Home › Vehicle Exterior › LIGHTING (EXT) › HEADLIGHT ASSEMBLY (for LED Headlight) › from 2021.11
RM36W0E _59 Vehicle Exterior _087824 LIGHTING (EXT) _0421010 HEADLIGHT ASSEMBLY(for LED Headlight) A

LIGHTING (EXT)  HEADLIGHT ASSEMBLY(for LED Headlight)  DISASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:
·

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Headlight)>PRECAUTION

·

Handle components indoors as much as possible to prevent foreign matter from entering and adhering to headlight assembly components.

·

Do not reuse parts which have reduced fastening ability due to thread damage.

·

Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

When installing components, make sure that the wire harness is not pinched or pulled.

·

Do not use solvent to clean components. Only clean them with a dry cloth.



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 85662 1.REMOVE HEADLIGHT LEVELING MOTOR (for TMC Made)

a.
E431587

Turn the aiming screws as shown in the illustration until the aiming screws are disconnected from the headlight unit.

HINT:

Make sure to remember the number of aiming screw rotations.



b.
E431588C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the headlight leveling motor as shown in the illustration.


Hide 85662 2.REMOVE HEADLIGHT LEVELING MOTOR (for TMMF, TMMCZ Made)

a.
E450103

Turn the aiming screws as shown in the illustration until the aiming screws are disconnected from the headlight unit.

HINT:

Make sure to remember the number of aiming screw rotations.



b.
E450104C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the headlight leveling motor as shown in the illustration.


Hide 85669 3.REMOVE HEADLIGHT LEVELING MOTOR BASE PACKING

a.
E431590

Remove the headlight leveling motor base packing.

NOTICE:

The headlight leveling motor base packing must not be reused.



Hide 4.REMOVE HEADLIGHT COVER

a.
E431591C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the headlight cover as shown in the illustration.


Hide 8110B 5.REMOVE HEADLIGHT LENS SUB-ASSEMBLY

NOTICE:
·

Make sure to wear clean rubber gloves when performing this procedure.

·

Do not allow dirt or foreign matter to get on the headlight lens sub-assembly.

·

Prevention of static electricity is required during this procedure.

·

Use static electricity countermeasures SST (desktop anti-static mat set) and observe all precautions to prevent damage to the system by electrostatic discharge (ESD).

·

Do not touch the headlight lens sub-assembly with bare hands.

·

Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

If there are any fingerprints or foreign matter on the back of the headlight lens sub-assembly, wipe them off with a soft cloth.

·

Do not use solvent to clean components. Only clean them with a dry cloth.



SST
09890-47010  (09891-04010, 09891-04020, 09891-04030, 09891-04040)

a.
E431592

Disconnect the connector.


b.
E431594

Remove the 9 screws.


c.
E431596

Using a hair dryer, heat the backside of the headlight assembly.

NOTICE:

If the headlight assembly is heated unevenly, it will deform or melt.



d.
E431598

Disengage the claws to remove the headlight lens sub-assembly.

HINT:

If the headlight lens sub-assembly cannot be separated even after heating, using a screwdriver with its tip wrapped with protective tape, lift the headlight lens sub-assembly. Be careful not to damage the headlight lens sub-assembly and headlight housing sub-assembly.



Hide 81134 6.REMOVE HEADLIGHT GASKET

NOTICE:
·

The headlight gasket must not be reused.

·

Make sure to wear clean rubber gloves when performing this procedure.

·

Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

If there are any fingerprints or foreign matter on the headlight unit assembly or other components, wipe them off with a soft cloth.

·

Do not use solvent to clean components. Only clean them with a dry cloth.



a.
E431600

Remove the headlight gasket from the headlight housing sub-assembly.

NOTICE:

Make sure to replace the headlight gasket with a new one. Failure to do so may cause water ingress.



Hide 85967D 7.REMOVE LIGHT CONTROL LED ECU

NOTICE:
·

Make sure to wear clean rubber gloves when performing this procedure.

·

Do not allow dirt or foreign matter to get on the headlight unit or other components.

·

Prevention of static electricity is required during this procedure.

·

Use static electricity countermeasures SST (desktop anti-static mat set) and observe all precautions to prevent damage to the system by electrostatic discharge (ESD).

·

Do not touch the headlight unit with bare hands.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

If there are any fingerprints or foreign matter on the headlight unit or other components, wipe them off with a soft cloth.

·

Do not use solvent to clean components. Only clean them with a dry cloth.



SST
09890-47010  (09891-04010, 09891-04020, 09891-04030, 09891-04040)

a.
E431601

Disconnect the connector.


b.
E431602

Remove the screw.


c.

Disengage the guide to remove the light control LED ECU.


Hide 81175 8.REMOVE HEADLIGHT UNIT ASSEMBLY

NOTICE:
·

Make sure to wear clean rubber gloves when performing this procedure.

·

Do not allow dirt or foreign matter to get on the headlight unit or other components.

·

Prevention of static electricity is required during this procedure.

·

Use static electricity countermeasures SST (desktop anti-static mat set) and observe all precautions to prevent damage to the system by electrostatic discharge (ESD).

·

Do not touch the headlight unit with bare hands.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

If there are any fingerprints or foreign matter on the headlight unit or other components, wipe them off with a soft cloth.

·

Do not use solvent to clean components. Only clean them with a dry cloth.



SST
09890-47010  (09891-04010, 09891-04020, 09891-04030, 09891-04040)

a.
E438686

Disconnect the connector.


b.

Disengage the claws.


c.
E438687

While holding the headlight unit assembly by hand, turn the aiming screw as shown in the illustration until the aiming screw are disconnected from the headlight unit assembly.

HINT:

Make sure to remember the number of aiming screw rotations.



d.
E438688C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the headlight unit assembly from the headlight housing sub-assembly as shown in the illustration.


e.

When installing a new headlight unit assembly:

i.
E438690

Disengage clamp to remove the pivot collar.



Hide 9.REMOVE WIRE HARNESS

a.
E438689C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the clamp.


b.

Disengage the claws to remove the wire harness.