Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › COOLANT (for Inverter) › from 2021.11
RM36W0E _51 Engine / Hybrid System _087936 HYBRID / BATTERY CONTROL _0424570 COOLANT(for Inverter) A

HYBRID / BATTERY CONTROL  COOLANT(for Inverter)  REPLACEMENT  


CAUTION / NOTICE / HINT

CAUTION:

To avoid the danger of being burned, do not remove the reserve tank cap or drain cock plug while the coolant (for inverter) is still hot. Pressurized, hot coolant (for inverter) and steam may be released and cause serious burns.

A464256C01
4.833,1.667 5,1.667 5,1.667 5.25,1.313 true 5.917,3.583 6.083,3.917 6.083,3.917 6.25,3.917 true 4.604,1.542 4.792,1.76 0.188,0.219 10 true *1 6.281,3.823 6.479,4.031 0.198,0.208 10 true *2
*1 Reserve Tank Cap *2 Drain Cock Plug



PROCEDURE

Hide 53876A 1.SEPARATE FRONT FENDER LINER LH

a.
A476031

Remove the 2 screws and clip.


b.
A476032

Separate the front fender liner LH.


Hide 2.DRAIN COOLANT (for Inverter)

CAUTION:

To avoid the danger of being burned, do not remove the reserve tank cap while the coolant (for inverter) is still hot. Pressurized, hot coolant (for inverter) and steam may be released and cause serious burns.


NOTICE:
·

Do not reuse the drained coolant because it may contain foreign matter.

·

Collect the drained coolant and measure its volume to establish a benchmark. When adding coolant, make sure to add more coolant than the measured amount.



a.

Remove the reserve tank cap from the inverter reserve tank assembly.


b.
A476037

Connect a hose with an inside diameter of 9 mm (0.354 in.) to the radiator drain cock as shown in the illustration.


c.

Loosen the drain cock plug indicated in the illustration and drain the coolant.

CAUTION:

To avoid the danger of being burned, do not loosen the drain cock plug while the coolant (for inverter) is still hot. Pressurized, hot coolant (for inverter) and steam may be released and cause serious burns.



d.

Tighten the drain cock plug by hand.


e.

Disconnect the hose from the radiator drain cock.


Hide 3.ADD COOLANT (for Inverter)

NOTICE:
·

Do not reuse the drained coolant because it may contain foreign matter.

·

If the vehicle is driven with air in the inverter cooling system, damage may occur and the following DTCs may be stored.

DTC No. Detection Item
P0A9300 Inverter "A" Cooling System
P0C7396 Motor Electronics Coolant Pump "A" Component Internal Failure
P0A001C Motor Electronics Coolant Temperature Sensor Circuit Voltage Out of Range
P0A001F Motor Electronics Coolant Temperature Sensor Circuit Intermittent
P0A789E Drive Motor "A" Inverter Stuck On
P1C5D19 Drive Motor "A" Inverter Circuit Current Above Threshold
P0A7A9E Generator Inverter Stuck On
P1C5F19 Generator Inverter Circuit Current Above Threshold
P0A949E DC/DC Converter Stuck On
P0D3319 DC/DC Converter Circuit Current Above Threshold
P0AED1C Drive Motor Inverter Temperature Sensor "A" Circuit Voltage Out of Range
P0AED1F Drive Motor Inverter Temperature Sensor "A" Circuit Intermittent
P0C381C DC/DC Converter Temperature Sensor "A" Circuit Voltage Out of Range
P0C381F DC/DC Converter Temperature Sensor "A" Circuit Intermittent
P0C3D1C DC/DC Converter Temperature Sensor "B" Circuit Voltage Out of Range
P0C3D1F DC/DC Converter Temperature Sensor "B" Circuit Intermittent
P1CCC96 DC/DC Converter Enable Component Internal Failure



a.
A457829

Slowly pour coolant into the inverter reserve tank assembly until it reaches the F line.

Specified Capacity:
Item Specified Condition
for TMC made 1.6 liters (1.7 US qts, 1.4 Imp. qts)
for TMMF, TMMCZ Made 1.3 liters (1.4 US qts, 1.1 Imp. qts)


NOTICE:

To prevent foreign matter such as dust or dirt from entering the cooling system, make sure to confirm that the container used to add coolant is clean and free of foreign matter.



b.

When using the GTS:

i.

Connect the GTS to the DLC3.


ii.

Turn the ignition switch on (IG).


iii.

Enter the following menus: Powertrain / Hybrid Control / Active Test / Activate the Inverter Water Pump.

Powertrain > Hybrid Control > Active Test
Tester Display
Activate the Inverter Water Pump
50004 397 1

iv.

While adding coolant to the inverter reserve tank assembly to keep the coolant at the FULL line and compensate for the drop in the coolant level as the air bleeds, operate and stop the inverter water pump assembly at 1 minute intervals.

Standard:

Air bleeding from the inverter cooling system is completed when the noise made by the inverter water pump assembly becomes smaller and the circulation of coolant in the inverter reserve tank assembly improves.


HINT:

Loud noises made by the inverter water pump assembly and poor circulation of coolant in the inverter reserve tank assembly indicate that there is air in the cooling system.




c.

When not using the GTS:

i.

Turn the ignition switch on (READY). [*1]


ii.

Turn the ignition switch off and add coolant to the FULL line as the coolant level will drop as the air bleeds. [*2]

NOTICE:
·

Be sure to turn the ignition switch off before adding SLLC.

·

Do not work on the components in the engine compartment while the ignition switch is on (READY) as the engine will operate intermittently.




iii.

Repeat steps [*1] and [*2] until air bleeding from the cooling system is completed.

Standard:

Air bleeding from the inverter cooling system is completed when the noise made by the inverter water pump assembly becomes smaller and the circulation of coolant in the inverter reserve tank assembly improves.


HINT:

Loud noises made by the inverter water pump assembly and poor circulation of coolant in the inverter reserve tank assembly indicate that there is air in the cooling system.




d.
A457829

After the air is completely bled from the cooling system, add coolant to the FULL line of inverter reserve tank assembly and install the reserve tank cap.


Hide 53876A 5.INSTALL FRONT FENDER LINER LH

a.

Install the front fender liner LH.


b.

Install the 2 screws and clip.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)