2005-2008 Yaris · Service Manual ENGINE

FREEZE FRAME DATA

Troubleshooting · Vehicles built from Nov 2006


DESCRIPTION
  1. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame date can be helpful in determining whether the vehicle was running or stopped, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

    HINT:
    If it is impossible to duplicate the problem even though a DTC is detected, confirm the freeze frame data.


  1. A103809E18
    The ECM records engine conditions in the form of freeze frame data every 0.5 seconds. Using an intelligent tester, 5 separate sets of freeze frame data can be checked.
    1. 3 data sets before the DTC was set.
    2. 1 data set when the DTC was set.
    3. 1 data set after the DTC was set.
    1. These data sets can be used to simulate the condition of the vehicle around the time of the occurrence of the malfunction. The data may assist in identifying the cause of the malfunction, and in judging whether it was temporary or not.

LIST OF FREEZE FRAME DATA
LABEL
(Tester Display)
Measurement Item/Range
Diagnostic Note
Injector
Injection period of No. 1 cylinder
-
IGN Advance
Ignition timing advance for No. 1 cylinder
-
Calculate Load
Calculated load by ECM
-
Vehicle Load
Vehicle load
Load percentage in terms of maximum intake air flow amount
MAF
Mass air flow volume
If approximately 0.0 g/sec:
  1. Mass air flow meter power source circuit open or shorted
  1. VG circuit open or shorted
If 160.0 g/sec or more:
  1. E2G circuit open
Engine Speed
Engine speed
-
Vehicle Speed
Vehicle speed
Speed indicated on speedometer
Coolant Temp
Engine coolant temperature
If -40°C (-40°F), sensor circuit open
If 140°C (284°F), sensor circuit shorted
Intake Air
Intake air temperature
If -40°C (-40°F), sensor circuit open
If 140°C (284°F), sensor circuit shorted
Air-Fuel Ratio
Ratio compared to stoichiometric level
-
Purge Density Learn Value
Learning value of purge density
-
Evap Purge Flow
Ratio of evaporative purge flow to intake air volume
-
EVAP (Purge) VSV
Purge VSV duty ratio
-
Knock Correct Learn Value
Correction learning value of knocking
-
Knock Feedback Value
Feedback value of knocking
-
Accelerator Position No. 1
Absolute accelerator pedal position No. 1
-
Accelerator Position No. 2
Absolute accelerator pedal position No. 2
-
Throttle Position
Throttle position
-
Throttle Sensor Position
Throttle sensor positioning
-
Throttle Sensor Position #2
Throttle sensor positioning No. 2
-
Throttle Motor
Throttle actuator
-
O2S B1 S2
Heated oxygen sensor output voltage for sensor 2
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensor
AFS B1 S1
Air fuel ratio sensor output voltage for sensor 1
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensor
Total FT #1
Total fuel trim
-
Short FT #1
Short-term fuel trim
Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio
Long FT #1
Long-term fuel trim
Overall fuel compensation carried out in long-term to compensate for continual deviation of short-term fuel trim from central value
Fuel System Status (Bank 1)
Fuel system status (Bank 1)
  1. OL (Open Loop): Has not yet satisfied conditions to go closed loop
  1. CL (Closed Loop): Using heated oxygen sensor as feedback for fuel control
  1. OL DRIVE: Open loop due to driving conditions (fuel enrichment)
  1. OL FAULT: Open loop due to detected system fault
  1. CL FAULT: Closed loop but heated oxygen sensor, which is used for fuel control, malfunctioning
Fuel System Status (Bank 2)
Fuel system status (Bank 2)
Unused
AF FT B1 S1
Short-term fuel trim associated with sensor 1
-
AFS B1 S1
A/F sensor current for sensor 1
Performing INJ VOL or A/F CONTROL function of ACTIVE TEST enables technician to check output voltage of sensor
Catalyst Temp (B1 S1)
Estimated catalyst temperature (sensor 1)
-
Catalyst Temp (B1 S2)
Estimated catalyst temperature (sensor 2)
-
Initial Engine Coolant Temp
Engine coolant temperature at engine start
-
Initial Intake Air Temp
Intake air temperature at engine start
-
Initial Exhaust Temp (In)
Exhaust gas temperature
-
Injection Volume (Cylinder 1)
Injection volume
-
ACC Relay
ACC (cut) relay (ACCR terminal output status)
-
Starter Relay
Starter relay (STAR terminal output status)
-
Starter Signal
Starter switch (STSW) signal
-
Starter Control
Starter control
-
Power Steering Switch
Power Steering Signal
-
Power Steering Signal
Power Steering Signal (history)
Signal status usually ON until ignition switch is turned off
Closed Throttle Position SW
Closed throttle position switch
-
A/C Signal
A/C signal
-
Neutral Position SW Signal
Park/neutral position switch status
-
Electrical Load Signal
Electrical load signal
-
Stop Light Switch
Stop light switch
-
Immobiliser Communication
Immobiliser status
-
Fuel Cut Condition
Fuel cut status
-
Battery Voltage
Battery voltage
-
Atmosphere Pressure
Atmosphere pressure
-
EVAP Purge VSV
Purge VSV
-
Fuel Pump/Speed Status
Fuel pump/speed status
-
VVT Control Status (Bank 1)
VVT control status (bank 1)
-
Electric Fan Motor
Electric fan motor
-
TC and TE1
TC and TE1 terminals of DLC3
-
Engine Speed of Cyl #1
Engine rpm during No. 1 cylinder fuel cut
Active Test support data
Engine Speed of Cyl #2
Engine rpm during No. 2 cylinder fuel cut
Active Test support data
Engine Speed of Cyl #3
Engine rpm during No. 3 cylinder fuel cut
Active Test support data
Engine Speed of Cyl #4
Engine rpm during No. 4 cylinder fuel cut
Active Test support data
Av Engine Speed of All Cyl
Average of engine rpm values during fuel cut of No. 1 to No. 4 cylinders
Active Test support data
VVT Aim Angle (Bank 1)
VVT aim angle (bank 1)
Active Test support data
VVT Change Angle (Bank 1)
VVT change angle (bank 1)
Active Test support data
VVT OCV Duty (Bank 1)
VVT OCV operation duty (bank 1)
Active Test support data
VVT Ex Hold Lrn Val (Bank1)
VVT exhaust hold duty ratio learning value (bank 1)
Active Test support data
VVT Ex Chg Angle (Bank1)
VVT exhaust change angle (bank 1)
Active Test support data
VVT Ex OCV Duty (Bank1)
VVT exhaust OCV duty (bank 1)
Active Test support data
Idle Fuel Cut
Idle fuel cut
ON: when throttle valve fully closed and engine speed over 1,500 rpm
FC TAU
Fuel cut with very light load
Fuel cut being performed with very light load to prevent incomplete engine combustion
Ignition *1
Ignition counter
-
Cylinder #1 Misfire Rate *1
No. 1 cylinder misfire rate
Displayed only during idling
Cylinder #2 Misfire Rate *1
No. 2 cylinder misfire rate
Displayed only during idling
Cylinder #3 Misfire Rate *1
No. 3 cylinder misfire rate
Displayed only during idling
Cylinder #4 Misfire Rate *1
No. 4 cylinder misfire rate
Displayed only during idling
All Cylinders Misfire Rate *1
All cylinders misfire rate
Displayed only during idling
Misfire RPM *1
Engine speed when misfire occurs
-
Misfire Load *1
Engine load when misfire occurs
-
Misfire Margin *1
Margin to detect engine misfire
-
Engine Run Time
Accumulated engine running time
-
Time after DTC Cleared
Cumulative time after DTC cleared
-
Distance from DTC Cleared
Accumulated distance after DTC cleared
-
Warmup Cycle Cleared DTC
Warm-up cycle after DTC cleared
-

HINT:
*1: For Euro-OBD vehicles

← DTC CHECK / CLEAR (from Nov 2006)CHECK MODE PROCEDURE (from Nov 2006) →