The skid control ECU (brake actuator assembly) receives signals from the yaw rate and acceleration sensor (airbag sensor assembly) via CAN communication.
If there is a malfunction in the bus lines between the yaw rate and acceleration sensor (airbag sensor assembly) and the CAN communication system, DTC U012587 is output. When U012587 is output with C00611C, inspect and repair the trouble areas indicated by U012587 first.
These DTCs may be stored if one of the following occurs:
Yaw rate and acceleration sensor circuit malfunction.
Yaw rate and acceleration sensor (airbag sensor assembly) installation abnormality.
Yaw rate and acceleration sensor signal malfunction.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from |
|---|---|---|---|---|
| C00611C | Lateral Acceleration Sensor Circuit Voltage Out of Range | ·
While the vehicle is stopped, the lateral acceleration signal output value is outside the range of -7 to 7 m/s2 for 0.1 second or more. ·
When the vehicle is being driven straight ahead at a constant speed, the difference between the lateral acceleration signal output value and the control value calculated by the skid control ECU is outside the range of -5 to 5 m/s2 for 0.5 second or more. ·
When the vehicle is being driven at varying speeds and steered, the difference between the lateral acceleration signal output value and the control value calculated by the skid control ECU is outside the range of -11 to 11 m/s2 for 1.75 seconds or more. |
·
Acceleration sensor (airbag sensor assembly) ·
Acceleration sensor circuit ·
Acceleration sensor (airbag sensor assembly) installation |
Brake |
Inspect the fuses for circuits related to this system before performing the following procedure.
After replacing or reinstalling the yaw rate and acceleration sensor (airbag sensor assembly), perform yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".
Check that no CAN communication system DTCs are output.
| Result | Proceed to |
|---|---|
| CAN communication system DTCs are not output | A |
| CAN communication system DTCs are output | B |
A
B
Pre-procedure1
Operate the GTS to confirm the Data List.
Procedure1
Select the Data List on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Lateral G | Lateral G | Min.: -25.105 m/s2
Max.: 24.908 m/s2 |
Turning right: -25.105 to 0.000 m/s2
Turning left: 0.000 to 24.908 m/s2 |
During turning: Changes in proportion with lateral acceleration |
| Forward and Rearward G | Forward and Rearward G | Min.: -25.105 m/s2
Max.: 24.908 m/s2 |
During deceleration: -25.105 to 0.000 m/s2
During acceleration: 0.000 to 24.908 m/s2 |
During turning: Changes in proportion with lateral acceleration |
| Yaw Rate Sensor Value | Yaw rate sensor | Min.: -128°/s
Max.: 127°/s |
Vehicle stopped: 0°/s
Turning right: -128 to 0°/s Turning left: 0 to 127°/s |
- |
| Tester Display |
|---|
| Lateral G |
| Forward and Rearward G |
| Yaw Rate Sensor Value |
Check the yaw rate and acceleration sensor (airbag sensor assembly) output value displayed on the GTS.
The yaw rate and acceleration sensor (airbag sensor assembly) output value is normal.
Post-procedure1
Turn the ignition switch off.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Check that the yaw rate and acceleration sensor (airbag sensor assembly) has been installed properly.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION
The yaw rate and acceleration sensor (airbag sensor assembly) is tightened to the specified torque.
The yaw rate and acceleration sensor (airbag sensor assembly) is not installed in a tilted position.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION