Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMMF, TMMCZ Made) › from 2021.11
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0494153 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMMF, TMMCZ Made) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMMF, TMMCZ Made)  C127A11  Electronic Brake Booster Input Stroke Sensor "A" Circuit Short to Ground  C127A15  Electronic Brake Booster Input Stroke Sensor "A" Circuit Short to Battery or Open  C127A16  Electronic Brake Booster Input Stroke Sensor "A" Circuit Voltage Below Threshold  C127A17  Electronic Brake Booster Input Stroke Sensor "A" Circuit Voltage Above Threshold  C127A23  Electronic Brake Booster Input Stroke Sensor "A" Signal Stuck Low  C127A24  Electronic Brake Booster Input Stroke Sensor "A" Signal Stuck High  C127A64  Electronic Brake Booster Input Stroke Sensor "A" Signal Plausibility Failure  C127A86  Electronic Brake Booster Input Stroke Sensor "A" Signal (some circuit quantity, reported via serial data) Invalid  C127A96  Electronic Brake Booster Input Stroke Sensor "A" Component Internal Failure  C127F1C  Electronic Brake Booster Input Stroke Sensor Supply Voltage Circuit Voltage Out of Range  C128A11  Electronic Brake Booster Input Stroke Sensor "B" Circuit Short to Ground  C128A15  Electronic Brake Booster Input Stroke Sensor "B" Circuit Short to Battery or Open  C128A64  Electronic Brake Booster Input Stroke Sensor "B" Signal Plausibility Failure  C128F64  Electronic Brake Booster Input Stroke Sensor "A" / "B" Signal Plausibility Failure  


DESCRIPTION

The relative displacement sensor sends the brake pedal stroke distance to the electric brake booster (brake booster with master cylinder assembly).

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
C127A11 Electronic Brake Booster Input Stroke Sensor "A" Circuit Short to Ground Open in relative displacement sensor (brake booster with master cylinder assembly) signal circuit for 0.1 seconds or more.
·

Wire harness or connector*

·

No. 2 engine room wire*

·

Electric brake booster (brake booster with master cylinder assembly)


Brake Booster
C127A15 Electronic Brake Booster Input Stroke Sensor "A" Circuit Short to Battery or Open Short in relative displacement sensor (brake booster with master cylinder assembly) signal circuit for 0.1 seconds or more.
·

Wire harness or connector*

·

No. 2 engine room wire*

·

Electric brake booster (brake booster with master cylinder assembly)


Brake Booster
C127A16 Electronic Brake Booster Input Stroke Sensor "A" Circuit Voltage Below Threshold Relative displacement sensor (brake booster with master cylinder assembly) output value is -3.9 mm or less for 0.2 seconds or more.
·

Wire harness or connector*

·

No. 2 engine room wire*

·

Electric brake booster (brake booster with master cylinder assembly)


Brake Booster
C127A17 Electronic Brake Booster Input Stroke Sensor "A" Circuit Voltage Above Threshold Relative displacement sensor (brake booster with master cylinder assembly) output value is 3.4 mm or more for 0.2 seconds or more.
·

Wire harness or connector*

·

No. 2 engine room wire*

·

Electric brake booster (brake booster with master cylinder assembly)


Brake Booster
C127A23 Electronic Brake Booster Input Stroke Sensor "A" Signal Stuck Low Relative displacement sensor (brake booster with master cylinder assembly) output value is less than 0.6 mm for 0.3 seconds or more.
·

Wire harness or connector*

·

No. 2 engine room wire*

·

Electric brake booster (brake booster with master cylinder assembly)


Brake Booster
C127A24 Electronic Brake Booster Input Stroke Sensor "A" Signal Stuck High
Any of the following conditions are met:
·

Relative displacement sensor (brake booster with master cylinder assembly) output value abnormality was detected in the previous cycle and the current cycle for 60 seconds or more.

·

Relative displacement sensor (brake booster with master cylinder assembly) output value was outside the operating range in the previous cycle and the current cycle for 300 seconds or more.

·

Relative displacement sensor (brake booster with master cylinder assembly) output value is 0.6 mm or more and within 1.5 mm for 60 seconds or more.


·

Wire harness or connector*

·

No. 2 engine room wire*

·

Electric brake booster (brake booster with master cylinder assembly)


Brake Booster
C127A64 Electronic Brake Booster Input Stroke Sensor "A" Signal Plausibility Failure Relative displacement sensor (brake booster with master cylinder assembly) output signal interrupted for 0.1 seconds or more.
·

Wire harness or connector*

·

No. 2 engine room wire*

·

Electric brake booster (brake booster with master cylinder assembly)


Brake Booster
C127A86 Electronic Brake Booster Input Stroke Sensor "A" Signal (some circuit quantity, reported via serial data) Invalid Relative displacement sensor (brake booster with master cylinder assembly) malfunction is detected for 1 second or more.
·

Wire harness or connector*

·

No. 2 engine room wire*

·

Electric brake booster (brake booster with master cylinder assembly)


Brake Booster
C127A96 Electronic Brake Booster Input Stroke Sensor "A" Component Internal Failure Relative displacement sensor (brake booster with master cylinder assembly) internal malfunction is detected for 0.1 seconds or more.
·

Wire harness or connector*

·

No. 2 engine room wire*

·

Electric brake booster (brake booster with master cylinder assembly)


Brake Booster
C127F1C Electronic Brake Booster Input Stroke Sensor Supply Voltage Circuit Voltage Out of Range Relative displacement sensor (brake booster with master cylinder assembly) power source voltage (VSK) is less than 4.8 V or more than 5.18 V for 0.08 seconds or more.
·

Wire harness or connector*

·

No. 2 engine room wire*

·

Electric brake booster (brake booster with master cylinder assembly)


Brake Booster
C128A11 Electronic Brake Booster Input Stroke Sensor "B" Circuit Short to Ground Open in relative displacement sensor (brake booster with master cylinder assembly) signal circuit for 0.2 seconds or more.
·

Wire harness or connector*

·

No. 2 engine room wire*

·

Electric brake booster (brake booster with master cylinder assembly)


Brake Booster
C128A15 Electronic Brake Booster Input Stroke Sensor "B" Circuit Short to Battery or Open Short in relative displacement sensor (brake booster with master cylinder assembly) signal circuit for 0.2 seconds or more.
·

Wire harness or connector*

·

No. 2 engine room wire*

·

Electric brake booster (brake booster with master cylinder assembly)


Brake Booster
C128A64 Electronic Brake Booster Input Stroke Sensor "B" Signal Plausibility Failure Relative displacement sensor (brake booster with master cylinder assembly) operation failure is detected for 0.2 seconds or more.
·

Wire harness or connector*

·

No. 2 engine room wire*

·

Electric brake booster (brake booster with master cylinder assembly)


Brake Booster
C128F64 Electronic Brake Booster Input Stroke Sensor "A" / "B" Signal Plausibility Failure Difference between change amounts of relative displacement sensor (brake booster with master cylinder assembly) output 1 (SKS1) and relative displacement sensor (brake booster with master cylinder assembly) output 2 (SKS2) is abnormally large for 0.2 seconds or more.
·

Wire harness or connector*

·

No. 2 engine room wire*

·

Electric brake booster (brake booster with master cylinder assembly)


Brake Booster

*: for RHD


WIRING DIAGRAM

C443939E02
0.635,3.073 3.01,3.49 2.375,0.417 10 false Electric Brake Booster (Brake Booster with Master Cylinder Assembly) 5.313,2.917 6.708,3.74 1.396,0.823 10 false Relative Displacement Sensor (Brake Master Cylinder with Motor Assembly) 3.594,2.896 5.448,3.313 1.854,0.417 10 false No. 2 Engine Room Wire 0.073,0.083 1.01,0.292 0.938,0.208 12 false for RHD: 3.625,2.458 4.167,2.698 0.542,0.24 10 false AR1 0.625,2.875 1.167,3.115 0.542,0.24 10 false A35 3.635,1.885 4.177,2.125 0.542,0.24 10 false AR1 3.635,1.24 4.177,1.479 0.542,0.24 10 false AR1 3.625,0.656 4.167,0.896 0.542,0.24 10 false AR1 5.021,0.646 5.563,0.885 0.542,0.24 10 false R2 5.031,1.25 5.573,1.49 0.542,0.24 10 false R2 5.042,2.458 5.583,2.698 0.542,0.24 10 false R2 5.031,1.875 5.573,2.115 0.542,0.24 10 false R2 5.094,2.24 5.635,2.479 0.542,0.24 10 false 1 5.083,1.667 5.625,1.906 0.542,0.24 10 false 2 5.073,1.01 5.615,1.25 0.542,0.24 10 false 4 5.073,0.427 5.615,0.667 0.542,0.24 10 false 3 3.708,0.438 4.25,0.677 0.542,0.24 10 false 2 3.708,1.042 4.25,1.281 0.542,0.24 10 false 3 3.698,2.26 4.24,2.5 0.542,0.24 10 false 1 1.438,0.677 1.979,0.917 0.542,0.24 10 false VSK 1.375,1.26 1.917,1.5 0.542,0.24 10 false SKS1 1.354,1.896 1.896,2.135 0.542,0.24 10 false SKS2 1.396,2.417 1.938,2.656 0.542,0.24 10 false SKG 1.844,1.76 2.385,2 0.542,0.24 10 false 23 1.833,1.125 2.375,1.365 0.542,0.24 10 false 22 1.833,0.563 2.375,0.802 0.542,0.24 10 false 2 1.854,2.344 2.396,2.583 0.542,0.24 10 false 8 5.417,0.646 5.958,0.885 0.542,0.24 10 false VSK 5.396,1.229 5.938,1.469 0.542,0.24 10 false SKS1 5.417,1.854 5.958,2.094 0.542,0.24 10 false SKS2 5.427,2.5 5.969,2.74 0.542,0.24 10 false SKG 3.708,1.667 4.25,1.906 0.542,0.24 10 false 4

CAUTION / NOTICE / HINT

NOTICE:

After replacing the electric brake booster (brake booster with master cylinder assembly), perform "Calibration" after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMMF, TMMCZ Made)>UTILITY


PROCEDURE

1.CONFIRM MODEL
a.

Choose the model to be inspected


Result:
Result Proceed to
for LHD A
for RHD B



A

2.REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

B

3.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - NO. 2 ENGINE ROOM WIRE ASSEMBLY)
2.REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

NEXT

END

3.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - NO. 2 ENGINE ROOM WIRE ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A35 electric brake booster (brake booster with master cylinder assembly) connector.


c.

Disconnect the AR1 No. 2 engine room wire assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A35-2 (VSK) - AR1-2 Always Below 1 Ω
A35-2 (VSK) or AR1-2 - Body ground Always 10 kΩ or higher
A35-22 (SKS1) - AR1-3 Always Below 1 Ω
A35-22 (SKS1) or AR1-3 - Body ground Always 10 kΩ or higher
A35-23 (SKS) - AR1-4 Always Below 1 Ω
A35-23 (SKS) or AR1-4 - Body ground Always 10 kΩ or higher
A35-8 (SKG) - AR1-1 Always Below 1 Ω
A35-8 (SKG) or AR1-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

NG

REPLACE NO. 2 ENGINE ROOM WIRE ASSEMBLY