Home › Vehicle Exterior › LIGHTING (EXT) › HEADLIGHT ASSEMBLY (for Halogen Headlight) › from 2021.11
RM36W0E _59 Vehicle Exterior _087824 LIGHTING (EXT) _0421009 HEADLIGHT ASSEMBLY(for Halogen Headlight) A

LIGHTING (EXT)  HEADLIGHT ASSEMBLY(for Halogen Headlight)  REASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:
·

Handle components indoors as much as possible to prevent foreign matter from entering and adhering to headlight assembly components.

·

Do not reuse parts which have reduced fastening ability due to thread damage.

·

When installing components, make sure that the wire harness is not pinched or pulled.

·

Do not use solvent to clean components. Only clean them with a dry cloth.



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.INSTALL HEADLIGHT HOUSING SUB-ASSEMBLY

HINT:

As the headlight housing sub-assembly is available as a supply part, proceed to the next step if it is necessary to change the headlight housing sub-assembly.


a.
E450098

Install the pivot screw.


b.
E450099

Engage the claws to install a new aiming screw.


Hide 81175 2.INSTALL HEADLIGHT UNIT ASSEMBLY

NOTICE:
·

Make sure to wear clean rubber gloves when performing this procedure.

·

Do not allow dirt or foreign matter to get on the headlight unit assembly or other components.

·

Prevention of static electricity is required during this procedure.

·

Use static electricity countermeasures SST (desktop anti-static mat set) and observe all precautions to prevent damage to the system by electrostatic discharge (ESD).

·

Do not touch the headlight unit assembly with bare hands.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

If there are any fingerprints or foreign matter on the headlight unit assembly or other components, wipe them off with a soft cloth.

·

Do not use solvent to clean components. Only clean them with a dry cloth.



SST
09890-47010  (09891-04010, 09891-04020, 09891-04030, 09891-04040)

a.

When reusing the headlight unit assembly:

i.
E438680

Engage the claws to install a new pivot collar.



b.
E438681C01
0,0 0,0 false
V113147

Install in this Direction


Temporarily install the headlight unit assembly as shown in the illustration.


c.
E438682

While holding the headlight unit assembly by hand, turn the aiming screws as shown in the illustration to install the headlight unit assembly.

HINT:

Turn the aiming screws the same number of times as they were turned during removal.



d.
E438683

Engage the pivot collar and clamp.


e.
E438673

Engage the claws.


Hide 3.INSTALL NO. 1 HEADLIGHT REFLECTOR (for TMC Made)

NOTICE:
·

Make sure to wear clean rubber gloves when performing this procedure.

·

Do not allow dirt or foreign matter to get on the No. 1 headlight reflector or other components.

·

Do not touch the No. 1 headlight reflector with bare hands.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

If there are any fingerprints or foreign matter on the No. 1 headlight reflector or other components, wipe them off with a soft cloth.

·

Do not use solvent to clean components. Only clean them with a dry cloth.



a.
E438671

Engage the claw to install the No.1 headlight reflector.


b.

Install the screw.


Hide 4.INSTALL NO. 1 HEADLIGHT REFLECTOR (for TMMF, TMMCZ Made)

NOTICE:
·

Make sure to wear clean rubber gloves when performing this procedure.

·

Do not allow dirt or foreign matter to get on the No. 1 headlight reflector or other components.

·

Do not touch the No. 1 headlight reflector with bare hands.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

If there are any fingerprints or foreign matter on the No. 1 headlight reflector or other components, wipe them off with a soft cloth.

·

Do not use solvent to clean components. Only clean them with a dry cloth.



a.
E444069

Engage the claw to install the No. 1 headlight reflector.


b.

Install the 2 screws.


Hide 5.INSTALL NO. 2 HEADLIGHT REFLECTOR (for TMC Made)

NOTICE:
·

Make sure to wear clean rubber gloves when performing this procedure.

·

Do not allow dirt or foreign matter to get on the No. 2 headlight reflector or other components.

·

Do not touch the No. 2 headlight reflector with bare hands.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

If there are any fingerprints or foreign matter on the No. 2 headlight reflector or other components, wipe them off with a soft cloth.

·

Do not use solvent to clean components. Only clean them with a dry cloth.



a.
E438672

Install the No. 2 headlight reflector with 3 screws.


Hide 6.INSTALL NO. 2 HEADLIGHT REFLECTOR (for TMMF, TMMCZ Made)

NOTICE:
·

Make sure to wear clean rubber gloves when performing this procedure.

·

Do not allow dirt or foreign matter to get on the No. 2 headlight reflector or other components.

·

Do not touch the No. 2 headlight reflector with bare hands.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

If there are any fingerprints or foreign matter on the No. 2 headlight reflector or other components, wipe them off with a soft cloth.

·

Do not use solvent to clean components. Only clean them with a dry cloth.



a.
E444070

Engage the claws to install the No. 2 headlight reflector.


Hide 81134 7.INSTALL HEADLIGHT GASKET

NOTICE:
·

The headlight lens gasket must not be reused.

·

Make sure to wear clean rubber gloves when performing this procedure.

·

Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

If there are any fingerprints or foreign matter on the headlight unit assembly or other components, wipe them off with a soft cloth.

·

Do not use solvent to clean components. Only clean them with a dry cloth.



a.

Completely remove the old headlight gasket.


b.
E438684C01
0,0 0,0 false
V100155

Cleaning Area


Clean the installation groove of the headlight lens sub-assembly.


c.
E237693C09
1.323,1.281 1.365,1.042 false 0.625,1.125 0.667,0.896 false 1.229,1.292 1.531,1.542 0.302,0.25 10 false *a 0.531,1.146 0.865,1.396 0.333,0.25 10 false *b 1.479,1.875 2.01,2.177 0.531,0.302 10 false *c 1.521,0.542 1.677,0.74 0.156,0.198 10 false 1 0.302,0.635 0.458,0.833 0.156,0.198 10 false 2
*a Release Paper
*b Tape
*c 90°


Partially remove the release paper from a new headlight gasket, and cut off a piece of it.


d.

Fold the release paper over the tip of a screwdriver and secure it in place with tape as indicated by the arrows, in the order shown in the illustration.


e.

Using scissors, cut the end of the headlight gasket at a 90° angle.


f.
E438685C01
0.625,2.802 0.938,2.958 0.313,0.156 10 false *a
*a 5 to 15 mm


Install a new headlight gasket as shown in the illustration.


g.

Using a screwdriver with their tips wrapped with release paper, completely press the headlight gasket into the groove to install it.


Hide 8110B 8.INSTALL HEADLIGHT LENS SUB-ASSEMBLY

NOTICE:
·

Make sure to wear clean rubber gloves when performing this procedure.

·

Do not allow dirt or foreign matter to get on the headlight lens.

·

Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

If there are any fingerprints or foreign matter on the back of the headlight lens sub-assembly, wipe them off with a soft cloth.

·

Do not use solvent to clean components. Only clean them with a dry cloth.



a.

Clean the sealing surface of the headlight lens sub-assembly.


b.
E431597

Engage the claws to install the headlight lens sub-assembly to the headlight housing sub-assembly.

NOTICE:

Make sure all of the claws are engaged.



c.
E431593

Install the 9 screws.


d.

Check the installation condition of the headlight gasket.

NOTICE:

Make sure the headlight gasket is not protruding and completely contacts the headlight lens sub-assembly.



Hide 85669 9.INSTALL HEADLIGHT LEVELING MOTOR BASE PACKING

a.
E431589

Install a new headlight leveling motor base packing.


Hide 85662 10.INSTALL HEADLIGHT LEVELING MOTOR (for TMC Made)

a.
E431605C01
0,0 0,0 false
V113147

Install in this Direction


Install the headlight leveling motor as shown in the illustration.


b.
E431606

Turn the aiming screw as shown in the illustration.

HINT:

Turn the aiming screw the same number of times as they were turned during removal.



Hide 85662 11.INSTALL HEADLIGHT LEVELING MOTOR (for TMMF, TMMCZ Made)

a.
E450100C01
0,0 0,0 false
V113147

Install in this Direction


Install the headlight leveling motor as shown in the illustration.


b.
E450101

Turn the aiming screw as shown in the illustration.

HINT:

Turn the aiming screw the same number of times as they were turned during removal.



Hide 81510D 12.INSTALL FRONT TURN SIGNAL LIGHT BULB

a.
E431583

Install the front turn signal light bulb to the front turn signal light socket.


b.
E431611C01
0,0 0,0 false
V113147

Install in this Direction


Turn the front turn signal light socket with the front turn signal light bulb as shown in the illustration to install it.


Hide 81610F 13.INSTALL CLEARANCE LIGHT BULB

a.
E431581

Install the clearance light bulb to the clearance light socket.


b.
E431613C01
0,0 0,0 false
V113147

Install in this Direction


Turn the clearance light socket with the clearance light bulb as shown in the illustration to install it.


Hide 81135F 14.INSTALL HEADLIGHT BACK COVER

a.
E431579

Install the headlight back cover.


Hide 81110B 15.INSTALL NO. 1 HEADLIGHT BULB

a.
E431614C01
0,0 0,0 false
V113147

Install in this Direction


Turn the No.1 headlight bulb as shown in the illustration.


Hide 8158AJ 16.INSTALL DAYTIME RUNNING LIGHT LED

E431609C01
0,0 0,0 false
V113147

Install in this Direction


a.

Install the daytime running light LED as shown in the illustration.