2005-2008 Yaris · Service Manual TRANSMISSION

INSTALLATION

Removal / installation · Vehicles built from Aug 2005


1. INSTALL TRANSMISSION CASE OIL SEAL
  1. Coat the lip of a new oil seal with MP grease.

  1. F100253E01
    Using SST and a hammer, install the new manual transmission case oil seal.
    SST
    09316-60011   (09316-00011)

    Drive in depth:
    2.1 to 3.1 mm (0.083 to 0.122in.)

    NOTICE:
    Do not damage the oil seal lip.


2. INSTALL TRANSAXLE CASE OIL SEAL
  1. Coat the lip of a new oil seal with MP grease.

  1. F100252E01
    Using SST and a hammer, install the new manual transaxle case oil seal.
    SST
    09636-20010  

    Drive in depth:
    1.7 to 2.7 mm (0.067 to 0.106 in.)

    NOTICE:
    Do not damage the oil seal lip.


3. INSTALL FRONT DRIVE SHAFT ASSEMBLY LH
  1. for Automatic Transaxle:

    1. Coat the spline of the inboard joint with ATF.

  1. for Manual Transaxle:

    1. Coat the spline of the inboard joint with gear oil.

  1. C116899
    Align the inboard joint splines and install the drive shaft with a screwdriver and hammer.

    NOTICE:
    1. Face the cut area of the front drive inboard joint hole snap ring downward.
    2. Do not damage the oil seal.
    3. Do not damage the inboard joint boot.

    HINT:
    Confirm whether the drive shaft is securely driven in by checking the reaction force and sound.


4. INSTALL FRONT DRIVE SHAFT ASSEMBLY RH

HINT:
The installation procedure for the RH side is the same as that for the LH side.


5. INSTALL FRONT AXLE ASSEMBLY LH
  1. Push the front axle out of the vehicle to align the spline of the drive shaft with the front axle and insert the front axle.

    NOTICE:
    1. Do not push the front axle further out of the vehicle than is necessary.
    2. Do not damage the outboard joint boot.
    3. Check for any foreign matter on the speed sensor rotor and insertion part.
    4. Do not damage the speed sensor rotor.


6. INSTALL FRONT AXLE ASSEMBLY RH

HINT:
The installation procedure for the RH side is the same as that for the LH side.


7. INSTALL FRONT STABILIZER LINK ASSEMBLY LH

C106044
  1. Install the stabilizer link with the nut.

    Torque:
    74 N*m{ 755 kgf*cm , 55 ft.*lbf }

    HINT:
    If the ball joint turns together with the nut, use a socket hexagon wrench 6 to hold the stud.


8. INSTALL FRONT STABILIZER LINK ASSEMBLY RH

HINT:
The installation procedure for the RH side is the same as that for the LH side.


9. INSTALL TIE ROD END SUB-ASSEMBLY LH

C107961
  1. Install the tie rod end onto the steering knuckle with a new castle nut.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }

    NOTICE:
    If the holes for the clip are not aligned, tighten the nut by a further turn of up to 60°.

  1. Install a new cotter pin.


10. INSTALL TIE ROD END SUB-ASSEMBLY RH

HINT:
The installation procedure for the RH side is the same as that for the LH side.


11. INSTALL FRONT SUSPENSION ARM SUB-ASSEMBLY LOWER NO.1 LH

C107513
  1. Install the lower arm onto the steering knuckle with a new castle nut.

    Torque:
    98 N*m{ 1,000 kgf*cm , 72 ft.*lbf }

    NOTICE:
    If the holes for the clip are not aligned, tighten the nut by a further turn of up to 60°.

  1. Install a new clip.


12. INSTALL FRONT SUSPENSION ARM SUB-ASSEMBLY LOWER NO.1 RH

HINT:
The installation procedure for the RH side is the same as that for the LH side.


13. INSTALL SPEED SENSOR FRONT LH

C112274
  1. Install the speed sensor onto the steering knuckle with the bolt.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

    NOTICE:
    1. Check that the speed sensor tip and installation portion are free of foreign matter.
    2. Install the speed sensor without turning it from its original installation angle.

  1. C125274
    Install the flexible hose and speed sensor with the bolt.

    Torque:
    29 N*m{ 300 kgf*cm , 22 ft.*lbf }

    NOTICE:
    Install the flexible hose and speed sensor without twisting them.


14. INSTALL SPEED SENSOR FRONT RH

HINT:
The installation procedure for the RH side is the same as that for the LH side.


15. INSTALL FRONT AXLE SHAFT LH NUT

C057566
  1. Using a 30 mm socket wrench, install a new axle hub nut.

    Torque:
    216 N*m{ 2,203 kgf*cm , 160 ft.*lbf }

  1. Using a chisel and hammer, caulk the axle hub nut.


16. INSTALL FRONT AXLE SHAFT RH NUT

HINT:
The installation procedure for the RH side is the same as that for the LH side.


17. INSTALL FRONT WHEELS

Torque:
103 N*m{ 1050 kgf*cm , 76 ft.*lbf }


18. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


19. ADD TRANSAXLE OIL

20. INSPECT AND ADJUST TRANSAXLE OIL
  1. Stop the vehicle in a level place.

  1. Remove the transmission filler plug and the gasket.

  1. D025304E03
    Check that the oil surface is within 5 mm (0.20 in.) of the bottom of the transmission filler plug opening.

    NOTICE:
    1. Excessively large or small amounts of oil may cause problems.
    1. After replacing the oil, drive the vehicle and check the oil level again.

  1. Check for oil leakage if the oil level is low.

  1. Install the transmission filler plug and a new gasket.

    Torque:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }


21. INSPECT ABS SPEED SENSOR SIGNAL
(Click here)

22. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
(Click here)

23. CHECK FOR TRANSAXLE OIL LEAKAGE
← REMOVAL (from Aug 2005)COMPONENTS (from Aug 2005) →