Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM (for HV Model) › from 2021.11
RM36W0E _51 Engine / Hybrid System _088664 CRUISE CONTROL _0424997 DYNAMIC RADAR CRUISE CONTROL SYSTEM(for HV Model) C

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM(for HV Model)  P057162  Brake Switch "A" Signal Compare Failure  


DESCRIPTION

When the brake pedal is depressed, the stop light switch assembly outputs a signal to the hybrid vehicle control ECU. The hybrid vehicle control ECU uses this signal to control cancellation of vehicle speed by the dynamic radar cruise control. When the hybrid vehicle control ECU determines that terminals STP and ST1- of the stop light switch assembly are both less than 1 V, DTC P057162 is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
P057162 Brake Switch "A" Signal Compare Failure When the ignition switch is ON and the dynamic radar cruise control system is operating, the hybrid vehicle control ECU detects that the voltage at terminal STP and ST1- are both less than 1 V for approximately 0.5 seconds or more.
·

Harness or connector

·

Stop light switch assembly

·

Hybrid vehicle control ECU


Radar Cruise1

WIRING DIAGRAM

for TMC Made


C432274E09
5.323,3.875 6.896,4.25 1.573,0.375 10 false Certification ECU (Smart Key ECU Assembly)* 2.833,3.885 5,4.417 2.167,0.531 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 5.333,3.688 5.792,3.885 0.458,0.198 10 false H45 2.833,3.698 3.292,3.896 0.458,0.198 10 false A38 3.906,3.302 4.365,3.5 0.458,0.198 10 false STP2 5.76,3.292 6.219,3.49 0.458,0.198 10 false STP1 4.354,3.208 4.688,3.406 0.333,0.198 10 false 37 5.51,3.208 5.823,3.406 0.313,0.198 10 false 21 2.958,2.49 6.938,2.688 3.979,0.198 10 false Stop Light Switch Assembly 2.969,2.323 3.427,2.521 0.458,0.198 10 false A63 5.479,1.469 5.792,1.667 0.313,0.198 10 false 5 5.49,0.667 5.802,0.865 0.313,0.198 10 false 6 5.677,1.563 6.135,1.76 0.458,0.198 10 false ST1- 5.677,0.76 6.135,0.958 0.458,0.198 10 false STP 5.313,2.458 7.073,2.677 1.76,0.219 10 false Hybrid Vehicle Control ECU 4.167,0.75 4.479,0.948 0.313,0.198 10 false L 4.156,1.552 4.469,1.75 0.313,0.198 10 false L 3.573,0.885 3.885,1.083 0.313,0.198 10 false B 3.573,1.396 3.885,1.594 0.313,0.198 10 false B 3.573,1.906 3.885,2.104 0.313,0.198 10 false GND 4.333,0.677 4.646,0.875 0.313,0.198 10 false 3 4.344,1.469 4.656,1.667 0.313,0.198 10 false 5 3.406,0.792 3.719,0.99 0.313,0.198 10 false 7 3.406,1.292 3.719,1.49 0.313,0.198 10 false 6 3.396,1.813 3.708,2.01 0.313,0.198 10 false 2 2.396,1.052 3.01,1.25 0.615,0.198 10 false STOP 2.073,1.573 3.115,1.833 1.042,0.26 10 false ECU-IGP NO. 3 0.438,0.875 1.677,1.219 1.24,0.344 10 false from AM1 Fuse 0.458,1.417 1.469,1.792 1.01,0.375 10 false from IGP Relay 5.313,2.281 5.771,2.479 0.458,0.198 10 false A68 0.229,4.281 2.302,4.625 2.073,0.344 10 false *: w/ Entry and Start System


for TMMF, TMMCZ Made


C442005E10
5.542,4.177 7.115,4.552 1.573,0.375 10 false Certification ECU (Smart Key ECU Assembly)*3 2.719,3.063 4.823,3.479 2.104,0.417 10 false Skid Control ECU (Brake Actuator Assembly) 5.531,4 5.99,4.198 0.458,0.198 10 false H45 2.74,2.917 3.198,3.115 0.458,0.198 10 false A39 3.656,2.583 4.115,2.781 0.458,0.198 10 false STP 6.021,3.74 6.479,3.938 0.458,0.198 10 false STP1 4.021,2.479 4.354,2.677 0.333,0.198 10 false 41 5.771,3.635 6.083,3.833 0.313,0.198 10 false 21 2.99,2.052 4.771,2.271 1.781,0.219 10 false Stop Light Switch Assembly 3.021,1.927 3.479,2.125 0.458,0.198 10 false A63 5.594,1.156 5.906,1.354 0.313,0.198 10 false 5 5.594,0.365 5.906,0.563 0.313,0.198 10 false 6 5.792,1.25 6.25,1.448 0.458,0.198 10 false ST1- 5.792,0.479 6.25,0.677 0.458,0.198 10 false STP 5.396,2.01 7.156,2.229 1.76,0.219 10 false Hybrid Vehicle Control ECU 4.167,0.469 4.479,0.667 0.313,0.198 10 false L 4.156,1.271 4.469,1.469 0.313,0.198 10 false L 3.573,0.594 3.885,0.792 0.313,0.198 10 false B 3.573,1.094 3.885,1.292 0.313,0.198 10 false B 3.563,1.573 3.875,1.771 0.313,0.198 10 false GND 4.333,0.396 4.646,0.594 0.313,0.198 10 false 3 4.344,1.146 4.656,1.344 0.313,0.198 10 false 5 3.406,0.49 3.719,0.688 0.313,0.198 10 false 7 3.406,0.979 3.719,1.177 0.313,0.198 10 false 6 3.396,1.479 3.708,1.677 0.313,0.198 10 false 2 2.396,0.75 3.01,0.948 0.615,0.198 10 false STOP 2.073,1.281 3.115,1.542 1.042,0.26 10 false ECU-IGP NO. 3 0.115,0.427 1.427,1.01 1.313,0.583 10 false for STRG LOCK Fuse*3, AM1 Fuse*4 0.448,1.063 1.458,1.438 1.01,0.375 10 false from IGP Relay 5.396,1.813 5.854,2.01 0.458,0.198 10 false A68 0.219,4.177 2.292,4.521 2.073,0.344 10 false *4: w/o Entry and Start System 5.063,2.969 7.104,3.396 2.042,0.427 10 false No. 1 Skid Control ECU (Booster With Master Cylinder Assembly) 0.208,3.073 2.281,3.417 2.073,0.344 10 false *2: for RHD 0.188,2.521 2.26,2.865 2.073,0.344 10 false *1: for LHD 5.396,2.75 5.708,2.948 0.313,0.198 10 false *1 5.771,2.75 6.083,2.948 0.313,0.198 10 false *2 6.021,2.583 6.333,2.781 0.313,0.198 10 false STP 5.688,2.583 6,2.781 0.313,0.198 10 false A35 5.354,2.583 5.667,2.781 0.313,0.198 10 false A34 5.385,2.396 5.698,2.594 0.313,0.198 10 false 21 5.729,2.385 6.042,2.583 0.313,0.198 10 false 21 0.219,3.635 2.292,3.979 2.073,0.344 10 false *3: w/ Entry and Start System


CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the hybrid vehicle control ECU, refer to Service Bulletin.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BODY GROUND)
a.

Disconnect the A63 stop light switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A63-2 (GND) - Body ground Always Below 1 Ω



c.

Connect the A63 stop light switch assembly connector.


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - AUXILIARY BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - AUXILIARY BATTERY)
a.

Disconnect the A63 stop light switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A63-7 (B) - Body ground Always 11 to 14 V
A63-6 (B) - Body ground Ignition switch ON 11 to 14 V
A63-6 (B) - Body ground Ignition switch off Below 1 V



c.

Connect the A63 stop light switch assembly connector.


Result:
Proceed to
OK
NG



OK

3.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT STOP LIGHT SWITCH ASSEMBLY

OK

4.CONFIRM MODEL

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

4.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for TMC Made A
for TMMF, TMMCZ Made B



A

5.CONFIRM MODEL

B

8.CONFIRM MODEL
5.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
w/ Entry and Start System A
w/o Entry and Start System B



A

6.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - STOP LIGHT SWITCH ASSEMBLY)

B

7.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - STOP LIGHT SWITCH ASSEMBLY)
6.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the A68 hybrid vehicle control ECU connectors.


b.

Disconnect the A63 stop light switch assembly connector.


c.

Disconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.


d.

Disconnect the H45 certification ECU (smart key ECU assembly) connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A68-5 (ST1-) - A63-5 (L) Always Below 1 Ω
A68-6 (STP) - A63-3 (L) Always Below 1 Ω
A68-5 (ST1-) or A63-5 (L) - Body ground Always 10 kΩ or higher
A68-6 (STP) or A63-3 (L) - Body ground Always 10 kΩ or higher



f.

Connect the H45 certification ECU (smart key ECU assembly) connector.


g.

Connect the A38 skid control ECU (brake booster with master cylinder assembly) connector.


h.

Connect the A63 stop light switch assembly connector.


i.

Connect the A68 hybrid vehicle control ECU connectors.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the A68 hybrid vehicle control ECU connectors.


b.

Disconnect the A63 stop light switch assembly connector.


c.

Disconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A68-5 (ST1-) - A63-5 (L) Always Below 1 Ω
A68-6 (STP) - A63-3 (L) Always Below 1 Ω
A68-5 (ST1-) or A63-5 (L) - Body ground Always 10 kΩ or higher
A68-6 (STP) or A63-3 (L) - Body ground Always 10 kΩ or higher



e.

Connect the A38 skid control ECU (brake booster with master cylinder assembly) connector.


f.

Connect the A63 stop light switch assembly connector.


g.

Connect the A68 hybrid vehicle control ECU connectors.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
w/ Entry and Start System A
w/o Entry and Start System B



A

9.CONFIRM MODEL

B

12.CONFIRM MODEL
9.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for LHD A
for RHD B



A

10.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - STOP LIGHT SWITCH ASSEMBLY)

B

11.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - STOP LIGHT SWITCH ASSEMBLY)
10.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the A68 hybrid vehicle control ECU connectors.


b.

Disconnect the A63 stop light switch assembly connector.


c.

Disconnect the A34 No. 1 skid control ECU (booster with master cylinder assembly) connector.


d.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


e.

Disconnect the H45 certification ECU (smart key ECU assembly) connector.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A68-5 (ST1-) - A63-5 (L) Always Below 1 Ω
A68-6 (STP) - A63-3 (L) Always Below 1 Ω
A68-5 (ST1-) or A63-5 (L) - Body ground Always 10 kΩ or higher
A68-6 (STP) or A63-3 (L) - Body ground Always 10 kΩ or higher



g.

Connect the H45 certification ECU (smart key ECU assembly) connector.


h.

Connect the A39 skid control ECU (brake actuator assembly) connector.


i.

Connect the A34 No. 1 skid control ECU (booster with master cylinder assembly) connector.


j.

Connect the A63 stop light switch assembly connector.


k.

Connect the A68 hybrid vehicle control ECU connectors.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the A68 hybrid vehicle control ECU connectors.


b.

Disconnect the A63 stop light switch assembly connector.


c.

Disconnect the A35 No. 1 skid control ECU (booster with master cylinder assembly) connector.


d.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


e.

Disconnect the H45 certification ECU (smart key ECU assembly) connector.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A68-5 (ST1-) - A63-5 (L) Always Below 1 Ω
A68-6 (STP) - A63-3 (L) Always Below 1 Ω
A68-5 (ST1-) or A63-5 (L) - Body ground Always 10 kΩ or higher
A68-6 (STP) or A63-3 (L) - Body ground Always 10 kΩ or higher



g.

Connect the H45 certification ECU (smart key ECU assembly) connector.


h.

Connect the A39 skid control ECU (brake actuator assembly) connector.


i.

Connect the A35 No. 1 skid control ECU (booster with master cylinder assembly) connector.


j.

Connect the A63 stop light switch assembly connector.


k.

Connect the A68 hybrid vehicle control ECU connectors.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for LHD A
for RHD B



A

13.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - STOP LIGHT SWITCH ASSEMBLY)

B

14.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - STOP LIGHT SWITCH ASSEMBLY)
13.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the A68 hybrid vehicle control ECU connectors.


b.

Disconnect the A63 stop light switch assembly connector.


c.

Disconnect the A34 No. 1 skid control ECU (booster with master cylinder assembly) connector.


d.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A68-5 (ST1-) - A63-5 (L) Always Below 1 Ω
A68-6 (STP) - A63-3 (L) Always Below 1 Ω
A68-5 (ST1-) or A63-5 (L) - Body ground Always 10 kΩ or higher
A68-6 (STP) or A63-3 (L) - Body ground Always 10 kΩ or higher



f.

Connect the A39 skid control ECU (brake actuator assembly) connector.


g.

Connect the A34 No. 1 skid control ECU (booster with master cylinder assembly) connector.


h.

Connect the A63 stop light switch assembly connector.


i.

Connect the A68 hybrid vehicle control ECU connectors.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the A68 hybrid vehicle control ECU connectors.


b.

Disconnect the A63 stop light switch assembly connector.


c.

Disconnect the A35 No. 1 skid control ECU (booster with master cylinder assembly) connector.


d.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A68-5 (ST1-) - A63-5 (L) Always Below 1 Ω
A68-6 (STP) - A63-3 (L) Always Below 1 Ω
A68-5 (ST1-) or A63-5 (L) - Body ground Always 10 kΩ or higher
A68-6 (STP) or A63-3 (L) - Body ground Always 10 kΩ or higher



f.

Connect the A39 skid control ECU (brake actuator assembly) connector.


g.

Connect the A35 No. 1 skid control ECU (booster with master cylinder assembly) connector.


h.

Connect the A63 stop light switch assembly connector.


i.

Connect the A68 hybrid vehicle control ECU connectors.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR