2005-2008 Yaris · Service Manual BODY

TERMINALS OF ECU

System information · Vehicles built from Nov 2005


POWER WINDOW REGULATOR MOTOR ASSEMBLY (ON THE DRIVER DOOR) (POWER WINDOW ECU)
B121517E01
  1. Disconnect the G8 or F8 power window regulator motor assembly connector (on the driver side).

  2. Measure the resistance and voltage of the wire harness side connector.

    Standard: (LHD) 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E (G8-1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    +B (G8-2) - E (G8-1)
    LG - W-B
    Battery power supply
    Ignition switch on (IG)
    10 to 14 V
    U (G8-10) - E (G8-1)
    R - W-B
    Driver side door power window motor UP
    Always
    Below 1 Ω
    D (G8-7) - E (G8-1)
    G - W-B
    Driver side door power window motor DOWN
    Always
    Below 1 Ω
    LED (G8-5) - E (G8-1)
    W - W-B
    Ignition power supply
    Ignition switch on (IG)
    10 to 14 V
    If the result is not as specified, there may be a malfunction in the wire harness.
    Standard: (RHD) 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E (F8-1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    +B (F8-2) - E (F8-1)
    LG - W-B
    Battery power supply
    Ignition switch on (IG)
    10 to 14 V
    U (F8-10) - E (F8-1)
    R - W-B
    Driver side door power window motor UP
    Always
    Below 1 Ω
    D (F8-7) - E (F8-1)
    G - W-B
    Driver side door power window motor DOWN
    Always
    Below 1 Ω
    LED (F8-5) - E (F8-1)
    W - W-B
    Ignition power supply
    Ignition switch on (IG)
    10 to 14 V
    If the result is not as specified, there may be a malfunction in the wire harness.


CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
B112771E02
  1. Disconnect the G1 or F7 master switch connector.

  2. Measure the resistance and voltage of the wire harness side connector.

    Standard: (LHD) 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E (G1-7) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    B (G1-15) - Body ground
    GR - Body ground
    Ignition power supply
    Ignition switch on (IG)
    10 to 14 V
    B (G1-15) - Body ground
    GR - Body ground
    Ignition power supply
    Ignition switch off
    Below 1 V
    If the result is not as specified, there may be a malfunction in the wire harness.
    Standard: (RHD) 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E (F7-7) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    B (F7-15) - Body ground
    GR - Body ground
    Ignition power supply
    Ignition switch on (IG)
    10 to 14 V
    B (F7-15) - Body ground
    GR - Body ground
    Ignition power supply
    Ignition switch off
    Below 1 V
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the G1 or F7 master switch connector.

  4. Reset the power window regulator motor.

  5. Measure the voltage.

    Standard voltage: (LHD) 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    U (G1-18) - E (G1-7)
    R - W-B
    Driver side door power window motor UP output
    Ignition switch on (IG), driver power window switch OFF
    Below 1 V
    U (G1-18) - E (G1-7)
    R - W-B
    Driver side door power window motor UP output
    Ignition switch on (IG), driver power window switch UP (manual operation)
    10 to 14 V
    U (G1-18) - E (G1-7)
    R - W-B
    Driver side door power window motor UP output
    Ignition switch on (IG), driver side power window fully open → driver side power window switch UP (AUTO operation) → driver side power window fully closed
    Below 1 V → 10 to 14 V → Below 1 V
    D (G1-10) - E (G1-7)
    G - W-B
    Driver side door power window motor DOWN output
    Ignition switch on (IG), driver side power window switch OFF → DOWN (manual operation)
    Below 1 V → 10 to 14 V
    D (G1-10) - E (G1-7)
    G - W-B
    Driver side door power window motor DOWN output
    Ignition switch on (IG), driver side power window fully closed → driver side power window switch DOWN (AUTO operation) → driver side power window fully open
    Below 1 V → 10 to 14 V → Below 1 V
    If the result is not as specified, the switch may have a malfunction.
    Standard voltage: (RHD) 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    U (F7-9) - E (F7-7)
    R - W-B
    Driver side door power window motor UP output
    Ignition switch on (IG), driver power window switch OFF
    Below 1 V
    U (F7-9) - E (F7-7)
    R - W-B
    Driver side door power window motor UP output
    Ignition switch on (IG), driver power window switch UP (manual operation)
    10 to 14 V
    U (F7-9) - E (F7-7)
    R - W-B
    Driver side door power window motor UP output
    Ignition switch on (IG), driver side power window fully open → driver side power window switch UP (AUTO operation) → driver side power window fully closed
    Below 1 V → 10 to 14 V → Below 1 V
    D (F7-6) - E (F7-7)
    G - W-B
    Driver side door power window motor DOWN output
    Ignition switch on (IG), driver side power window switch OFF → DOWN (manual operation)
    Below 1 V → 10 to 14 V
    D (F7-6) - E (F7-7)
    G - W-B
    Driver side door power window motor DOWN output
    Ignition switch on (IG), driver side power window fully closed → driver side power window switch DOWN (AUTO operation) → driver side power window fully open
    Below 1 V → 10 to 14 V → Below 1 V
    If the result is not as specified, the switch may have a malfunction.


POWER WINDOW REGULATOR SWITCH ASSEMBLY (PASSENGER DOOR)
B121518E01
  1. Reconnect the F1 or G7 switch connector.

  2. Measure the voltage of the connector.

    Standard voltage: (LHD) 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    B (F1-3) - Body ground
    L - Body ground
    Ignition power supply
    Ignition switch off
    Below 1 V
    B (F1-3) - Body ground
    L - Body ground
    Ignition power supply
    Ignition switch on (IG)
    10 to 14 V
    U (F1-4) - Body ground
    R - Body ground
    Passenger side door power window motor UP output
    Ignition switch on (IG), power window switch OFF → UP
    Below 1 V → 10 to 14 V
    D (F1-1) - Body ground
    G - Body ground
    Passenger side door power window motor DOWN output
    Ignition switch on (IG), power window switch OFF → DOWN
    Below 1 V → 10 to 14 V
    SU (F1-5) - Body ground
    W - Body ground
    Power window motor UP input (Remote)
    Ignition switch on (IG), power window master switch OFF → UP (Remote)
    Below 1 V → 10 to 14 V
    SD (F1-2) - Body ground
    P - Body ground
    Power window motor DOWN input (Remote)
    Ignition switch on (IG), power window master switch OFF → DOWN (Remote)
    Below 1 V → 10 to 14 V
    If the result is not as specified, the switch may have a malfunction.
    Standard voltage: (RHD) 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    B (G7-3) - Body ground
    L - Body ground
    Ignition power supply
    Ignition switch off
    Below 1 V
    B (G7-3) - Body ground
    L - Body ground
    Ignition power supply
    Ignition switch on (IG)
    10 to 14 V
    U (G7-4) - Body ground
    R - Body ground
    Passenger side door power window motor UP output
    Ignition switch on (IG), power window switch OFF → UP
    Below 1 V → 10 to 14 V
    D (G7-1) - Body ground
    G - Body ground
    Passenger side door power window motor DOWN output
    Ignition switch on (IG), power window switch OFF → DOWN
    Below 1 V → 10 to 14 V
    SU (G7-5) - Body ground
    W - Body ground
    Power window motor UP input (Remote)
    Ignition switch on (IG), power window master switch OFF → UP (Remote)
    Below 1 V → 10 to 14 V
    SD (G7-2) - Body ground
    P - Body ground
    Power window motor DOWN input (Remote)
    Ignition switch on (IG), power window master switch OFF → DOWN (Remote)
    Below 1 V → 10 to 14 V
    If the result is not as specified, the switch may have a malfunction.


CHECK MAIN BODY ECU
E114510E10
B108612E04
B108641E02
  1. Disconnect the 4A, 4B, 4E and 4S main body ECU (vehicle rear side) connectors.

  2. Disconnect the D64 or D33 main body ECU (vehicle front side) connector.

  3. Measure the voltage and resistance of the wire harness side connectors.

    Standard: 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    BECU (4B-30) - GND1 (4E-17)
    L - W-B
    Battery (power supply)
    Always
    10 to 14 V
    IG (4S-7) - GND1 (4E-17)
    R - W-B
    Ignition power supply
    Ignition switch on (IG)
    10 to 14 V
    IG (4S-7) - GND1 (4E-17)
    R - W-B
    Ignition power supply
    Ignition switch off
    Below 1 V
    DCTY (4A-21) - Body ground
    R - Body ground
    Driver side door courtesy light switch input
    Driver side door closed
    10 kΩ or higher
    DCTY (4A-21) - Body ground
    R - Body ground
    Driver side door courtesy light switch input
    Driver side door open
    Below 1 Ω
    PCTY (4A-24) - Body ground
    L - Body ground
    Passenger side door courtesy light switch input
    Passenger side door closed
    10 kΩ or higher
    PCTY (4A-24) - Body ground
    L - Body ground
    Passenger side door courtesy light switch input
    Passenger side door open
    Below 1 Ω
    CANP (D64-23)*1 - Body ground
    BR*3 - Body ground
    P*4 - Body ground
    CAN communication line
    Always
    10 kΩ or higher
    CANP (D33-4)*2 - Body ground
    BR*3 - Body ground
    P*4 - Body ground
    CAN communication line
    Always
    10 kΩ or higher
    GND1 (4E-17) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    *1: w/ Entry and start system
    *2: w/o Entry and start system
    *3: LHD
    *4: RHD
    If the result is not as specified, there may be a malfunction on the wire harness side.

← PROBLEM SYMPTOMS TABLE (from Nov 2005)FAIL-SAFE CHART (from Nov 2005) →