SPECIFICATIONS  P910 HYBRID TRANSMISSION / TRANSAXLE  SERVICE DATA  


Hybrid Transaxle System
Maintenance mode engine idle speed Hybrid transaxle fluid temperature Hybrid transaxle fluid pressure
950 to 1050 rpm 20 to 50°C (68 to 122°F) 9.8 kPa (0.1 kgf/cm2, 1 psi) or more

Hybrid Transaxle Fluid

*: Using transmission fluid other than the above type may cause abnormal noise or vibration, or ultimately damage the transmission of your vehicle.

Hybrid transaxle fluid standard capacity (for Reference) Classification
2.6 liters (2.7 US qts, 2.3 Imp. qts) Toyota Genuine ATF WS

Hybrid Transaxle Oil Seal
Front drive shaft oil seal RH Standard depth -0.5 to 0.5 mm (-0.0197 to 0.0197 in.)
Front drive shaft oil seal LH Standard depth -0.5 to 0.5 mm (-0.0197 to 0.0197 in.)

Shift Lever (for TMC Made)
Shift lock control ECU (w/ Smart Entry and Start System)
Inspect wire harness:
Tester Connection Condition Specified Condition
H20-5(IG) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
H20-4(STP) - Body ground Ready ON, brake pedal depressed 11 to 14 V
Ready ON, brake pedal released Below 1 V
H20-1(E) - Body ground Always Below 1 Ω
Inspect shift lock solenoid:
A-1(SLS+) - A-2(SLS-) Always 112 Ω
A-4(P) - A-3(E2) Shift lever in P 10 kΩ or higher
Shift lever not in P Below 1 Ω
Shift lock control ECU (w/o Smart Entry and Start System)
Inspect wire harness:
Tester Connection Condition Specified Condition
H19-1(ACC) - Body ground Ignition switch ACC 11 to 14 V
Ignition switch off Below 1 V
H19-4(IG) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
H19-8(STP) - Body ground Ignition switch ON, brake pedal depressed 11 to 14 V
Ignition switch ON, brake pedal released Below 1 V
H19-7(E) - Body ground Always Below 1 Ω
Inspect key interlock solenoid operation signal:
Tester Connection Condition Specified Condition
H19-5(KLS+) - Body ground Ignition switch ACC and shift lever in P Below 1 V
Ignition switch ACC and shift lever not in P 11 to 14 V
Inspect shift lock solenoid:
Tester Connection Condition Specified Condition
A-4(P) - A-3(E2) Shift lever in P 10 kΩ or higher
Shift lever not in P Below 1 Ω
A-1(SLS+) - A-2(SLS-) Always 112 Ω

Shift Lever (for TMMF, TMMCZ Made)
Shift lock control ECU (w/ Smart Entry and Start System)
Inspect wire harness:
Tester Connection Condition Specified Condition
H20-5(IG) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
H20-4(STP) - Body ground Ready ON, brake pedal depressed 11 to 14 V
Ready ON, brake pedal released Below 1 V
H20-1(E) - Body ground Always Below 1 Ω
Inspect shift lock solenoid:
A-1(SLS+) - A-2(SLS-) Always 112 Ω
A-4(P) - A-3(E2) Shift lever in P 10 kΩ or higher
Shift lever not in P Below 1 Ω
Shift lock control ECU (w/o Smart Entry and Start System)
Inspect wire harness:
Tester Connection Condition Specified Condition
H19-1(ACC) - Body ground Ignition switch ACC 11 to 14 V
Ignition switch off Below 1 V
H19-4(IG) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
H19-8(STP) - Body ground Ignition switch ON, brake pedal depressed 11 to 14 V
Ignition switch ON, brake pedal released Below 1 V
H19-7(E) - Body ground Always Below 1 Ω
Inspect key interlock solenoid operation signal:
Tester Connection Condition Specified Condition
H19-5(KLS+) - Body ground Ignition switch ACC and shift lever in P Below 1 V
Ignition switch ACC and shift lever not in P 11 to 14 V
Inspect shift lock solenoid:
Tester Connection Condition Specified Condition
A-4(P) - A-3(E2) Shift lever in P 10 kΩ or higher
Shift lever not in P Below 1 Ω
A-1(SLS+) - A-2(SLS-) Always 112 Ω

Input Shaft Oil Seal
Input shaft type T oil seal Standard depth 1.0 to 1.8 mm (0.0394 to 0.0709 in.)

Combination Switch
Tester Connection Condition Specified Condition
H18-8(DRV) - H18-5(E) Switch pushed Below 1 Ω
H18-8(DRV) - H18-5(E) Switch not pushed 10 kΩ or higher
H18-4(ILL+) - H18-1(ILL-) H18-4(ILL+) - Auxiliary battery positive (+)
H18-1(ILL-) - Auxiliary battery negative (-)
The drive mode select switch (combination switch assembly) illumination illuminates.

Shift Lever Position Sensor
Tester Connection Condition Specified Condition
D46-7(+B) - D46-3(PR) Shift lever in P Below 1 Ω
D46-7(+B) - D46-4(PNB) Below 1 Ω
D46-7(+B) - D46-8(P) Below 1 Ω
D46-7(+B) - D46-1(DB1) Shift lever in P 10 kΩ or higher
D46-7(+B) - D46-2(N) 10 kΩ or higher
D46-7(+B) - D46-6(DB2) 10 kΩ or higher
D46-7(+B) - D46-9(R) 10 kΩ or higher
D46-7(+B) - D46-3(PR) Shift lever in R Below 1 Ω
D46-7(+B) - D46-9(R) Below 1 Ω
D46-7(+B) - D46-1(DB1) Shift lever in R 10 kΩ or higher
D46-7(+B) - D46-2(N) 10 kΩ or higher
D46-7(+B) - D46-4(PNB) 10 kΩ or higher
D46-7(+B) - D46-6(DB2) 10 kΩ or higher
D46-7(+B) - D46-8(P) 10 kΩ or higher
D46-7(+B) - D46-2(N) Shift lever in N Below 1 Ω
D46-7(+B) - D46-4(PNB) Below 1 Ω
D46-7(+B) - D46-1(DB1) Shift lever in N 10 kΩ or higher
D46-7(+B) - D46-3(PR) 10 kΩ or higher
D46-7(+B) - D46-6(DB2) 10 kΩ or higher
D46-7(+B) - D46-8(P) 10 kΩ or higher
D46-7(+B) - D46-9(R) 10 kΩ or higher
D46-7(+B) - D46-1(DB1) Shift lever in D Below 1 Ω
D46-7(+B) - D46-6(DB2) Below 1 Ω
D46-7(+B) - D46-2(N) Shift lever in D 10 kΩ or higher
D46-7(+B) - D46-3(PR) 10 kΩ or higher
D46-7(+B) - D46-4(PNB) 10 kΩ or higher
D46-7(+B) - D46-8(P) 10 kΩ or higher
D46-7(+B) - D46-9(R) 10 kΩ or higher
D46-7(+B) - D46-1(DB1) Shift lever in B Below 1 Ω
D46-7(+B) - D46-6(DB2) Below 1 Ω
D46-7(+B) - D46-2(N) Shift lever in B 10 kΩ or higher
D46-7(+B) - D46-3(PR) 10 kΩ or higher
D46-7(+B) - D46-4(PNB) 10 kΩ or higher
D46-7(+B) - D46-8(P) 10 kΩ or higher
D46-7(+B) - D46-9(R) 10 kΩ or higher