Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF, TMMCZ Made) › from 2021.11
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0494155 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMMF, TMMCZ Made) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMMF, TMMCZ Made)  C006128  Lateral Acceleration Sensor Signal Bias Level Out of Range / Zero Adjustment Failure  C006328  Yaw Rate Sensor Signal Bias Level Out of Range / Zero Adjustment Failure  C055128  Longitudinal Acceleration Sensor Signal Bias Level Out of Range / Zero Adjustment Failure  


DESCRIPTION

The airbag sensor assembly has a built-in yaw rate and acceleration sensor and detects the vehicle condition.

When an abnormal yaw rate and acceleration sensor offset value has been detected, the skid control ECU (brake actuator assembly) stores the following DTCs.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
C006128 Lateral Acceleration Sensor Signal Bias Level Out of Range / Zero Adjustment Failure The calculated offset value for the lateral acceleration signal is outside the range of -1.7 to 1.7 m/s2.
·

Acceleration sensor (airbag sensor assembly)

·

Acceleration sensor (airbag sensor assembly) installation


Brake
C006328 Yaw Rate Sensor Signal Bias Level Out of Range / Zero Adjustment Failure The calculated offset value for the yaw rate sensor signal is outside the range of -6.0 to 6.0°/s.
·

Yaw rate sensor (airbag sensor assembly)

·

Yaw rate sensor (airbag sensor assembly) installation


Brake
C055128 Longitudinal Acceleration Sensor Signal Bias Level Out of Range / Zero Adjustment Failure The calculated offset value for the longitudinal acceleration signal is outside the range of -1.9 to 1.9 m/s2.
·

Acceleration sensor (airbag sensor assembly)

·

Acceleration sensor (airbag sensor assembly) installation


Brake

CAUTION / NOTICE / HINT

NOTICE:

After replacing or reinstalling the yaw rate and acceleration sensor (airbag sensor assembly), perform yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF, TMMCZ Made)>UTILITY


PROCEDURE

1.CHECK AIRBAG SENSOR ASSEMBLY INSTALLATION
a.

Check that the yaw rate and acceleration sensor (airbag sensor assembly) has been installed properly.

HINT:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION


OK:

The yaw rate and acceleration sensor (airbag sensor assembly) is tightened to the specified torque.

The yaw rate and acceleration sensor (airbag sensor assembly) is not installed in a tilted position.



Result:
Proceed to
OK
NG



OK

2.CLEAR ZERO POINT CALIBRATION DATA

NG

2.CLEAR ZERO POINT CALIBRATION DATA
a.

Clear the zero point calibration data and system information.

Chassis > Brake > Utility
Tester Display
Reset Memory
50005 435 4560

Result:
Proceed to
NEXT



NEXT

3.PERFORM ZERO POINT CALIBRATION
3.PERFORM ZERO POINT CALIBRATION
a.

Operate the GTS to perform "Calibration" and store system information memorization.

Chassis > Brake > Utility
Tester Display
Calibration
50005 435 4554

Result:
Proceed to
NEXT



NEXT

4.CLEAR DTC
4.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

b.

Operate the GTS to clear the codes.

Chassis > Brake > Clear DTCs
50002 435

Post-procedure1

c.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

5.RECONFIRM DTC
5.RECONFIRM DTC

Pre-procedure1

a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


Procedure1

b.

Operate the GTS to read the DTCs.

Chassis > Brake > Trouble Codes
50001 435

c.

Check if the same DTC is output.


Post-procedure1

d.

Turn the ignition switch off.


Result:
Result Proceed to
C006128, C006328 and C055128 are not output OK
C006128, C006328 or C055128 is output NG



OK

END

NG